Advantage II Pellets

Advantage II Material Safety Data Sheet Date Prepared: August 1, 2013 Supersedes Date: April 11, 2013 1. PRODUCT AND COMPANY IDENTIFICATION AQUATROLS CORPORATION OF AMERICA 1273 IMPERIAL WAY PAULSBORO, NJ 08066 USA Emergency Phone Numbers: For emergencies involving a spill, leak, fire, exposure or accident, contact CHEMTREC (800-424-9300 within the United States or 1-703-527-3887 for international collect calls). For Product Information: 1-800-257-7797 / 1-856-537-6003 Chemical Name or Synonym: Not available For research and development use only: To be used by, or under the direct supervision of a technically qualified individual. Treat product accordingly. 2. HAZARDS IDENTIFICATION Emergency Overview: CAUTION – May cause eye irritation Potential Health Effects Acute Ingestion: May cause irritation Acute Skin: Prolonged or repeated skin contact may result in slight, temporary irritation Acute Inhalation: Inhalation of vapors or mists may result in respiratory irritation Acute Eyes: Contact with eyes may result in temporary irritation Primary Routes of Entry: Routes of entry for liquids and solids include eye and skin contact, ingestion and inhalation Chronic Effects: There are no known chronic effects associated with this material 3. COMPOSITION / INFORMATION ON INGREDIENTS Product Composition CAS Reg No. WGT. % A. Hazardous None B. Non-Hazardous Polyoxypropylene – Polyoxyethylene – block polymer Proprietary 40.28 Polyalkylene glycol ether Proprietary 40.28 Water soluble binder Proprietary 14.44 4. FIRST AID MEASURES Eye: DO NOT RUB EYES. Immediately flush with large amounts of water for 15 mins lifting the lower and upper lids. Seek medical attention if necessary. Skin: Remove contaminated clothing and immediately wash affected area with large amounts of water for at least 5 minutes. If irritant or redness persists, seek medical attention as needed. Ingestion: Give large amounts of water to drink. Seek medical attention if necessary. Induce vomiting only upon advice from a physician. Never give anything by mount if victim is unconscious or having convulsions. Inhalation: Move individual to fresh air and check to assure adequate respiration. Seek medical attention if necessary. Notes to Physician: All treatments should be based on observed signs and symptoms of distress in the patient. Consideration should be given to the possibility that overexposure to materials other than this product may have occurred. Treat symptomatically. No specific antidote is available. 5. FIRE FIGHTING MEASURES Flashpoint and Method: Not established Unusual Fire and Explosion Hazards: There are no known unusual fire or explosion hazards Extinguishing Media: Use water fog, foam dry chemical, or carbon dioxide extinguishing media Special Fire Fighting Procedures: Firefighters should be equipped with self-contained breathing • Page 1 of 4 Advantage II Material Safety Data Sheet Date Prepared: August 1, 2013 Supersedes Date: April 11, 2013 apparatus and turn out gear. Hazardous Decomposition Materials (Under Fire Conditions): None known 6. ACCIDENTAL RELEASE MEASURES Cleanup and Disposal of Spill: If material is in pellet form, shovel or otherwise collect into recovery drums. If material is in liquid form, control the spill with dykes and absorb with absorbent pads or booms. If necessary, apply granular or loose sorbent to spill. When adsorbed, sweep or otherwise collect into recovery drums and dispose of properly. A comprehensive spill response plan should be developed and implemented. See Waste Disposal information in Section 13. Environmental and Regulatory Reporting: This material is not regulated by RCRA or CERCLA (“Superfund”). Containment of spill: Spills should be contained, solidified and placed in suitable containers for disposal in a licensed facility 7. HANDLING AND STORAGE Handling: Avoid inhalation of vapor or mist. Avoid contact with eyes and skin. Use only with adequate ventilation. Practice proper personal hygiene. Storage: Keep containers closed. Store in a cool, dry, well-ventilated area, away from incompatible substances 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Introductory Remarks: These recommendations provide general guidance for handling this product. Because specific work environments and material handling practices vary, safety procedures should be developed for each intended application. While developing safe handling procedures, do not overlook the need to clean equipment and piping systems for maintenance and repairs. Waste resulting from these procedures should be handled in accordance with Section 13: Disposal Considerations. Exposure Guidelines: No exposure limits were found for this product or any of its ingredients. Engineering Controls: Use adequate general or local exhaust ventilation to keep airborne concentrations to a minimum Skin: Skin contact should be minimized through use of appropriate clothing and suitable long-sleeved clothing (i.e., shirts and pants). Consideration must be given both to durability as well as permeation resistance. USDA accepted NITRILE (CFR-20) or neoprene rubber (CFR-21) gloves are recommended Respiratory: Use approved organic vapor mist respirator as necessary. Eye / Face Protection: Wear appropriate protective safety goggles/glasses as described in 29 CFR 1910.133 or full-face shield if splashing hazard exists. Work Practice Controls: Personal hygiene is an important work practice exposure control measure and the following general measures should be taken when working with or handling this material. 