Air Monitoring Standards Books

  • The Economics of Climate Change Policies

    The protection of the earth's atmosphere requires substantial efforts to reduce CO2 and other greenhouse gas emissions. In order to meet these targets, governments have started to implement climate policies which include informational measures such as demonstration programmes as well as economic instruments such as energy or emission taxes, ...

  • API STD 685 For Petroleum Refining Standards

    This standard covers the minimum requirements for sealless centrifugal pumps for use in petroleum, heavy duty chemical and gas industry services. Refer to Appendix U for application information.Note: A bullet (•) at the beginning of a paragraph indicates that either a decision or further information is required. Further ...

  • ASTM Standards For Fire Hazards In Oxygen Systems

    Twenty-three ASTM standards address fire hazards in oxygen systems, including safe practices in design, materials selection, storage, handling, and operations.This is a vital resource for those involved in the production or use of liquid or gaseous oxygen or oxygen-enriched gas mixtures, including engineers, scientist, technicians, purchasing ...

  • API STD 610 For Petroleum Refining Standards

    This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services.This International Standard is applicable to overhung pumps, between-bearings pumps and vertically-suspended pumps (see Table 1). ...

  • API RP 74 Standard for Exploration & Production

    These recommendations apply to production operations as deÞned herein. For information on drilling, well servicing and workover operations, see API RP 54.PurposeThe purpose of this document is to recommend practices and procedures for promotion and maintenance of safe working conditions for personnel engaged in onshore oil and gas ...

  • API RP 14FZ Standard for Exploration & Production

    This document recommends minimum requirements and guidelines for the design and installation of electrical systems on fixed and floating petroleum facilities located offshore when hazardous locations are classified as Zone 0, Zone 1, or Zone 2. For facilities classified as Division 1 or Division 2, reference API RP14F, Recommended Practice for ...

  • Metals -- Mechanical Testing; Elevated and Low-Temperature Tests; Metallography

    Includes tests and practices that outline the standard procedures needed to perform mechanical testing, including: machine calibration, bend and flexure testing, compression, ductility and formability, elastic properties, impact, linear thermal expansion, shear and torsion, residual stress, tension testing, structural films for MEMS, and ...

  • API STD 662 PART 1 For Petroleum Refining Standards

    This part of ISO 15547 gives requirements and recommendations for the mechanical design, materials selection, fabrication, inspection, testing, and preparation for shipment of plate-and-frame heat exchangers for use in petroleum, petrochemical and natural gas industries. It is applicable to gasketed, semi-welded and welded plate-and-frame heat ...

  • Boiler Mact Emissions Limits

    Industry is looking for new fuels that can replace coal, oil and natural gas. This free EBook takes a look at some of the technical and regulatory challenges involved in developing alternative fuel ...

  • API SPEC 5DP Standard for Exploration & Production

    This International Standard specifies the technical delivery conditions for steel drill-pipes with upset pipe-body ends and weld-on tool joints for use in drilling and production operations in petroleum and natural gas industries for three product specification levels (PSL-1, PSL-2 and PSL-3). The requirements for PSL-1 form the basis of this ...

  • Manual on Requirements, Handling, and Quality Control of Gas Turbine Fuel

    The Symposium on Gas Turbine Fuel Requirements, Handling and Quality Control was presented at the Seventy-fifth Annual Meeting of the American Society for Testing and Materials held in Los Angeles, Calif., 25—30 June 1972. The symposium was sponsored by Committee D02 on Petroleum Products and Lubricants, Technical Division D02.C on Turbine ...

  • API STD 613 For Petroleum Refining Standards

    This standard covers the minimum requirements for special-purpose, enclosed, precision single- and double-helical one- and two-stage speed increasers and reducers of parallelshaft design for petroleum, chemical and gas industry services. This standard is primarily intended for gear units that are in continuous service without installed spare ...

  • API SPEC 12K Standard for Exploration & Production

    This specification covers minimum requirements for the design, fabrication, and shop testing of oilfield indirect type fired heaters used in the production of oil, gas, and their associated fluids. They are usually located at some point on the producing flow-line between the wellhead and pipeline. Heater components covered by this specification ...

  • API STD 602 For Petroleum Refining Standards

    This international standard specifies the requirements for a series of compact steel gate, globe and check valves for petroleum and natural gas industry applications.It is applicable to valves of:— nominal pipe sizes NPS 1/4, NPS 3/8, NPS 1/2, NPS 3/4, NPS 1, NPS 1 1/4, NPS 1 1/2, NPS 2, NPS 2 1/2, NPS 3, and NPS ...

  • Adjunct to D6512 Standard Practice for Interlaboratory Quantitation Estimate

    DQCALC® Software: Outlier Removal, Laboratory Detection, and Quantitation EstimatesThis is a 22-page manual with CD-ROM of an application developed in early 2004 to help users automate the procedures of three ASTM standards: D 2777-Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on WaterD ...

  • API RP 11V2 Standard for Exploration & Production

    Test site recommendations (Section 3): This section outlines the equipment needed for testing valves to determine the following:Valve flow coefficients (Cv).Pressure drop ratio factor (Xt).Gas-lift valve performance curves.Gas-lift valve probe tests (Section 4): This test method is outlined for determining the stem travel as pressure is ...

  • API RP 64 Standard for Exploration & Production

    PurposeThis recommended practice (RP) is intended to provide accurate information that can serve as a guide for selection, installation, testing, and operation of diverter equipment systems on land and marine drilling rigs (barge, platform, bottom-supported, and floating). Diverter systems are composed of all subsystems required to operate the ...

  • API SPEC 17J Standard for Exploration & Production

    1 Scope1.1 Purpose1.1.1 This specification defines the technical requirements for safe, dimensionally and functionally interchangeable flexible pipes that are designed and manufactured to uniform standards and criteria.1.2 Minimum requirements are specified for the design, material selection, manufacture, testing, marking, and packaging of ...

  • Adjunct to D6091 Standard Practice for 99%/95% Interlaboratory Detection Estimate (IDE) for Analytical Methods with Negligible Calibration Error

    DQCALC® Software: Outlier Removal, Laboratory Detection, and Quantitation EstimatesThis is a 22-page manual with CD-ROM of an application developed in early 2004 to help users automate the procedures of three ASTM standards: D 2777-Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on WaterD ...

  • API STD 619 For Petroleum Refining Standards

    This standard covers the minimum requirements for dry and oil-flooded helical lobe rotary compressors (see Figure 1) used for vacuum or pressure or both in petroleum, petrochemical, and natural gas industries. It is intended for compressors that are in special-purpose applications. It does not cover general purpose air compressors, liquid ring ...

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you