Only show results available in Virginia? Ok

Climate Change Applications

  • Premium

    Air pollution control for ventilation air methane industry

    Ventilation Air Methane (VAM) is a Greenhouse Gas (GHG) released by coal or mineral mining operations, it is also commonly known as Coal Mine Methane (CMM).  The air pollutants from this process have a global warming potential 21 times greater than carbon dioxide, which is another well known GHG.  As alternative energy technologies have developed, methane is increasingly used to generate electricity and heat.  Landfills and mines represent two of the most abundant sources, however reports indicate that more than 50% of all VAM is exhausted from mine ventilation systems and remains unutilized.

    By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

  • Premium

    Capabilities of the Adsorbent Tube Injector System (ATIS™)

    The Adsorbent Tube Injector System (ATIS) was developed at Supelco® by R&D Scientists, as a tool to assist in our comprehensive adsorbent research for thermal desorption tubes. The ATIS provides an efficient means of transferring calibration standards in either the gas or liquid phase onto the adsorbent packed tubes. The ATIS employs the technique of flash vaporization to vaporize the sample in a continuous flow of inert gas; the inert gas carries the sample to the tube. The sample pathway of the ATIS is constructed of glass and stainless steel. The calibration standard is injected by a syringe through a replaceable septum in the center of the injection glassware, which is heated. After enough time has elapsed, typically less than five minutes, the tube is removed from the ATIS and analyzed using the appropriate analytical technique for that adsorbent tube.

    By MilliporeSigma based in Bellefonte, PENNSYLVANIA (USA).

  • Premium

    Gas monitoring instruments and systems for greenhouse gas emissions from soil

    Measurement of greenhouse gases released from soil and water surface forms an important part of climate change study. Microbial activity in the soil or for instance the melting of permafrost releases greenhouse gases such as Methane and nitrous oxide N2O into the atmosphere. Measurement of the concentration for these gases inside an open-bottom soil chamber placed on the soil over time tells the emission rate (flux) per chamber footprint area.

    By Gasmet Technologies Oy based in Helsinki, FINLAND.

  • Premium

    Compressed air measurement & control flow solutions

    Compressed air isn`t free, so more and more companies carefully monitor its usage. Thermal flow meters are ideal for this application. Because our thermal flow meters measure mass flow directly, no temperature or pressure compensation is required. Thermal flow meters also have a very high turndown, allowing the same flow meter to measure very low leak rates as well as full operational flows.

    By Sierra Instruments, Inc. based in Monterey, CALIFORNIA (USA).

  • Premium

    radiello™ Passive Sampler as a Tool for the Measurement of Atmospheric Ammonia Concentrations and Dry Deposition

    The radiello ammonia sampler impregnated with phosphoric acid represents a low-cost, reliable and simple tool for assessing the atmospheric deposition of ammonia at parts per billion (ppb) concentration levels.

    By MilliporeSigma based in Bellefonte, PENNSYLVANIA (USA).

  • Premium

    Formaldehyde and Acetaldehyde Determination in Air Using Fully Automated On-Line Desorption and Analysis of DNPH Cartridges

    Airborne aldehydes and ketones are collected by passing air through a cartridge containing 2,4-dinitrophenylhydrazine (DNPH). Carbonyl compounds react with the DNPH to form hydrazones, which are immobilized on the cartridge. These compounds can be easily eluted from the cartridge with acetonitrile and analyzed by HPLC with UV detection. Traditionally, this analysis including the workup contains a series of manual steps, which can become time-consuming and could incur experimental error. Automating the extraction of LpDNPH S10 cartridges and putting it in-line with the HPLC analysis will significantly reduce manual labor using this technique and this will improve reproducibility of the method by reducing potential experimental errors by the operator. The automation and unattended operation of the method leads to high throughput for determining airborne formaldehyde and acetaldehyde.

    By MilliporeSigma based in Bellefonte, PENNSYLVANIA (USA).

  • Premium

    Carbon footprinting calculations for environmental management

    With its expertise in calculating and managing emissions data, CERC offers a range of services to assess greenhouse gas emissions, from determining the carbon footprint of a single industrial process, to compiling a greenhouse gas inventory for a whole geographical area.

    CERC uses methods and emission factors laid out by the Intergovernmental Panel on Climate Change (IPCC). Emissions from transport, industrial, heating and agricultural activities are calculated and stored using the EMIT software package.

