Absorbents-Oil & Universal - Sonic Bonded Pads Brochure

MATERIAL SAFETY DATA SHEET SECTION I: IDENTIFICATION OF PRODUCT PRODUCT NAME: Gray Universal Sonic Bonded Sorbents CHEMICAL FAMILY: Olefin MANUFACTURER’S NAME: SpillTech Manufacturing Location: SpillTech Brookley Industrial Complex 1627 O’Donoghue Street Mobile, AL 36615 Customer Service Telephone Number: 1-800-228-3877 Technical Information Telephone Number: 1-251-694-0102 ext.121 Date Prepared: April 29, 2002 SECTION II: HAZARDOUS INGREDIENTS INGREDIENTS PERCENT CAS NUMBER OSHA PEL ACGIH TLVPolypropylene 98.3% 9003-07-0 N/A N/A Surfactant 1.4% N/A N/A N/A Gray Pigment 0.3% N/A N/A N/A (Carbon Black) 23.5% 1333-86-4 3.5mg/m3 3.5mg/m3 (Polypropylene) 76.5% 9003-07-0 N/A N/A Note: Sub-ingredients of main ingredient are in parentheses SECTION III: HAZARDS IDENTIFICATION NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) RATING: HEALTH: 0 FLAMMABILITY: 1 REACTIVITY: 0 *Not considered a hazardous material at temperatures below melting point. Not considered a controlled substance or a carcinogen. Page 2 of 3 - Gray Universal Sonic Bonded Sorbents SECTION IV: FIRST AID MEASURES EYE CONTACT: Use eyewash, consult physician if accompanied by pain or irritation. SKIN CONTACT: N/A INHALATION: N/A INGESTION: N/A SECTION V: FIRE FIGHTING MEASURES FLASH POINT: 329o C (625o F) AUTO IGNITION: 357o C (675o F) FLAMMABLE LIMITS: N/A FIRE EXTINGUISHING MEDIA: Water, Foam, CO2, Dry Chemical SPECIAL FIRE FIGHTING PROCEDURES: Standard procedures for Class A fires UNUSUAL FIRE AND EXPLOSION HAZARDS: Some carbon monoxide formation is possible under oxygen-lean conditions. Matting will not support combustion. Sorbents will take on the characteristics/properties of whatever liquid is absorbed. Therefore, all measures must be taken as if you were handling the liquid itself. Sorbents do not make the liquid less hazardous. Always refer to the MSDS for the chemical absorbed before proceeding SECTION VI: ACCIDENTAL RELEASE MEASURES No special steps to be taken if material is spilled or released. SECTION VII: HANDLING AND STORAGE Store in dry area. Do not store near open flame, high heat, strong oxidants, or halogenated hydrocarbons. Polypropylene, when heated, becomes very sticky and will burn. Use self-contained air masks to enter smoky area in the event of fire. Adequate ventilation is required to remove decomposition products when temperature exceeds melting point. Avoid contact with melted product. Sorbents will take on the characteristics/properties of whatever liquid is absorbed. Therefore, all measures must be taken as if you were handling the liquid itself. Sorbents do not make the liquid less hazardous. Always refer to the MSDS for the chemical absorbed before proceeding SECTION VIII: EXPOSURE CONTROLS/ PERSONAL PROTECTION EQUIPMENT RESPIRATORY PROTECTION: None Required VENTILATION: None Required PROTECTIVE GLOVES: None Required EYE PROTECTION: Safety glasses with side shields are recommended as a good practice for industrial safety. OTHER PROTECTIVE EQUIPMENT (SPECIFY): None Required Page 3 of 3 - Gray Universal Sonic Bonded Sorbents SECTION IX: PHYSICAL DATA APPEARANCE AND ODOR: Gray & virtually odor free SPECIFIC GRAVITY: 0.88 – 0.92 BOILING POINT (C): Not Applicable MELTING POINT (C): >160o C (320o F) SOLUBILITY IN WATER: Insoluble PERCENT VOLATILE BY VOLUME: N/A EVAPORATION RATE: N/A VAPOR PRESSURE (mm Hg): N/A VAPOR DENSITY (Air = 1): N/A SECTION X: TRANSPORT INFORMATION DOT CLASSIFICATION: Non Hazardous SECTION XI: WASTE XI DISPOSAL METHOD Disposal must be done in accordance with local, state and federal regulations based on chemicals adsorbed by products. Sorbents will take on the characteristics/properties of whatever liquid is absorbed. Therefore, all measures must be taken as if you were handling the liquid itself. Sorbents do not make the liquid less hazardous. Always refer to the MSDS for the chemical absorbed before proceeding SECTION XII: PREPARATION The information contained herein is given in good faith, but no warranty, expressed or implied, is made. DATE ISSUED: April 29, 2002 UPDATED: February 2005 PREPARED BY: SpillTech, Telephone Number: 1-800-228-3877. SECTION II: HAZARDOUS INGREDIENTS SECTION III: HAZARDS IDENTIFICATION Page 2 of 3 - Gray Universal Sonic Bonded Sorbents SECTION IX: PHYSICAL DATA SECTION X: TRANSPORT INFORMATION DOT CLASSIFICATION: Non Hazardous