1. Do not store, use, and/or consume food, beverages, tobacco products, or cosmetics in area where this material is stored. 2. Wash hands and face carefully before eating, drinking, using tobacco, applying cosmetics, or using the toilet 3. Wash exposed skin promptly to remove accidental splashes of contact with this material. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical State: White solid Odor: Mild aromatic, slight ammonia odor Color: White pH: Not determined • Page 2 of 4 Advantage II Material Safety Data Sheet Date Prepared: August 1, 2013 Supersedes Date: April 11, 2013 Vapor Pressure: Not determined Vapor Density: 1.004g/ml Boiling Point: Not determined Freezing Point: Not determined Melting Point: Not determined Flashpoint and Method: Not determined Solubility in Water: Soluble Evaporation Rate: Not determined Vapor Density (air =1): >1 Specific Gravity: Not determined Viscosity #1: Not determined Molecular Weight: Not determined Coeff. Oil/Water: Not determined 10. STABILITY AND REACTIVITY Chemical Stability: This material is stable under normal handling and storage conditions described in Section 7. Hazardous Polymerization: Will not occur Conditions to Avoid: Keep away from heat and flames Hazardous Decomposition Products: Oxides of carbon and hydrogen Incompatible Materials: Strong oxidizing agents 11. TOXICOLOGICAL INFORMATION Acute Eyes: No data available Dermal LD: No data available Oral LD: No data available Inhalation LC: No data available Eye Effects: No data available Skin Effects: No data available 12. ECOLOGICAL INFORMATION Environmental Data: No data available Ecotoxicological Information: No data available Distribution: No data available Chemical/Physical Information: Not corrosive, not an oxidizer 13. DISPOSAL CONSIDERATIONS Waste Disposal Method: Not determined Empty Container: Dispose of wastes in a manner consistent with federal, state, and local regulation. 14. TRANSPORTATION INFORMATION DOT (Department of Transportation) Proper Shipping Name: Cleaning compound NOI Primary Hazard Class / Division: None UN / NA Number: Not applicable Packing Group: Not applicable NMFC 48580 Class 3 U.S. Customs Harmonization Number: 340213.0000.3 • Page 3 of 4 Advantage II Material Safety Data Sheet Date Prepared: August 1, 2013 Supersedes Date: April 11, 2013 15. REGULATORY INFORMATION United States DOT Label Symbol and Hazard Classification Irritant SARA Title III (Superfund Amendments and Reauthorization Act) Not determined Fire: Pressure Generating: Reactivity: Acute: Chronic: 313 Reportable Ingredients: Not determined Title III Notes: Not determined CERCLA (Comprehensive Response, Compensation, and Liability act) Not determined CERCLA RQ: Not determined TSCA (Toxic Substance Control Act: Not determined TSCA Regulatory: Not determined REGULATIONS: Not determined State Regulations: Not determined Local Regulations: Not determined National Response Center: Not determined CANADA WHMIS (Workplace Hazardous Materials Information System) Symbol and Classification: Not determined Canada Ingredient Disclosure List: Not determined Canadian Environmental Protection Act: Not determined European Community Not determined EEC Label Symbol and Classification Not determined European Community Regulatory: Not determined Mexico Not determined 16. OTHER INFORMATION Reason for Issue: Review with revisions Information Contact: Aquatrols Corporation of America – 1-800-257-7795 / 1-856-537-6003 Revision Summary: Section 3. This MSDS replaces MSDS dated April 11, 2013. HMIS Rating NFPA CODES HEALTH: HEALTH: FLAMMABILITY: FLAMMABILITY: PHYSICAL HAZARD: INSTABILITY: PERSONAL PROTECTION: Manufacturer Disclaimer: The information provided on the SDS is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information related only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text. While we believe the information contained herein is reliable, it is being provided on an “as is” basis, without representation or warranty, express or implied, regarding accuracy, adequacy, completeness, reliability of usefulness for any purpose. Aquatrols shall have no liability to any person relating to or resulting from the use of the information provided herein or any errors or omissions therein. End of MSDS Document • Page 4 of 4