impeller pump Equipment in USA

356 Results found

Current filtering criteria

You can remove a filter by clicking on the x
  • Category: Water & Wastewater ×

  • Subcategory: Water & Wastewater Pumps ×

  • Keyword: impeller pump ×

  • In: USA ×

Chemineer - Model S-4 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

A cost effective impeller for operation very near the floor of a tank for agitating the heel in solids suspension applications. Also an effective impeller in laminar flow applications, especially when impeller Reynolds numbers drop below 50.

Chemineer Impeller - Model P-4 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

A reasonably cost effective impeller in both turbulent and laminar flow. Good impeller for applications where the viscosity changes over a wide range causing the flow regime to vary between turbulent and laminar flow. A reasonably cost effective impeller for solids suspension.

Chemineer - Model RL-3 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The Chemineer RL-3 impeller is designed for applications where a ragless agitator is desired to prevent fibrous material build-up on the rotating impeller. Typical in Waste Treatment applications the RL-3 is a rag shedding impeller which prevents build-up of fibrous materials on the impeller, while providing a strong axial flow for efficient ...

Chemineer - Model JT-2 - Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The JT-2 Impeller has been developed for superior blending in transitional flow. Higher viscosity and non-Newtonian fluids make blending much more challenging. This impeller is used after conventional turbines have lost efficiency due to viscous effects and before the need for close clearance impellers.

Chemineer - Model CD-6 - Concave Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The CD-6 impeller is a second generation gas and immiscible liquid dispersion impeller. The CD-6 can handle about 2.4 times the maximum gas capacity of the D-6 impeller. The CD-6 is similar to the Smith impeller, but there are substantial power and dispersion capability differences. This impeller has been used at aeration numbers as high as 2.1.

Chemineer - Model SC-3 - High Efficiency Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The Chemineer® SC-3 Impeller features an advanced design engineered for deep tanks. It produces flow characteristics of much larger impellers, without the added weight, or the resulting loss in pumping efficiency. The highly efficient SC-3 Impeller's reduced weight allows for the use of longer shaft extensions for deeper tanks, and resolves ...

Prochem Maxflo - Model Mark II & III - Impeller Pumps

by National Oilwell Varco     based in Dayton, OHIO (USA)

High efficiency, high solidity impellers for use in turbulent side entering applications. They are especially effective for fluids possessing a yield value, such as paper stock. The high solidity permits operation nearer the boiling point without cavitation.

Chemineer - Model XE-3 - High Efficiency Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

The highest efficiency turbulent flow impeller available in the marketplace. Ideal for blending, heat transfer, and solids suspension applications. Developed to maximize strength at lower weights as compared to other axial flow impellers, allowing for longer shafts without internal support, smaller shaft diameters, and smaller seal sizes if ...

Chemineer - Model HE-3 - High-Efficiency Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

An extremely efficient turbulent flow impeller for blending, heat transfer and solids suspension. Most effective for Reynolds numbers over 50. Developed to minimize the creation of trailing vortices and incorporating the otherwise wasted energy into macro-flow.

Prochem - Model Maxflo WSE - High Efficiency Side Entry Impeller Pump

by National Oilwell Varco     based in Dayton, OHIO (USA)

A high efficiency, advanced side-entering hydrofoil impeller that produces maximum pumping action. It has more cavitation resistance than other designs through effective hydrodynamic design.

Model K3VN(X) - 3” Submersible, Enclosed Impeller Pump

by Keen Pump Co. Inc.     based in Ashland, OHIO (USA)

3” Submersible, Enclosed Impeller (Class 1, Div.1, Groups C & D Hazardous Location 'Explosion-Proof')

Model K3RN(X) - 3” Submersible, Recessed Impeller Pump

by Keen Pump Co. Inc.     based in Ashland, OHIO (USA)

Handles Stringy and Fibrous Materials. Passes Large Solids. Pumps Heavier Solids Concentrations. Ideal for Grit and Abrasive Solids. Pumping via Vortex Action. Solids Do Not Pass through Impeller. Virtually Impossible to Clog

Model K4VN(X) - 4” Submersible, Enclosed Impeller Pump

by Keen Pump Co. Inc.     based in Ashland, OHIO (USA)

4” Submersible, Enclosed Impeller (Class 1, Div.1, Groups C & D Hazardous Location 'Explosion-Proof')

Model KFG(X)2 - 4” Submersible, Recessed Impeller Pump

by Keen Pump Co. Inc.     based in Ashland, OHIO (USA)

4” Submersible, Recessed Impeller (Class 1, Div.1, Groups C & D Hazardous Location 'Explosion-Proof')

Model 2CM 25/130A - Twin Impeller Centrifugal Pump

by Speroni S.p.A.     Distributor in GEORGIA (US) (USA)

Twin impeller centrifugal water pumps to lift clean water and non-aggressive liquids. The main feature are the two opposite impellers which allow higher lifts than in the single-impeller model. They are qualified for civil and industrial fittings, for water distribution by tank pressure groups and for irrigation in gardening and agricolture.

TORUS - Recessed Impeller Vortex Pumps

by Eco-Tech, Inc.     based in Canton, GEORGIA (US) (USA)

A severe duty pump for fluids containing large solids, abrasives, delicate crystals, fibers, and stringy materials. The impeller is completely recessed within the pump, minimizing contact with the process fluid and allowing clear passage of solids without clogging.

Hayward Gordon Torus - Recessed Impeller Vortex Pumps

by Hayward Gordon Ltd.     Distributor in GEORGIA (US) (USA)

A severe duty pump for fluids containing large solids, abrasives, delicate crystals, fibers, and stringy materials. The impeller is completely recessed within the pump, minimizing contact with the process fluid and allowing clear passage of solids without clogging.

Model MPO - Open Impeller Centrifugal Pumps

by Memphis Pump & Mfg. Co. Inc     based in Memphis, TENNESSEE (USA)

Memphis' Open Impeller Centrifugal Pumps are excellent for general duty uses, within the parameters of head and volume for the different models, but they are especially suitable for pumping granular solutions. The open impellers will pass spheres up to 5/16', which enables these pumps to pump slurries, wettable powers and liquids containing clots ...

Model 7071 Series - Horizontal Open Impeller Centrifugal Pump

by Gusher Pumps     based in Williamstown, KENTUCKY (USA)

The 7071 Series is a horizontal, open impeller centrifugal pump that meets the specifications of ANSI B-73.1. The series consists of 3 Power Frames and 33 pump sizes.

Model HPG200 - 2 HP Centrifugal Grinder Semi Open Impeller Pump

by Hydromatic pump     based in Ashland, OHIO (USA)

Engineered for low pressure sewer system applications. Semi-open impeller provides steep non-overloading operating curve. Durable motor will deliver many years of reliable service. Oil-filled motor for maximum heat dissipation and constant bearing lubrication. Exclusive dual cutter design cuts solids to the smallest particle size. High torque ...

Need help finding the right suppliers?

Let the XPRTs do the work for you