Agru - Model MicroSpike - Liner - Brochure

© Agru America, Inc. 2010500 Garrison Road, Georgetown, South Carolina 29440 843-546-0600 800-373-2478 Fax: 843-527-2738email: salesmkg@agruamerica.com www.agruamerica.comSupply Information (Standard Roll Dimensions)Thickness Width Length Area (approx.) Weight (average)*mil mm ft m ft m ft2 m2 lbs kgThickness, nominal (mm) 30 (.75) 40 (1.0) 60 (1.5) 80 (2.0) 100 (2.5)Thickness (min. ave.), mil (mm) ASTM D5994* 29 (.71) 38 (.95) 57 (1.43) 76 (1.90) 95 (2.38)Thickness (lowest indiv. for 8 of 10 spec.), mil (mm) ASTM D5994* 27 (.68) 36 (.90) 54 (1.35) 72 (1.80) 90 (2.25)Thickness (lowest indiv. for 1 of 10 spec.), mil (mm) ASTM D5994* 26 (.64) 34 (.85) 51 (1.28) 68 (1.70) 85 (2.13)*The thickness values may be changed due to project specifications (i.e., absolute minimum thickness)Asperity Height (min. ave.), mil (mm) GRI GM12/ASTM D7466 16 (.41) 16 (.41) 16 (.41) 16 (.41) 16 (.41)Density, g/cc, minimum ASTM D792, Method B 0.94 0.94 0.94 0.94 0.94Tensile Properties (ave. both directions) ASTM D6693, Type IVStrength @ Yield (min. ave.), lb/in width (N/mm) 2 in/minute 66 (11.6) 88 (15.4) 132 (23.1) 176 (30.8) 220 (38.5)Elongation @ Yield (min. ave.), % (GL=1.3in) 5 specimens in each direction 13 13 13 13 13Strength @ Break (min. ave.), lb/in width (N/mm) 66 (11.6) 88 (15.4) 132 (23.1) 176 (30.8) 220 (38.5)Elongation @ Break (min. ave.), % (GL=2.0in) 350 350 350 350 350Tear Resistance (min. ave.), lbs. (N) ASTM D1004 23 (102) 30 (133) 45 (200) 60 (267) 72 (320)Puncture Resistance (min. ave.), lbs. (N) ASTM D4833 60 (267) 90 (400) 120 (534) 150 (667) 180 (801)Carbon Black Content (range in %) ASTM D4218 2 - 3 2 - 3 2 - 3 2 - 3 2 - 3Carbon Black Dispersion (Category) ASTM D5596 Only near spherical agglomeratesfor 10 views: 9 views in Cat. 1 or 2, and 1 view in Cat. 3Stress Crack Resistance (Single Point NCTL), hours ASTM D5397, Appendix 300 300 300 300 300Oxidative Induction Time, minutes ASTM D3895, 200°C, 1 atm O2 =100 =100 =100 =100 =100Melt Flow Index, g/10 minutes ASTM D1238, 190°C, 2.16kg =1.0 =1.0 =1.0 =1.0 =1.0Oven Aging ASTM D5721 80 80 80 80 80with HP OIT, (% retained after 90 days) ASTM D5885, 150°C, 500psi O2UV Resistance GRI GM11 20hr. Cycle @ 75°C/4 hr. dark condensation @ 60°Cwith HP OIT, (% retained after 1600 hours) ASTM D5885, 150°C, 500psi O2 50 50 50 50 5030 .75 23 7 930 283.117 21,390 1,984 3,900 1,77040 1.0 23 7 710 216.41 16,330 1,514.87 3,900 1,77060 1.5 23 7 505 153.53 11,615 1,078 3,900 1,77080 2.0 23 7 385 117.35 8,855 821 3,900 1,770100 2.5 23 7 310 94.49 7,130 661 3,900 1,770High Density PolyethyleneMicro Spike® LinerProduct DataProperty Test Method ValuesThese product specifications meet or exceed GRI’s GM13Notes:All rolls are supplied with two slings. All rolls are wound on a 6 inch core. Special lengths are available on request. All roll lengths and widths have a tolerance of ±1%*The weight values may change due to project specifications (i.e. absolute minimum thickness or special roll lengths) or shipping requirements (i.e. international containerized shipments).All information, recommendations and suggestions appearing in this literature concerning the use of our products are based upon tests and data believedto be reliable; however, it is the users responsibility to determine the suitability for their own use of the products described herein. Since the actual use by others is beyond our control, no guarantee or warranty of any kind, expressed or implied, is made by Agru/America as to the effects of such use or the results to be obtained, nor does Agru/America assume any liability in connection herewith. Any statement made herein may not be absolutelycomplete since additional information may be necessary or desirable when particular or exceptional conditions or circumstances exist or because of applicable laws or government regulations. Nothing herein is to be construed as permission or as a recommendation to infringe any patent.