434 4113 Brochure

Core 434/4113 EN 1.4113, ASTM 434 / UNS S43400 Products & dimensions Cold rolled products available dimensions in mm General characteristics Outokumpu Core 434/4113 is a 1% molybdenumOutokumpu Core 434/4113 is a 1% molybdenum--alloyed alloyed ferritic stainless steel with medium chromium and normal ferritic stainless steel with medium chromium and normal carbon content, which can be used in many corrosive carbon content, which can be used in many corrosive environments, such as at the cold end of automotive exhaust environments, such as at the cold end of automotive exhaust systems. After tensile elongation, Core 434/4113 may be prone systems. After tensile elongation, Core 434/4113 may be prone to the ridgingto the ridging--surface phenomenon.surface phenomenon.   Typical applications l Automotive trim fittingsAutomotive trim fittings Coil / Strip Plate / SheetSurface finish Thickness Width Thickness Width2B2B Cold rolled, heat treated, pickled, skin passedCold rolled, heat treated, pickled, skin passed 0,200,20--3,583,58 1212--15241524 0,250,25--3,583,58 1818--152415242BB2BB 2BB Bright2BB Bright--pickledpickled 0,200,20--3,503,50 3030--15001500 0,250,25--3,503,50 500500--150015002C2C Cold rolled, heat treatedCold rolled, heat treated 0,800,80--3,503,50 3030--153015302D2D Cold rolled, heat treated, pickledCold rolled, heat treated, pickled 0,200,20--3,003,00 3030--13201320 0,250,25--3,503,50 500500--150015002E2E Cold rolled, heat treated, mech. desc. pickledCold rolled, heat treated, mech. desc. pickled 0,330,33--3,583,58 1212--15301530 0,330,33--3,583,58 1818--152415242F2F 2F Cold rolled, heat treated,2F Cold rolled, heat treated, skin passed skin passed 0,330,33--3,583,58 1212--15241524 0,330,33--3,583,58 1818--152415242G2G GroundGround 0,300,30--3,583,58 1212--15301530 0,300,30--3,583,58 1818--153015302H2H Work hardenedWork hardened 0,200,20--2,002,00 5050--13201320 0,250,25--2,002,00 500500--132013202J2J Brushed or dull polishedBrushed or dull polished 0,300,30--3,003,00 3030--15301530 0,300,30--3,503,50 500500--153015302K2K Satin finishSatin finish 0,530,53--3,583,58 1212--15241524 0,530,53--3,583,58 1818--152415242M2M PatternedPatterned 0,300,30--2,002,00 3030--13201320 0,500,50--3,503,50 500500--150015002R2R Cold rolled, bright annealedCold rolled, bright annealed 0,050,05--3,503,50 33--15001500 0,250,25--3,503,50 1818--150015001 - Outokumpu 4113 Printed: 23 jun 2015    Continous Hot rolled products available dimensions in mm Chemical composition The typical chemical composition for this grade is given in the table below, together with composition limits given for theThe typical chemical composition for this grade is given in the table below, together with composition limits given for the product product according to different standards. The required standard will be fully met as specified on the order.according to different standards. The required standard will be fully met as specified on the order. The chemical composition is given as % by mass.The chemical composition is given as % by mass. Corrosion resistance Outokumpu Core 434/4113 has good corrosion resistance in solutions of many halogenOutokumpu Core 434/4113 has good corrosion resistance in solutions of many halogen--free organic and inorganic compounds over a free organic and inorganic compounds over a wide temperature and concentration range. It can withstand many sufficiently diluted organic and mineral acids depending on the wide temperature and concentration range. It can withstand many sufficiently diluted organic and mineral acids depending on the temperature and concentration of the solution. Core 434/4113 may suffer from uniform corrosion in strong organic and mineral acids, as temperature and concentration of the solution. Core 434/4113 may suffer from uniform corrosion in strong organic and mineral acids, as well as in hot concentrated alkaline solutions. If sensitized for intergranular corrosion due to welding or an inappropriate heat treatment, well as in hot concentrated alkaline solutions. If sensitized for intergranular corrosion due to welding or an inappropriate heat treatment, corrosion