ARI-FABA - Supra I - Globe Valves - Brochure

ARI-FABA®-Supra I ARI-FABA®-Supra C Straight through with flanges TA - Luft TÜV-Test-No. 973-10183778 TRB 801 Annex II No. 45 ••Cast steelForged steel Stainless steelFig. 146 Page 2-7ARI-FABA®-Supra I ARI-FABA®-Supra C Straight through with butt weld endsTA - Luft TÜV-Test-No. 973-10183778TRB 801 Annex II No. 45•• Forged steel Fig. 140 Page 8-9ARI-FABA®-Supra I ARI-FABA®-Supra C Straight through with butt weld endsTA - Luft TÜV-Test-No. 973-10183778TRB 801 Annex II No. 45•• Cast steelFig. 140 Page 10-11ARI-FABA®-Supra I ARI-FABA®-Supra C Y-pattern with flangesTA - Luft TÜV-Test-No. 973-10183778TRB 801 Annex II No. 45•• Stainless steelFig. 169 Page 12-13ARI-FABA®-Supra I ARI-FABA®-Supra C Y-pattern with butt weld endsTA - Luft TÜV-Test-No. 973-10183778TRB 801 Annex II No. 45••Cast steel Stainless steel Fig. 166 Page 14-17ARI-FABA®-Supra I ARI-FABA®-Supra C Angle pattern with flangesTA - Luft TÜV-Test-No. 973-10183778TRB 801 Annex II No. 45 •• Cast steelFig. 147 Page 18-19ARI-FABA®-SupraStop valve with bellows sealMaintenance free stop valve with bellows seal - metallic sealingFeatures:Double wall bellows seal as standardBellows seal welded to bonnetBellows seal 10.000 load cyclesIndustrial version: Bellows seal shielded Chemical version: Bellows seal flushedStem back sealYoke gasket, double chambered Plug with marginal seatWelded seatExternal stem threadActuator retrofittingSecondary sealing: gland packing (with bridge)Stem with roll hardened thread ••••••••••••Fig. 146 One-piece stemEdition 01/11 - Data subject to alteration Data sheet 040006 englisch (english)Fig. 146 Two-piece stemFor ANSI versions refer to data sheet „ARI-FABA®-Plus/-Supra ANSI“2 Edition 01/11 - Data subject to alterationARI-FABA®-Supra IFig. 146Stop valve - straight through with flanges and bellows seal - Industrial version (Cast steel) Fig. 146....111 DN15-150one-piece stem Fig. 146....112 DN15-150two-piece stemPartsPos. Description Fig. 34. / 35. 146....111 One-piece stem Fig. 34. / 35. 146....112 Two-piece stem1 Body GP240GH+N, 1.0619+N1.2 Seat G19 9 NbSi, 1.45512 Bonnet =DN150: GP240GH+N, 1.0619+N / =DN200: P250 GH, 1.0460; P235GH-TC1, 1.0345; P265 GH, 1.04253 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440844 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists / The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400L (mm) 130 150 160 180 200 230 290 310 350 400 480 600 730 850 980 1100H1 (One-piece stem) (mm) 225 225 230 230 270 275 300 380 460 500 570 785 940 1025 1210 1270H1 (Two-piece stem) (mm) 240 240 240 240 290 295 335 395 505 550 605 810 940 1025 1180 1245ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520 520 520 640 640ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520 520 520 640 640Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50 70 80 90 100Kvs-value (m3/h) 4,7 6,4 11 15,5 28 42,5 75 105 170 270 405 675 1090 1460 2010 2640Zeta-value -- 3,7 6,2 5,2 7 5,2 5,5 5,1 5,9 5,5 5,3 4,9 5,6 5,2 6,1 5,9 5,9Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension FTF Series 1 acc. to DIN EN 558WeightsFigure-No. DN 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 40034.146 (kg) -- -- -- -- -- -- -- -- -- -- -- 194 296 426 642 89435.146 (kg) 4,7 5,7 7 8,1 11,6 14,2 21,9 32,3 47,6 70,6 95 245 330 458 693 953Figure-No. Nominal pressure Material Nominal diameter34.146....111 PN25 1.0619+N DN200-40035.146....111 PN40 1.0619+N DN15-40034.146....112 PN25 1.0619+N DN200-40035.146....112 PN40 1.0619+N DN15-400Test: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) Bonnet DN200-400one-piece stem Bonnet DN200-400two-piece stem 3Edition 01/11 - Data subject to alterationARI-FABA®-Supra CFig. 146Stop valve - straight through with flanges and bellows seal - Chemical version (Cast steel) Fig. 146....153 DN15-150one-piece stem Fig. 146....154 DN15-150two-piece stemPartsPos. Description Fig. 34. / 35. 