sewer pipe test Articles

  • Sewer-Main Collection Pipe Joint Infiltration Testing and Life Cycle Cost Analysis

    ABSTRACTResearch ProjectsMajor members of the sewer-main pipe manufacturing industry and the University of Houston have completed and published the results of the following two research projects: The Sewer-Main Collection Pipe Joint Infiltration Testing research project that measured the water infiltration rate of water-tight designed 30-inch pipe joints. The joint tightness testing was ...

  • BOSS 2000 HDPE Storm Sewer Pipe, Stettler, AB

    Owner: Town of Stettler Installer: Woooden Construction Ltd. Designer: Associated Engineering Alberta Ltd. Location: 57 Street, Stettler, Alberta As part of a sanitary main replacement project, the Town of Stettler was faced with the challenge of replacing an aging storm sewer line under very low cover conditions. ...


    By Armtec

  • Site acceptance test 12 inch sewer bypass pumps

    Following a European call for tender during the summertime, we were awarded the contract to supply several sewage and flood control pumps. One of the key requirements was an official SAT (Site Acceptance Test). Recently, we successfully completed the first delivery of 12 inch sewage pumps including piping. This video shows how easy it is to set up the complete installation.  Some of the key ...


    By BBA Pumps North America

  • A novel freeze protection strategy for shallow buried sewer pipes: temperature modelling and field investigation

    The burial of sewer and water pipes below the maximum ground frost depth can be very costly and laborious in regions with cold winters. If a freeze protection measure is applied, the utility lines can be installed in a shallower trench to reduce the excavation needs. One freeze protection measure, so called heat tracing, consists of supplying heat along the pipes. In this work, the use of 4th ...


    By IWA Publishing

  • Sedimentation dynamics in combined sewer systems

    Sediments in combined sewers may negatively affect the performance of sewer systems and significantly promote the formation of hydrogen sulfide. To prevent this, German sewer systems are cleaned regularly but at high costs. In order to optimize the cleaning intervals, this study investigates how deposits build up and change over a defined period under constant conditions. The experiments were ...


    By IWA Publishing

  • Quantitative pipe condition assessment with Pipe Penetrating Radar

    Abstract Pipe Penetrating Radar (PPR) is the underground in-pipe application of GPR, a non-destructive testing method that can detect defects and cavities within and outside mainline diameter (>18 in / 450mm) non-ferrous (reinforced concrete, vitrified clay, PVC, HDPE, etc.) pipes. The key advantage of PPR is the unique ability to map pipe wall thickness and deterioration including voids ...


    By SewerVUE

  • Accepted Inspection Methods of Process Sewers.

    During the process of refining there is discharge of hazardous waste, this coupled with aging pipeline infrastructure creates a potential where waste can leak into the environment posing catastrophic threats to life. Federal agencies such as the EPA are beginning to penalize refineries that do not take necessary measures of disposing their waste. These refineries are subject to ...


    By EnTech Engineering Company

  • Valuing information for sewer replacement decisions

    Decision-making for sewer asset management is partially based on intuition and often lacks explicit argumentation, hampering decision transparency and reproducibility. This is not to be preferred in light of public accountability and cost-effectiveness. It is unknown to what extent each decision criterion is appreciated by decision-makers. Further insight into this relative importance improves ...


    By IWA Publishing

  • Underground research for sewer optimization - Case Study

    Project Underground research for sewer optimization Client The local authority of Bergen in co-operation with Tauw Consultancy Country The Netherlands Background and objective The local authority of Bergen in North Holland wants to limit the management costs of the sewer system. The ...


    By Eijkelkamp Soil & Water

  • Case study - Muskegon County - Sewer Force Mains

    Service: Sahara Client: Muskegon County Type of Pipeline: Sewer Force Main Diameter: 66-inch Pipe Material: PCCP Length: 8.5 miles 13.7 km In 2007, Muskegon County’s 35-year old large diameter wastewater force main failed catastrophically. Although historical data demonstrated that joint leakage had never contributed to previous events, extensive failure analysis of ...