rates in certain environments may be significantly higher.corrosion rates in certain environments may be significantly higher. In aqueous solutions containing halogenides, e.g. chlorides or bromides, pitting and crevice corrosion may occur depending on the In aqueous solutions containing halogenides, e.g. chlorides or bromides, pitting and crevice corrosion may occur depending on the halogenide concentration, temperature, pHhalogenide concentration, temperature, pH--value, concentration of oxidizing compounds, or crevice geometry, if applicable. The presence value, concentration of oxidizing compounds, or crevice geometry, if applicable. The presence of corrosion inhibiting or accelerating compounds like e.g. transition metal ions or organic compounds may influence the corrosion of corrosion inhibiting or accelerating compounds like e.g. transition metal ions or organic compounds may influence the corrosion behavior of Core 434/4113. Due to its ferritic crystal structure, Core 434/4113 is not prone to chloridebehavior of Core 434/4113. Due to its ferritic crystal structure, Core 434/4113 is not prone to chloride--induced stress corrosion induced stress corrosion cracking.cracking. Core 434/4113 can be used for indoor and outdoor applications in rural areas and urban environments where chloride contamination is Core 434/4113 can be used for indoor and outdoor applications in rural areas and urban environments where chloride contamination is low. The best material performance is typically achieved with the help of adequate design, correct postlow. The best material performance is typically achieved with the help of adequate design, correct post--weld treatment and regular weld treatment and regular cleaning during use (if applicable).cleaning during use (if applicable). The maximum service temperature of Core 434/4113 in dry air is 800 °C. The presence of other corrosive compounds in the hot The maximum service temperature of Core 434/4113 in dry air is 800 °C. The presence of other corrosive compounds in the hot environment like water or sulfur compounds may reduce the maximum service temperature significantly.environment like water or sulfur compounds may reduce the maximum service temperature significantly. For more information on corrosion resistance, please refer to the Outokumpu Corrosion Handbook or contact the our experts.For more information on corrosion resistance, please refer to the Outokumpu Corrosion Handbook or contact the our experts. Pitting Resistance Equivalent (PRE) is calculated using the following formula: PRE = %Cr + 3.3 x %Mo + 16 x %NPitting Resistance Equivalent (PRE) is calculated using the following formula: PRE = %Cr + 3.3 x %Mo + 16 x %N Corrosion Pitting Temperature (CPT) as measured in the Avesta Cell (ASTM G 150), in a 1M NaCl solution (35,000 ppm or mg/l chloride Corrosion Pitting Temperature (CPT) as measured in the Avesta Cell (ASTM G 150), in a 1M NaCl solution (35,000 ppm or mg/l chloride ions).ions). Critical Crevice Corrosion Temperature (CCT) is obtained by laboratory tests according to ASTM G 48 Method FCritical Crevice Corrosion Temperature (CCT) is obtained by laboratory tests according to ASTM G 48 Method F Coil / Strip Plate / SheetSurface finish Thickness Width Thickness Width1C1C 1C Hot rolled, heat treated,1C Hot rolled, heat treated, not descaled not descaled 2,002,00--8,008,00 5050--15501550 6,016,01--8,008,00 750750--155015501D1D Hot rolled, heat treated, pickledHot rolled, heat treated, pickled 1,501,50--8,008,00 5050--15501550 1,501,50--8,008,00 400400--155015501G1G 1G Ground1G Ground 2,002,00--3,003,00 750750--14551455 2,002,00--3,003,00 750750--145514551M1M 1M Patterned1M Patterned 2,002,00--3,003,00 750750--14551455 2,002,00--3,003,00 750750--145514551U1U 1U black hot rolled1U black hot rolled 2,002,00--8,008,00 5050--15501550 6,016,01--8,008,00 750750--15501550C Mn Cr Ni Mo N OtherTypical 0.045 16.5 1.0ASMEASME II A SA II A SA--240240 =0.120.12 =1.001.00 16.016.0--18.018.0 0.750.75--1.251.25ASTM A240ASTM A240 =0.120.12 =1.001.00 16.016.0--18.018.0 0.750.75--1.251.25EN 10088EN 10088--22 =0.080.08 =1.01.0 16.016.0--18.018.0 0.90.9--1.41.4Pitting corrosion resistance Crevice corrosion resistancePRE CPT CCT2020 <10<10 <0<02 - Outokumpu 4113 Printed: 23 jun 2015For a more detailed description of their corrosion resistance properties in different environments see Outokumpu Corrosion Handbook.For a more detailed description of their corrosion resistance properties in different environments see Outokumpu Corrosion Handbook. 