146....153 One-piece stem Fig. 34. / 35. 146....154 Two-piece stem1 Body GP240GH+N, 1.0619+N1.2 Seat G19 9 NbSi, 1.45512 Bonnet =DN150: GP240GH+N, 1.0619+N / =DN200: P250 GH, 1.0460; P235GH-TC1, 1.0345; P265 GH, 1.04253 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem * X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400L (mm) 130 150 160 180 200 230 290 310 350 400 480 600 730 850 980 1100H1 (One-piece stem) (mm) 225 225 230 230 270 275 300 380 460 500 570 785 940 1025 1210 1270H1 (Two-piece stem) (mm) 240 240 240 240 290 295 335 395 505 550 605 810 940 1025 1180 1245ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520 520 520 640 640ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520 520 520 640 640Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50 70 80 90 100Kvs-value (m3/h) 4,4 6 10 13,3 25,5 38,5 64 90 135 215 325 580 885 1290 1708 2080Zeta-value -- 4,2 7,1 6,2 9,5 6,3 6,7 7 8,1 8,8 8,4 7,7 7,6 8 7,8 8,3 9,4Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension FTF Series 1 acc. to DIN EN 558WeightsFigure-No. DN 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 40034.146 (kg) -- -- -- -- -- -- -- -- -- -- -- 194 296 426 642 89435.146 (kg) 4,7 5,7 7 8,1 11,6 14,2 21,9 32,3 47,6 70,6 95 245 330 458 693 953Figure-No. Nominal pressure Material Nominal diameter34.146....153 PN25 1.0619+N DN200-40035.146....153 PN40 1.0619+N DN15-40034.146....154 PN25 1.0619+N DN200-40035.146....154 PN40 1.0619+N DN15-400Test: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) Bonnet DN200-400one-piece stem Bonnet DN200-400two-piece stem 4 Edition 01/11 - Data subject to alterationFigure-No. Nominal pressure Material Nominal diameter45.146....111 PN40 1.0460 DN15-5045.146....112 PN40 1.0460 DN15-50DN >50 refer to Fig. 35.146 (1.0619+N)Test: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardSelection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) DN15-32Stop valve - straight through with flanges and bellows seal - Industrial version (Forged steel) Fig. 146....111 DN40-50one-piece stem Fig. 146....112 DN40-50two-piece stemPartsPos. Description Fig. 45. 146....111 One-piece stem Fig. 45. 146....112 Two-piece stem1 Body P250 GH, 1.04601.2 Seat G19 9 NbSi, 1.45512 Bonnet GP240GH+N, 1.0619+N3 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X20Cr13+QT, 1.4021+QT5 Handwheel * St (cataphoretic coating) EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440844 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve. DimensionsDN 15 20 25 32 40 50L (mm) 130 150 160 180 200 230H1 (One-piece stem) (mm) 235 235 245 250 275 275H1 (Two-piece stem) (mm) 250 250 255 260 295 295ØC (One-piece stem) (mm) 125 125 125 125 150 150ØC (Two-piece stem) (mm) 140 140 140 140 160 160Travel (mm) 6 6 8 8 13 13Kvs-value (m3/h) 3,4 6 9,5 12,5 21 31Zeta-value -- 7 7,1 6,9 10,7 9,3 10,4Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension FTF Series 1 acc. to DIN EN 558Weights Figure-No. DN 15 20 25 32 40 5045.146 (kg) 4,4 5,4 6,3 7,8 11 13,5ARI-FABA®-Supra IFig. 1465Edition 01/11 - Data subject to alterationFigure-No. Nominal pressure Material Nominal diameter45.146....153 PN40 1.0460 DN15-5045.146....154 PN40 1.0460 DN15-50DN >50 refer to Fig. 35.146 (1.0619+N)Test: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardSelection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) DN15-32Stop valve - straight through with flanges and bellows seal - Chemical version (Forged steel) Fig. 146....153 DN40-50one-piece stem Fig. 146....154 DN40-50two-piece stemPartsPos. Description Fig. 45. 146....153 One-piece stem Fig. 45. 