    By Cambridge Environmental Research Consultants (CERC) based in Cambridge, UNITED KINGDOM.

  • Premium

    Benzene Monitoring

    Cerex Monitoring Solutions manufactures UVDOAS analyzers for a variety of Benzene monitoring applications. As benzene specific single gas or multi-gas analyzers, our instruments are available with application specific detection ranges and fully configurable alarm functionality.

    By Cerex Monitoring Solutions, LLC. based in Atlanta, GEORGIA (US) (USA).

  • Premium

    Emissions Monitoring for Chemical Plants

    The Opsis gas monitoring system is designed for monitoring in stacks and gas ducts in chemical industries, both in order to increase plant efficiency and to monitor emissions. The Opsis systems have been internationally approved by e.g. the German TÜV and the U.S. EPA.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    O2 Monitoring in Air

    Oxygen (O2) is a colorless odorless gas, essential to all life on Earth but damaging in high concentrations. An O2 analyzer should thus be employed for safety management and air pollution prevention purposes. LasIR MP110 is perfect for continuous emission monitoring of O2. It is based on TDLAS technology and can be calibrated as an O2 analyzer, providing accurate and reliable measurements. It quickly responds to changes in compound concentration, thus providing continuous emission monitoring for the specified gas.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

  • Premium

    Laser gas detection for research

    Axetris laser gas detection OEM modules are used in a variety of research applications: Climate Change Research, Environmental Research.

    By Axetris Ag based in Kaegiswil, SWITZERLAND.

  • Premium

    Air Quality Monitoring Stations

    Opsis provides complete AQM stations, used for street-level, urban trend and background applications. The monitoring systems have been approved by the German TÜV and the U.S. EPA among others.

    By Opsis AB based in Furulund, SWEDEN.

  • Premium

    Meteorological Sensors for Wind Turbine Control Industy

    Higher, more robust, more reliable: Parallel to the growing requirements for wind turbines, the requirements for monitoring sensors grow as well. But how can wind sensor manufacturers fulfil these wishes? The ideal sensor has both a high degree of precision and a long, maintenance-free useful life under the most extreme of conditions. While mechanical anemometers were initially used in turbines, most producers around the world have since switched to ultrasonic anemometers without moving parts as part of their standard equipment. We have different ultrasonic wind sensors with open protocols / interfaces, which allows an easy exchange of old mechanical wind sensors trough state-of-the-art ultrasonic anemometers on your wind turbine.

    By G. Lufft Mess- und Regeltechnik GmbH based in Fellbach, GERMANY.

  • Premium

    Negative Pressure Environment

    Negative pressure containment is an industry standard method of capturing fine dust particles and mold spores that are inevitably released during mold abatement and restoration projects. Ensuring your contained area has the required air changes (ACH) and that the air is adequately scrubbed is where you will find the competitive advantage of our OmniAire line of HEPA Air Filtration Machines. With standard airflows ranging from 50 to 18000 CFM, OmniAire Air Filtration Machines can provide the necessary ACH for any size project. Maintaining adequately pressurized containment, air changes per hour, and HEPA efficiency are all important to your overall project management needs.

    By Omnitec Design, Inc. based in Mukilteo, WASHINGTON (USA).

  • Premium

    Pressure Monitor use in a Containment Area

    When using negative pressure containment, it is important to monitor the pressure inside the containment in reference to the outside area. However, because the typical negative pressure required is usually only 0.020”WC, it can be difficult to find equipment sensitive enough to measure and monitor your containment area. Omnitec Design has two options to meet this need. Both the Watchman Differential Pressure Monitor and the self-contained Omniguard 4 Pressure Recorder are designed to provide highly accurate monitoring and alarm functions while still being easy to setup with a simple push-button calibration. A pressure monitor is a very important tool that can help ensure the integrity of a containment. Dealing with hazardous debris from abatement/remediation jobs can be a sensitive task that demands safe practices by workers to guarantee their safety, and those who may come into contact with potentially harmful material.

    By Omnitec Design, Inc. based in Mukilteo, WASHINGTON (USA).

  • Premium

    SO2 Monitoring in Air

    SO2 (sulfur dioxide) is measured in a number of applications. SO2 is used as a food grade preservative and must be regulated in accordance with government-set criteria to be safe for consumers. It is also measured in fuel exhaust to control for environmental pollution and in cement plants for process control.

    By Unisearch Associates Inc. based in Concord, ONTARIO (CANADA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you