impeller pump Equipment available in Congo, Democratic Republic of the

Available in Congo, Democratic Republic of the| Near Congo, Democratic Republic of the
510 Results found

We couldn't find any impeller pump equipment in Congo, Democratic Republic of the

Here is a list of results available in Congo, Democratic Republic of the

Current filtering criteria

You can remove a filter by clicking on the x
  • Category: Water & Wastewater ×

  • Subcategory: Water & Wastewater Pumps ×

  • Keyword: impeller pump ×

  • Available in: Africa ×

  • Available in: Congo, Democratic Republic of the ×

Chemineer - Model JT-2 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The JT-2 Impeller has been developed for superior blending in transitional flow. Higher viscosity and non-Newtonian fluids make blending much more challenging. This impeller is used after conventional turbines have lost efficiency due to viscous effects and before the need for close clearance impellers.

Chemineer - Model RL-3 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The Chemineer RL-3 impeller is designed for applications where a ragless agitator is desired to prevent fibrous material build-up on the rotating impeller. Typical in Waste Treatment applications the RL-3 is a rag shedding impeller which prevents build-up of fibrous materials on the impeller, while providing a strong axial flow for efficient ...

Chemineer - Model S-4 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

A cost effective impeller for operation very near the floor of a tank for agitating the heel in solids suspension applications. Also an effective impeller in laminar flow applications, especially when impeller Reynolds numbers drop below 50.

Chemineer Impeller - Model P-4 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

A reasonably cost effective impeller in both turbulent and laminar flow. Good impeller for applications where the viscosity changes over a wide range causing the flow regime to vary between turbulent and laminar flow. A reasonably cost effective impeller for solids suspension.

Chemineer - Model CD-6 - Concave Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The CD-6 impeller is a second generation gas and immiscible liquid dispersion impeller. The CD-6 can handle about 2.4 times the maximum gas capacity of the D-6 impeller. The CD-6 is similar to the Smith impeller, but there are substantial power and dispersion capability differences. This impeller has been used at aeration numbers as high as 2.1.

Chemineer - Model SC-3 - High Efficiency Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The Chemineer® SC-3 Impeller features an advanced design engineered for deep tanks. It produces flow characteristics of much larger impellers, without the added weight, or the resulting loss in pumping efficiency. The highly efficient SC-3 Impeller's reduced weight allows for the use of longer shaft extensions for deeper tanks, and resolves ...

Prochem Maxflo - Model Mark II & III - Impeller Pumps

by National Oilwell Varco     based in Dayton, OHIO (USA)

High efficiency, high solidity impellers for use in turbulent side entering applications. They are especially effective for fluids possessing a yield value, such as paper stock. The high solidity permits operation nearer the boiling point without cavitation.

Chemineer - Model HE-3 - High-Efficiency Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

An extremely efficient turbulent flow impeller for blending, heat transfer and solids suspension. Most effective for Reynolds numbers over 50. Developed to minimize the creation of trailing vortices and incorporating the otherwise wasted energy into macro-flow.

Chemineer - Model XE-3 - High Efficiency Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The highest efficiency turbulent flow impeller available in the marketplace. Ideal for blending, heat transfer, and solids suspension applications. Developed to maximize strength at lower weights as compared to other axial flow impellers, allowing for longer shafts without internal support, smaller shaft diameters, and smaller seal sizes if ...

Prochem - Model Maxflo WSE - High Efficiency Side Entry Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

A high efficiency, advanced side-entering hydrofoil impeller that produces maximum pumping action. It has more cavitation resistance than other designs through effective hydrodynamic design.

NIROSTAR - Model 2000-A/B - Impeller Pump

by ZUWA-Zumpe GmbH     based in Laufen, GERMANY

By means of the star knobs the pump can be easily opened and cleaned.For maintenance work the pump head can be disconnected from the motor with just a few turns.

Model RV - Helicoidal Impeller Pump

by INOXPA     based in Leinfelden, GERMANY

The RV centrifugal pump with helicoidal impeller is the best solution for the transfer of liquids with solid particles or medium viscosity products that cannot be pumped with an ordinary centrifugal pump. Due to the helicoidal shape of the impeller, the transfer of the product is gentle and without clogging., e.g. solid particles suspended in ...

Johnson Pump - Model DC - Multipurpose Flexible Bronze Impeller Pump

by Johnson Pump - an SPX Corporation brand     based in ÖREBRO, SWEDEN

Multipurpose flexible bronze impeller pump for battery operated applications. These impeller 12/24 V DC close-coupled pumps are ideal for battery operated applications. The series comprises six models – five in bronze and one in a thermoplastic material and they cover flows from 15 to 55 l/min. The F3B-19 Oil change is a reversible rubber ...

Model PLN 618 - 6` Plastic Impeller Pump

by Polmot Motor Mak.San. ve Tic. A.S.     based in Selcuklu /Konya, TURKEY

Max. Sand Content 40 gr/ m3. Frequency 50 Hz. Rotation CCW. Rotational Speed 2900 rpm. Max. VVater Temp. 30°C. Max. Start / Hour 4' - 10 / 6' - 20.

Model PLN 403 - 4` Plastic Impeller Pump

by Polmot Motor Mak.San. ve Tic. A.S.     based in Selcuklu /Konya, TURKEY

Max. Sand Content: 50 gr/ m3. Frequency: 50 Hz. Rotation: CCW. Rotational Speed: 2900 rpm. Max. VVater Temp.: 30°C. Max. Start / Hour: 4' -10.

Model AD ADVANCE SERIES - Flexible Impeller Pumps

by Alphadynamic Pumps Co     based in Kifisia, GREECE

The impeller, deforming itself inside the stainless steel body pump, ensures a quick suction up to 6 meters and a continuous and delicate transfer of the liquid to the outlet. Besides, the low revolution speed makes it suited for trasferring delicated and fragile liquids, and fluids with suspension solids. The pump runs in both rotation directions ...

UNISTAR - Model 2000 - Impeller Pump with Drive

by ZUWA-Zumpe GmbH     based in Laufen, GERMANY

A multi-purpose pump designed for transferring clean or contaminated fluids without abrasive particles (suitable for all non corrosive and non abrasive fluids).

Flexible Impeller Pumps

by Nova Rotors srl     based in Sossano VI, ITALY

The flexible impeller pump is self priming, reversible, compact and efficient also at low rpm. With its simple operation has an easy installation  and maintenance, is suitable for a variety of application and has no pulse. It  can be flanged, 2-speed and optional (variable speed, inverter and other on-demand).

ECO IMPELLER PUMP SC03

by Eco Equipments Inc.     based in Taipei, TAIWAN

This model is designed for pumping jobs such as construction sites and manhole pumping where lightweight, high volume, trash pumps are needed. It has the ability to pass through a 12' opening and pump in debris laden areas. A small hole strainer is available for limiting solids to be pumped. Discharge hole 3' and solids handling 2 1/2'. Its ...

STAC - Model CR Series - Centrifugal Open Impeller Pumps

by STAC s.r.l.     based in Trieste, ITALY

The open impeller allow pumping of clean or relatively dirty water which have solid parts with diameter maximum of 8 mm.

Need help finding the right suppliers?

Let the XPRTs do the work for you