plastic pipe system News
-
ASTM F2805 - 11 standard specification for multilayer thermoplastic and flexible steel pipe and connections
1. Scope 1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, markings for factory manufactured multilayer flexible steel pipe with thermoplastic inner and outer layers and end connections (Fig. 1). It covers nominal sizes 2 in. through 8 in. (50 mm through 200 mm). Flexible steel pipes are multilayered pipe products manufactured in ...
-
ASTM F1335-04 standard specification for pressure-rated composite pipe and fittings for elevated temperature service (Withdrawn 2011)
Withdrawn Rationale: This specification covers pressure-rated composite pipe and fittings for the transport of hot or cold liquids, beverages, or gases that are compatible with the composite pipe and fittings. Formerly under the jurisdiction of Committee F17 on Plastic ...
-
ASTM F667 - 12 Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings
This specification covers requirements and test methods for materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, bond, and marking of corrugated polyethylene (PE) pipe and fittings. This specification covers tubularly extruded, spirally ...
-
ASTM D3139 - 98(2011) standard specification for joints for plastic pressure pipes using flexible elastomeric seals
This specification covers the two types of joints, mechanical joint and push-on-joint, required for plastic pipe pressure systems with a wall thickness equal to or greater than that of SDR 64 intended for use in supply and distribution lines for water using flexible elastomeric seals. The joint ...
-
ASTM F1281 - 11 standard specification for crosslinked polyethylene/aluminum/crosslinked polyethylene (PEX-AL-PEX) pressure pipe
This specification covers a coextruded cross linked polyethylene composite pressure pipe with welded aluminum tube reinforcement between the inner and outer layers. The inner and outer cross linked polyethylene layers are bonded to the aluminum tube by a melt adhesive. Included is a system of nomenclature for the cross linked polyethylene-aluminum cross linked polyethylene (PEX-AL-PEX) pipes, the ...
-
ASTM F1563 - 01(2011) standard specification for tools to squeeze-off polyethylene (pe) gas pipe or tubing
This specification covers the physical requirements for tools used to squeeze-off polyethylene gas pipe and tubing. The squeeze bars shall be of a size and configuration that compresses the pipe walls to reduce the gas flow, but does not damage the pipe and ...
-
ASTM F2263 - 07(2011) Standard Test Method for Evaluating the Oxidative Resistance of Polyethylene (PE) Pipe to Chlorinated Water
1. Scope 1.1 This test method describes the general requirements for evaluating the long-term, chlorinated water, oxidative resistance of polyethylene (PE), used in cold water supply or service systems by exposure to chlorinated water. This test method outlines the requirements of a pressurized ...
-
ASTM D2239 - 12 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
This specification covers polyethylene (PE) pipe made in standard thermoplastic pipe dimension ratios and pressure rated for water. Polyethylene plastics used to make pipe meeting the requirements of this specification are categorized in two criteria: short-term strength tests and long-term strength tests. The plastics are defined by four hydrostatic design stresses ...
-
ASTM F1987 - 01(2011) standard specification for multilayer pipe type 2, compression fittings, and compression joints for hydronic heating systems
This specification covers requirements for multilayer pipe type 2 and compression fittings for hydronic heating systems. Multilayer Pipe Type is a construction-based pressure rated pipe comprising more than one layer in which at least 60 % of the ...
-
ASTM D2737 - 12e1 Standard Specification for Polyethylene (PE) Plastic Tubing
This specification covers polyethylene (PE) tubing pressure-rated for water. Included here are criteria for classifying PE plastic tubing materials and PE plastic tubing, and requirements and test methods for materials, workmanship, dimensions, bond strength, carbon black, density,.sustained pressure, hydrostatic burst pressure, and environmental stress cracking. ...
-
ASTM D2737 - 12 Standard Specification for Polyethylene (PE) Plastic Tubing
This specification covers polyethylene (PE) tubing pressure-rated for water. Included here are criteria for classifying PE plastic tubing materials and PE plastic tubing, and requirements and test methods for materials, workmanship, dimensions, bond strength, carbon black, density,.sustained pressure, hydrostatic burst pressure, and environmental ...
-
ASTM F1986 - 01(2011) standard specification for multilayer pipe type 2, compression fittings, and compression joints for hot and cold drinking-water systems
This specification covers requirements for multiplayer pipe type 2 and compression fittings for hot and cold drinking water systems. Multilayer pipe type 2 is produced using a butt-welded aluminum pipe as a core, with an extruded inside layer of ...
-
ASTM F876 - 10e1 standard specification for crosslinked polyethylene (PEX) tubing
This specification covers crosslinked polyethylene (PEX) tubing that is outside diameter controlled, made in standard thermoplastic tubing dimension ratios, and pressure rated for water at three temperatures. This specification covers one PEX tubing material in one standard dimension ratio and having pressure ratings for water of three temperatures. The pressure ratings decrease as the ...
-
ASTM D2513 - 11c standard specification for Polyethylene (PE) gas pressure pipe, tubing, and fittings
This specification covers the requirements and test methods for material, dimensions, hydrostatic burst strength, tensile strength, chemical resistance, sustained pressure, heat fusion, and impact resistance of plastic pipes, tubing, and fittings used for direct burial and reliner applications in fuel gas mains and ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you