The kind of waste water from tanneries has a high salt content that can be diluted, but is hard to eliminate. They can also have a high organic load due to the high dirtiness, including blood, sand and manure. The water itself from these industries can vary a lot from a company to another depending on its actividad. However, a common characteristic is the high content of materials in suspension due to fibres and precipitated proteins.
AQUA Industrial Watertreatment is an experienced supplier of wastewater treatment systems for the poultry industry. Many AQUA systems have been installed worldwide at satisfied customers. The waste water produced during the processing of poultry is highly polluted with proteins, fats, carbohydrates, blood, feathers and meat particles. Extensive knowledge of the poultry slaughtering process is essential in the design of an adequate water treatment installation. The method used for the internal transportation of...
Industrial wastewater characterized by an high COD content are an interesting renewable source for the Food and beverage industrial sector which can have them readily available from their industrial processes.
The COD contribution in the wastewater can be easily converted in biogas and then in green energy to reuse inside the factory as both electrical energy and thermal energy.
This process can be applied with the installation of the UASB technology, implemented by Hydroitalia - Colsen in new and existing plants.
Voltammetric determination of many heavy metals is also possible in municipal or industrial wastewater. On account of the usually high organic load the sample is usually mineralized by means of UV digestion.
The wide range of Pieralisi decanters is in fact successfully used by over 15,000 customers around the world for the volume reduction of biological and physical/chemical sludge of both Municipal and Industrial origin.
Optimize Mine Production. We understand that you are facing increased regulations and mining operations continuously deal with challenges presented by harsh and dangerous conditions. Wastewater treatment to meet regulatory and social demands only compounds those challenges. Aeration Industries International can limit the time and effort you spend on wastewater treatment, allowing you to focus on what matters most… production.
The essential challenges of today are to ensure cost effective treatment and recycling processes for water and wastewater. Membrane technology solves this task by being an innovative and trendsetting technology. Today membranes are successfully used for the treatment of municipal and industrial wastewater as well as for the production of drinking and process water from surface water. Membrane technology and membrane bioreactors (MBR) are especially important in arid zones for the recovery of clean water for reuse...
Securing a reliable supply of water for extraction, handling and transportation is vitally important to mining companies looking to expand their operations. These companies will go to great lengths to meet this need, running pipelines hundreds of miles long from desalination plants on the coast and treating wastewater that is conventional held in tailings ponds. Wastewater treatment technologies can recover saleable metal that might otherwise be lost and prevent environmental contamination from highly acidic...
GURNEY ENVIRONMENTAL offers a wide range of products and technologies for the municipal wastewater treatment industry. Our forte is sustainable technologies that offer maximum performance at minimal total ongoing cost.
The food and beverage industry uses water within its production process and for raw material washing, producing large quantities of wastewater. To reduce the water impact index, all the effluents coming from the production process can be reused a second time allowing water saving. IDRAFLOT package flotation units are a technological solution for the separation of suspended solids and oil/fats from a water-based stream.
The effluents that accrue in the cleaning process of silo vehicles and containers for transportation of raw materials for the chemical industry, are highly complex and constantly changing in the composition of wastewater. Flocculation as the prior art of treatment for chemical waste water can not remove many of the completely dissolved invisible substances. Thus, the residual stresses are evident despite high claritv of the `Treated effluent` is often well above the levels witch are applicable for wastewater in...
Conventional wastewater treatment systems are focused on efficient removal of polluting components. This is commonly done through aeration and separation of formed biomass from the cleaned water. After treatment the water would be discharged onto surface waters or subsoil irrigation. Introduction of polishing steps after these treatment systems opened up the possibilities to reuse water for either irrigation or even potable water. DMT Environmental Technology also implements these solutions with its MemBioRex...
Wastewater treatment processes considered for this industry must address industry specific nuances like slug discharges of pulp, stormwater runoff and air emissions for compounds such as total reduced sulfur (TRS)
WesTech partners with manufacturing in every industry worldwide. For raw water treatment, wastewater treatment and water reclamation, process equipment supplied and manufactured by WesTech is designed to work and built to last. Design-build, plant expansions, and upgrades are each approached from a holistic view of the flow sheet and a broad base of experience in yours and other industries with similar challenges, always with an eye for efficiencies that go to the bottom line.
We understand how critical it is to get the industrial cleaning done so your plant can continue operating at peak efficiency. Our cleaners remove dirt, grease, oil, metal fines, flux, and other particulates from stamped metal, parts and equipment without the hazards associated with solvents. Our cleaners are also proven in removing soils from filter membranes used in wastewater treatment systems.
Effective cleaning of machined or formed parts is a key step in all manufacturing processes. At IPC, we understand for a surface to be successfully plated or painted, it must first be free of contaminants. Our cleaners remove dirt, cutting oil, metal fines, flux, and other particulates from stamped metal and precision parts without the hazards associated with solvents. An economical 1-2% concentration in water is effective for most cleaning applications. Our cleaners are also proven in removing soils from filter...
Lagoon SolutionsWith thousands of installations worldwide, Aeration Industries provides lagoon solutions that are built on the experience and expertise that comes from more than 40 years of experience in wastewater treatment. Whether it’s industrial wastewater treatment requiring thorough mixing and high oxygen transfer efficiency, or a municipal wastewater treatment system requiring efficient and effective treatment; Aeration Industries will design a solution to optimize your current lagoon.
Our cleaners are used in the manufacture of semiconductors, flat panel displays, CDs, DVDs, and many other electronic items. They remove emulsions, particulates, oil, organic and inorganic contaminants from quartz, wafers, glass, silicon, ceramics, and metals. When rinsed properly our products leave absolutely no residue. They are also proven in removing soils from filter membranes used in wastewater treatment systems.