1. da130-01

01-12-2009 130 I1 01 EpH - ORPIMMERSION PROBE9336pH130-01/1130- Electrode holder and protection - Easy calibration: buffer flask grips on - Flange or PE collar fitting - For any KCl gel type electrodes - For PG 13.5 electrode threaded connection - PVC, PPH or stainless steel construction - Wire outlet through a PG 9 APPLICATIONSThis immersion probe 9336 is convenient for all pH or ORP measurementsin tank, drain, basin, open channel.Standard construction is of with grey PVC parts and a red PVC tube. The electrode holder in PVC or PPh is specially designed to avoid electrodedamage during calibration. Electrode protection end is removed from theholder; the buffer flask (buffers 9011/ 9012/ 9013/ 9015) is then gripped onthe holder during the entire calibration step. There is no need to hold theprobe during these operations, it can stand on floor. CODE NUMBERS AND REFERENCESCode Reference Designation130 150 9336 PVC PVC 1 m long probe for one electrode 130 250 9336 PPH PPh 1 m long probe for one electrode 131 150 9336 SS 316L Stainless steel 1 m long probe for one electrode 130 112 9358 PE ND50 PE flange, dip length adjustment for 9336 130 113 9337/ PPh PPh bucket + PVC probe 9336TECHNICAL FEATURESImmersion height: Standard length 1000 mm(from 200 to 3000 mm on request)Construction: PVC, PPH, or Stainless steel 316 LHousing: PBT glass fiber reinforced – IP 65Cable output: PG 9 Mounting: With PE DN50 flange 9358; for dip adjustment or PE collar, 50 mm diameter Maximal pressure: 4 bar / PVC and PPH16 bar / Stainless steel Maximal temperature: 55 °C / PVC100 °C / PPH135 °C / Stainless steel 316 LMaximal pressure and temperature depend of mounted electrode. Pressure and temperature value are not for simultaneous conditions. ELECTRODESAssociated electrodes for our pH and ORP products are described on thedocumentation N° 150-01. Only electrodes with sealing by Pg 13.5 thread could be mounted on ourprobes. pH - ORP IMMERSION PROBE9336pH - ORPIMMERSION PROBE9336pH130-01/213001-12-2009 130 I1 01 E130ELECTRODE MOUNTINGIntroduce the pH measurement cable 9060 (1) through thecable gland and probe head (2). A cable length of probe lengthplus 20 cm would be necessary. Mount, connect and weld on the connector 9054 (3) to the cable(see documentation pH160 – msa160-9054). Check the O' ring (4) is on place. Screw the probe head (2) on extension tube (5). Ensure that the connector goes out from the tube. Install the pH or ORP electrode (6) on the holder (7). Check the O' ring (8) is on place. Screw tightly the connector on the electrode. Pull smoothly the cable from through the cable gland, in order tohave the electrode holder (7) close to the extension tube. The cable must not be stretched inside the tube. Screw the nut (9) keeping the holder (to protect the cable) in itsposition. Tight firmly this nut by hand, not excessively. Prevent the electrode holder to rotate during this operation. Screw tightly the cable gland on the head. Rotate the head in the good position and block it with the twoscrews (11)ELECTRODE DISMOUNTINGTo dismantle the electrode, proceed as above on reverse steps.Careful not to loose the O' ring. CALIBRATIONYou may find detailed all instructions in the instruction manuals ofpH or ORP meters. Unscrew the electrode protection end (10). Clean up theelectrode with water (do not wrap it with paper neither tissue).Adapt the buffer flask on the holder (7). The flask grips on it, the probe can lay down the floor. Ending the calibration sequences, screw in the electrodeprotection and lock it smoothly. Type DN F M D N (x4) E C A9358 50 163 125 10 Ø 18 52 95 143Standard length: 1000 mm