3 - Outokumpu 4113 Printed: 23 jun 2015    Mechanical properties 1)1)Elongation according to EN standard:Elongation according to EN standard: AA8080 for thickness below 3 mm. for thickness below 3 mm. A for thickness = 3 mm.A for thickness = 3 mm. Elongation accordingElongation according to ASTM standard A to ASTM standard A22”” or Aor A5050. . Physical properties Fabrication More detailed information concerning welding procedures can be obtained from the Outokumpu Welding Handbook, available from our More detailed information concerning welding procedures can be obtained from the Outokumpu Welding Handbook, available from our sales offices.sales offices. Standards & approvals     Cold rolled coil and sheetRp0.2 MPaRp1.0 MPaRm MPaElongation1) %Impact strength J Rockwell HB HVTypical (Thickness 1mm) 390 420 550ASMEASME II A SA II A SA--240240 = 240 240 = 450 450ASTM A240ASTM A240 = 240 240 = 450 450  Hot rolled coil and sheetRp0.2 MPaRp1.0 MPaRm MPaElongation1) %Impact strength J Rockwell HB HVASMEASME II A SA II A SA--240240 = 240 240 = 450 450ASTM A240ASTM A240 = 240 240 = 450 450  Hot rolled quarto plateRp0.2 MPaRp1.0 MPaRm MPaElongation1) %Impact strength J Rockwell HB HVASMEASME II A SA II A SA--240240 = 240 240 = 450 450ASTM A240ASTM A240 = 240 240 = 450 450DensityModulus of elasticityThermal exp. at 100°CThermal conductivityThermal capacityElectrical resistance Magnetizablekg/dm3 GPa 10-6/°C W/m°C J/kg°C µOm7,77,7 220220 10,010,0 2525 460460 0,700,70 YesYesStandard DesignationASME SAASME SA--240M Code Sect. II. Part A240M Code Sect. II. Part A 434 / UNS S43400434 / UNS S43400ASTM A240/A240MASTM A240/A240M 434 / UNS S43400434 / UNS S43400EN 10088EN 10088--22 1.41131.41134 - Outokumpu 4113 Printed: 23 jun 2015   Contacts & Enquiries Contact your nearest sales office www.outokumpu.com/contactswww.outokumpu.com/contacts    5 - Outokumpu 4113 Printed: 23 jun 2015Working towards forever. We work with our customers and We work with our customers and partnerspartners to create long lasting solutions to create long lasting solutions for the toolsfor the tools of modern life and the of modern life and the worldworld’’s most critical problems:s most critical problems: Clean Clean energy, clean water and efficient energy, clean water and efficient infrastructure. Because we believe in a infrastructure. Because we believe in a world that lasts forever.world that lasts forever. Information given in this brochure may be subject to alterations without notice. Care has been taken to ensure that the contents of this Information given in this brochure may be subject to alterations without notice. Care has been taken to ensure that the contents of this publication are accurate but Outokumpu and its affiliated companies do not accept responsibility for errors or for information which is publication are accurate but Outokumpu and its affiliated companies do not accept responsibility for errors or for information which is found to be misleading. Suggestions for or descriptions of the end use or application of products or methods of working are for information found to be misleading. Suggestions for or descriptions of the end use or application of products or methods of working are for information only and Outokumpu and its affiliated companies accept no liability in respect thereof. Before using products supplied or manufactured by only and Outokumpu and its affiliated companies accept no liability in respect thereof. Before using products supplied or manufactured by the company the customer should satisfy himself of their suitabilitythe company the customer should satisfy himself of their suitabilityoutokumpu.com steelfinder.outokumpu.com6 - Outokumpu 4113 Printed: 23 jun 20157 - Outokumpu 4113 Printed: 23 jun 2015