  • Installing gravity sewer in tough Georgia rock

    It took a contractor who was receptive to an innovative new installation approach, a good deal of patience and a whole lot of determination — after two previous attempts by other contractors using drills and air hammers were unsuccessful — to finally conquer a pesky 800-foot (243.8 m) stretch of tough Georgia blue granite. Hence, project owner Coweta County Water and Sewer Authority ...


    By Vermeer

  • Particle velocity and sediment transport at the limit of deposition in sewers

    This paper focuses on the sediment particle while it is transported at the limit of deposition in storm sewers, i.e. as bed load at the limit of concentration that leads to sediment deposition. Although many empirical sediment transport equations are known in the literature, there is only limited knowledge concerning particle velocity. Sediment particle and sphere velocity measurements were ...


    By IWA Publishing

  • Quantifying Sub-Surface Discharges from Individual Sewer Defects

    ABSTRACTThe California Regional Water Quality Control Board, Santa Ana Region (RWQCB) required wastewater collection agencies in Orange County to report discharges from “pipe breaks, leaking sewer pipes and joints, and other subsurface discharges of wastewater.” The Orange County Sanitation District (OCSD), in conjunction with a research team from University of California, Irvine (UCI), developed ...

  • Robot Device for Pipe Inspection - Case Study

    In 2005, Pure Technologies (Pure), a provider of various structural monitoring and leak-detection technologies, set about to develop a pipeline assessment tool that could monitor and report on the condition of pre-stressed concrete cylinder pipes (PCCP) utilized in municipal water and sewer systems. The tool’s competitive advantage would be accurate assessment decoupled from the need to ...

  • Rapid detection of sewer defects and blockages using acoustic-based instrumentation

    Sewer flooding incidents in the UK are being increasingly associated with the presence of blockages. Blockages are difficult to deal with as although there are locations where they are more likely to occur, they do occur intermittently. In order to manage sewer blockage pro-actively sewer managers need to be able to identify the location of blockages promptly. Traditional closed-circuit ...


    By IWA Publishing

  • Ability of Preissmann slot scheme to simulate smooth pressurisation transient in sewers

    Urban drainage networks are generally designed to operate in a free-surface flow condition. However, as a consequence of heavy rainfall events or network malfunctions, the filling of sewers (pressurisation) and network overflow may occur. Several modelling software products are commonly used to simulate floods in drainage networks, and their results are usually thought to be reliable and robust. ...


    By IWA Publishing

  • Link-Pipe Inc.’s Grouting Sleeve - Case Study

    Background Link-Pipe Grouting Sleeve is manufactured by Link-Pipe inc. of Canada. It is a local repair system developed for the structural renovation of gravity sewers. The system is comprised of a stainless steel structural core, which uses a mechanical lock to hold it against the host pipe, the core is surrounded by an absorbent foam gasket. Limit straps prevent the sleeve ...


    By Link-Pipe Inc.

  • Monitoring accumulation sediment characteristics in full scale sewer physical model with urban wastewater

    A series of experiments were carried out with real wastewater in a pilot flume located at A Coruña wastewater treatment plant (WWTP) (Spain). A full scale model was developed to test a circular (300 mm inner diameter) and an equivalent area egg-shaped plastic pipe under controlled experimental conditions (pipe slope 2–5‰, averaged discharge Q = 4 L/s). Velocity profiles and sediment ...


    By IWA Publishing

  • Modeling fats, oil and grease deposit formation and accumulation in sewer collection systems

    Fats, oil and grease (FOG) deposits in sewer systems are responsible for approximately 25% of all annual line blockages in the United States and lead to the release of 3–10 million gallons of untreated wastewater to the surrounding environment. Considerable effort has been made to maintain the conveyance of wastewater by cleaning pipes that have a significant FOG deposit accumulation. Changes ...


    By IWA Publishing

  • Applications of Pipe Penetrating Radar for Advanced Pipe Condition Assessments: the Clark Regional Wastewater District (WA) Case Study

    Abstract Pipe Penetrating Radar (PPR) is the underground in-pipe application of GPR, a non-destructive testing method that can detect defects and cavities within and outside mainline diameter non-metallic (reinforced concrete, vitrified clay, PVC, HDPE, etc.) underground pipes. The key advantage of PPR is the unique ability to map pipe wall thickness and deterioration including voids outside ...


    By SewerVUE

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you