What is a Lubricant?
A lubricant is a material that reduces the friction between two surfaces making it easier for them to move across each other. Lubricity measures the reduction of friction that results from using a lubricant. A higher percentage of lubricity indicates a greater reduction of force.
Dry force is the amount of force required to insert a part without using a lubricant. Lubricated force is the amount of force required to insert a part after applying a lubricant. A force gauge meter can be used to measure the force (in newtons) needed to insert a part.
A lubricant should be used any time you need to decrease the friction between two surfaces.
10 Things To Know When Choosing An Assembly Lubricant 1. Temporary or Permanent Lubrication?
Some lubricants provide ongoing lubrication to keep parts moving over and over again. Machinery that consists of parts that must continually move or slide across each other will benefit from using a permanent lubricant to ensure they are operating properly.
Other lubricants provide temporary lubrication, reducing the friction between two parts for a short amount of time. After drying, the lubricity provided by a temporary lubricant is gone and the two parts will no longer slide easily across each other. Temporary lubricants are used for assembly and repair applications.
Rubber materials, in particular, are extremely slip-resistant, making them inherently difficult to install, remove, or otherwise manipulate – even when wet. This creates a challenge during the assembly and repair of rubber parts that can result in problems such as ill-fitting, misaligned or damaged parts, rolling O-rings, uneven cuts or worker injury. Temporary assembly lubricants can help prevent these problems.
2. How Much Lubrication Do You Need?
Sometimes you need a lot of lubrication, sometimes just a bit. Different lubricants will reduce friction by varying amounts depending upon their viscosity. Find a formula that is right for your application.
3. What are the Advantages of Temporary Assembly Lubricants? Reduce Installation Force:
A thin film of lubricant applied to a part fills in any gaps, holes, or spaces between two separate surfaces, allowing them to slide across each other. By reducing the surface tension between the two surfaces, rubber parts can slide into place easily.
Design Parts with Better Tolerances:
When a lubricant is included in the design control process, mated parts can have lower tolerances because the characteristics of the lubricant are considered. Partnering with a lubrication engineer ensures the optimal lubricant is selected before production goes live.
Improve Product Performance:
Improper part alignment can lead to part failure and safety issues. Taking into consideration lubrication properties like dry time, material compatibility, any interfering residue and environmental conditions, will ensure that mated parts will work as anticipated.
Increase Production Rates:
Paring the optimal lubricant with the right application technique speeds up production.
Help to Avoid Worker Injuries:
Assembly lubricants ease the installation process of many parts. An increase in lubricity, even by small amounts, is greatly appreciated by line operators required to maintain strict cycle times. Inferior lubrication quickly leads to fatigue, muscle strain, injuries and lost work time.
4. What is the Dry Time of Your Temporary Lubricant?
Some temporary lubricants dry quickly while others take longer to fully dry.
Quick drying lubricants are frequently used in assembly applications in which the parts undergo pressure testing or movement shortly after assembly. In these cases, it’s important to have the part firmly in place before the next step in the assembly process.
Other assembly applications may take longer or the parts may need to be manipulated a few times before the assembly is complete. In these instances, you may benefit from a slower drying temporary lubricant.
Yet, in other assembly operations, achieving maximum lubrication may be the primary goal and the dry time of the lubricant is less important.
Manufacturers of temporary assembly lubricants should be able to advise you about methods of slightly altering the dry time of their lubricants based upon the amount applied, the method of application, part tolerance, material porosity, and temperature.
5. Can Temporary Lubricants be Used With All Types Of Surfaces?
It’s important to check the compatibility of any chemicals that will come in contact with your parts and equipment. What types of surfaces are they made of? Ask the lubricant manufacturer if their product is compatible with the specific type of rubber, metal and/or plastic found in your parts and equipment.
Lubricants will be absorbed more quickly by porous rubbers, like Buna-N and EPDM, than by plastics and coated rubbers. You may want to choose a quicker drying formula for less porous surfaces.
6. How Will You Apply the Lubricant?
Think about your assembly process and the parts that will need a temporary lubricant. What type of application method will work best for your unique process? Common methods of application include dunking and dipping parts, using brushes, sponges and sprays, and using automated solutions. Make sure the lubricant you choose will work well with the best application method for your unique situation.
7. Can They be Used for Food Manufacturing Equipment?
Food and beverage manufacturing is a highly regulated industry. Therefore, all parts and processes, including any lubricants that are used, must comply with federal regulations and industry standards. Look for specially formulated assembly lubricants that are registered with the NSF as H1 lubricants approved for incidental food contact applications.
8. Are They Safe?
Avoid using lubricants that can cause rubber parts to swell or dry out, like alcohol or petroleum-based products. Look for a product that is compatible with the parts it will come in contact with.
Be sure to also consider the environmental impact of any lubricants you are using. Look for products that are non-hazardous and non-flammable, making them safe for workers and the environment. Many assembly lubricants are biodegradable.
Choose an assembly lubricant that will work well, yet meet all of your safety requirements and federal regulations.
9. Is it Possible to Arrange a Trial?
Many lubricant manufacturers will offer free samples for testing. Testing enables you to run trials for your unique assembly application and choose the product that will best meet your needs.
10. Will the Manufacturer Offer Support?
In addition to their willingness to offer free product samples for testing, look for a supplier that can offer technical guidance and provide a variety of products to solve your assembly requirements. The manufacturer should be able to assist you by providing material compatibility studies, insertion force measurement testing, toxicology reports, regulatory compliance, free product samples, and technical support.
With careful thought and planning, you can find a lubricant that meets all of your specifications. When choosing a lubricant for your assembly application consider the amount of lubricity required, surface compatibility, dry time, application methods, chemical composition and safety of the product.