These 2-1/2-in. pressure gauges feature a spiral bourdon tube and full-scale accuracy of ± 1.6%. Cases are 304 stainless steel, and are glycerine filled for built-in pulsation dampening. With 1/4-inch NPT bottom connection. They are offered in 18 standard dual-scale (psi and bar) ranges, from 0-30 to 0-15,000 psi.
The filter elements are replaceable. They have pleated stainless steel wire cloth or cellose over a metal support tube. Choose from six micron ratings, from 238 to 3. Machined aluminum, stainless steel and steel housings. Rated from 6 to 15-gpm (suction), 12 to 22 (return line). Mounting clamps sold as option.
These line-mounted devices consist of a spring-loaded disc built into a reducing pipe bushing. They can be used to ensure flow through a partial-flow heat exchanger, provide required back pressure in drain lines, and many other places. Eliminates the need for more expensive relief and check valves, gets the same results. Various spring ratings.
The In-Line Power Jet Siphon is designed for use with two or more Fol-Da-Tanks. When the tanks are not close together, an In-Line Power Jet Siphon attached to two hard suction hoses assist water transfer from one tank to another. This keeps the main tank full of water for drafting as the secondary tank is refilled.
S. P. Kinney is most noted for our heavy-duty Model A and Model AP Automatic Self-Cleaning Strainers. The Model AP is designed for operation where the pressure is less than 20 psi. Both models employ the use of a rotating cylindrical drum with a number of threaded holes containing one of many types of straining media. The drum is supported on a ...
The Low Pressure Series automatic water filters utilize an electric motor to assist cleaning during the backwash cycle. Low Pressure models make self-cleaning filtration possible at lower pressures. They are necessary where the minimum 35 psi system pressure is not available. Motor Run filters operate at system pressures as low as 15 psi. All 180 ...
Pleated stainless wire elements are housed in Y-shaped housings for four times the element area of a typical Y-strainer. For suction and return line service. Pipe sizes 1/2 thru 2 in., with a choice of element ratings down to 25 micron. Other sizes available.
The ultimate in sensible, workable suction and return line hydraulic (or other) fluids. Elements offered from 30-mesh wire to 3-micron paper. They are serviced through a clean-out cover. Housings are low-cost, large-diameter steel tubes. Port sizes from 1 to3-in. NPT.
The desiccant tank breather is a unique, patented air filter and water vapor removal system. These hygroscopic breathers prevent water and contaminants from entering fluid reservoirs as differential pressures occur through thermal expansion and contraction of the fluid.
S.P. Kinney can custom design filtration packages for any application. S.P. Kinney oﬀers a wide range of custom manual and automatic designs to meet any dimensional, pressure, or temperature requirements that a customer may have.
Heavy duty glass-reinforced polypropylene. 3 ˝ cam lever cap for easy cleaning. 316 stainless steel screen. 8 ˝ long full-flow screen. 14 mesh screen standard. Screens available in 6,14, 30, 40, and 80 mesh. Viton O-ring. EPDM gaskets standard. Operating pressure: 100 psi max @ 70 deg F.
Series 758A 'Y' Pattern Strainers are installed in water piping systems to protect expensive equipment (such as backflow preventers) from damage or failure that can be caused by foreign material in the pipeline. Series 758A feature cast iron bodies. Maximum Working Pressure: 200psi (13.8 bar). Size(s): 2 1/2 to 10 in. (65 to 250mm)
The Model AM is S.P. Kinney’s light-duty Manual Strainer that is similar in design to the Model A. The Model AM is designed for operation where the pressure 20 psi and up. The strainer employs the use of a manually rotated cylindrical drum with a number of threaded holes containing one of many types of straining media. The drum positioned ...