Only show results available in Virginia? Ok

Air Toxics Applications

  • Painting & Coating

    Paint fumes are Unbreathable. Spray Painting VOCs and Powder Coating dust are both harmful pollutants which are produced during painting operations. The volatile organic compounds (VOCs) emitted from paint can cause respiratory issues and require proper ventilation to remove harmful gasses from the work area. Powder Coating lines and spray painting produce dangerous fumes and dusts which need to be filtered or exhausted outside your facility. Industrial coatings and chemicals can produce toxic VOCs and foul odors which can effect worker`s health and reduce productivity. Some of the most common coatings are polymers which include polyurethane, epoxy and moisture-cure urethane. Many different industries required the use of glues, adhesives, solvents and different chemical agents in their production process, but are unsure of the best way to handle this nuisance. Exhausting fumes outside may be an option when VOCs are extremely dangerous and odorous but companies must also comply with EPA guidelines which regulate which gases can be emitted. In cold climates and in air-conditioned facilities, capturing, filtering and recirculating fumes can provide huge energy savings preventing costly heat loss and energy intensive air makeup systems. Utilizing activated carbon granules can allow operators to filter VOCs and odors from painting and cutting applications. Different quantities and types of carbon modules are required depending upon the contaminant. Contact Diversitech with an MSDS sheet detailing your chemical`s characteristics for an evaluation of your workplace air quality problem.?

    By DiversiTech based in Montreal, QUEBEC (CANADA).

  • Integrated real-time gas analysis solution for emissions industry

    Pollutant emissions from industrial smoke stacks are a major national concern due to both health concerns and climate change. As a consequence, there are at least tens of gas analyzer manufacturers in the U.S. alone that compete in that market and have done so for years. What CIC Photonics brings to that competitive field is its expertise derived from its Combustion Efficiency Solution and its high performance IRGAS Systems. The IRGAS-CEM provides real-time and simultaneous measurements of the multitude of toxic combustion products, including CO, CO2, NOx, SOx, CH4, CxHy, H2S, etc. The EP-IRGAS-SPA is also applicable for fast time responses.

    By CIC Photonics, Inc. based in Albuquerque, NEW MEXICO (USA).

  • Premium

    Measurement solution for accurate continuous formaldehyde measurement formaldehyde in emissions and ambient air applications

    Formaldehyde (HCHO) is the simplest aldehyde species and is present, or generated by, many sources (both natural and industrial). It is classed as a substance that is toxic and harmful to human health.

    By Protea Limited based in Middlewich, UNITED KINGDOM.

  • Premium

    Waste water treatment plants Air quality control by TRS MEDOR Online Odor Monitoring

    ontext & Challenges Globally, the wastewater treatment is the first public health issue. Urban development leads to urbanization near waste water treatment plant and extension of sewerage network. These aspects induce to an augmentation of sulfur compounds (H2S, mercaptans and sulfides) which are very corrosive, odorant and toxic. To monitor this compounds online CHROMATOTEC® offers high meteorological solutions. Odors are very distinct air contaminants as they generate nuisances. The factors playing a role in the determination of odor annoyance are: odor concentration and intensity, frequency, appreciation, duration, synergy and location. CHROMATOTEC® proposes an automatic solution to well identify the origin and the level of odors.

    By Chromatotec Group based in Val de Virvée, FRANCE.

  • Air monitoring equipments for outdoor & indoor air quality

    Gradko’s ambient air monitoring equipment is widely used to monitor both indoor and outdoor air quality. Continuous development allows us to provide equipment for a broad range of applications, covering short-term and long-term monitoring. Pollutants can be detected even at very low levels – limits of detection are typically in the low parts per billion (ppb) range.

    By Gradko International Ltd based in Winchester, UNITED KINGDOM.

  • Premium

    Portable Stack Monitoring

    Many industries are required to measure stack emissions of toxic gases periodically, but not continuously. Extractive wet chemical methods currently used are slow, labor intensive and expensive. A single GasFinderFC can perform stack monitoring requirements for a specific gas, quickly, easily and accurately.

    By Boreal Laser Inc. based in Edmonton, ALBERTA (CANADA).

  • Waste gas treatment for the semiconductor industry

    In the early 1990s no appropriate and comprehensive technical solution had been available for waste gas treatment in the semiconductor industry. Back then as well as today many industrial and research production procedures use process gases and generate waste gases. These waste gases, considered greenhouse gases, are toxic and/or highly flammable and very often pose a significant risk to production facilities and the environment. The semiconductor industry, for instance, uses perfluorocarbons, whose global warming potential is extremely high and therefore requires an efficient waste gas treatment. Combining and transporting different gases into a fab’s central waste gas system might produce highly flammable and highly explosive gaseous mixtures, which in the past has occasionally caused the total loss of entire production facilities. Particles contained within gases may also cause exhaust blockages. To eliminate these risks, process waste gases need to be treated at the “Point-of-Use” (POU) where harmful exhausts are abated immediately.

    By DAS Environmental Expert GmbH based in Dresden, GERMANY.

  • Premium

    Air pollution control for the printing, laminating & converting industry

    Achieving cost effective local regulatory compliance in the printing and converting industry requires a complete understanding of both regulatory standards and the printing process. Through experience, Anguil has developed unparalleled expertise in meeting your unique requirements. We understand the effects of water versus solvent-based inks on the line, elimination of odors and toxic fumes from dryers and oven tunnel exhausts, and the capture of fugitive emissions. Over 300 successful printing installations worldwide, in plants just like yours, have shown Anguil to be a Proven Solutions Provider.

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Mercury monitoring for on-site remediation

    Fugitive emissions can be a health concern during removal and disposal of mercury-contaminated material at remediation sites. Thus, remediation projects either indoors or outdoors often require on-site, real-time mercury air monitoring with a Tekran 2537. This assures permitted levels are not exceeded during waste processing and human exposure levels are below government regulated toxicity thresholds. Often multiple sites must be monitored continuously. The Tekran 1115 Multi-Port Sampler is the ideal tool for multiplexing the Tekran 2537 for real-time continuous on-site monitoring of mercury fugitive emissions. Please contact us for more information on mercury remediation monitoring.

    By Tekran Instruments Corporation based in Knoxville, TENNESSEE (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you