146....154 Two-piece stem1 Body P250 GH, 1.04601.2 Seat G19 9 NbSi, 1.45512 Bonnet GP240GH+N, 1.0619+N3 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X20Cr13+QT, 1.4021+QT5 Handwheel * St (cataphoretic coating) EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve. DimensionsDN 15 20 25 32 40 50L (mm) 130 150 160 180 200 230H1 (One-piece stem) (mm) 235 235 245 250 275 275H1 (Two-piece stem) (mm) 250 250 255 260 295 295ØC (One-piece stem) (mm) 125 125 125 125 150 150ØC (Two-piece stem) (mm) 140 140 140 140 160 160Travel (mm) 6 6 8 8 13 13Kvs-value (m3/h) 3,3 5,8 9,2 11,5 21,5 32Zeta-value -- 7,4 7,6 7,4 12,7 8,8 9,7Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension FTF Series 1 acc. to DIN EN 558Weights Figure-No. DN 15 20 25 32 40 5045.146 (kg) 4,4 5,4 6,3 7,8 11 13,5ARI-FABA®-Supra CFig. 146Edition 01/11 - Data subject to alteration6ARI-FABA®-Supra IFig. 146Stop valve - straight through with flanges and bellows seal - Industrial version (Stainless steel) Fig. 146....111 DN15-150 one-piece stem Fig. 146....112 DN15-150 two-piece stemPartsPos. Description Fig. 54. / 55. 146....111 One-piece stem Fig. 54. / 55. 146....112 Two-piece stem1 Body GX5CrNiMo19-11-2, 1.44082 Bonnet =DN150: GX5CrNiMo19-11-2, 1.4408 / =DN200: X6CrNiMoTi17-12-2, 1.4571 3 Plug * X6CrNiMoTi17 12 2, 1.4571 / Stellit 64.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud A4-708 Hexagon nut A49 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440844 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200 250L (mm) 130 150 160 180 200 230 290 310 350 400 480 600 730H1 (One-piece stem) (mm) 225 225 230 230 270 275 300 380 460 500 570 780 935H1 (Two-piece stem) (mm) 240 240 240 240 290 295 335 395 505 550 605 805 935ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520 520Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50 70Kvs-value (m3/h) 4,7 6,4 11 15,5 28 42,5 75 105 170 270 405 675 1090Zeta-value -- 3,7 6,2 5,2 7 5,2 5,5 5,1 5,9 5,5 5,3 4,9 5,6 5,2Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension FTF Series 1 acc. to DIN EN 558WeightsFigure-No. DN 15 20 25 32 40 50 65 80 100 125 150 200 25054.146 (kg) -- -- -- -- -- -- -- -- -- -- -- 213 30055.146 (kg) 4,9 5,4 7,1 8,1 11,3 14,1 21,8 30 45,5 63,5 78 245 347Figure-No. Nominal pressure Material Nominal diameter54.146....111 PN25 1.4408 DN200-25055.146....111 PN40 1.4408 DN15-25054.146....112 PN25 1.4408 DN200-25055.146....112 PN40 1.4408 DN15-250Test: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Recycling facilities, Chemical industry, Processing technology, Process water installations, Installations with aggressive media, etc.(other applications on request) Selection of possible flow media Aggressive media, etc.(other flow media on request) Bonnet DN200-400one-piece stem Bonnet DN200-400two-piece stem 7Edition 01/11 - Data subject to alterationARI-FABA®-Supra CFig. 146Stop valve - straight through with flanges and bellows seal - Chemical version (Stainless steel) Fig. 146....153 DN15-150one-piece stem Fig. 146....154 DN15-150two-piece stemPartsPos. Description Fig. 54. / 55. 146....153 One-piece stem Fig. 54. / 55. 146....154 Two-piece stem1 Body GX5CrNiMo19-11-2, 1.44082 Bonnet =DN150: GX5CrNiMo19-11-2, 1.4408 / =DN200: X6CrNiMoTi17-12-2, 1.45713 Plug * X6CrNiMoTi17 12 2, 1.4571 / Stellit 64.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud A4-708 Hexagon nut A49 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200 250L (mm) 130 150 160 180 200 230 290 310 350 400 480 600 730H1 (One-piece stem) (mm) 225 225 230 230 270 275 300 380 460 500 570 780 935H1 (Two-piece stem) (mm) 240 240 240 240 290 295 335 395 505 550 605 805 935ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520 520Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50 70Kvs-value (m3/h) 4,4 6 10 13,3 25,5 38,5 64 90 135 215 325 580 885Zeta-value -- 4,2 7,1 6,2 9,5 6,3 6,7 7 8,1 8,8 8,4 7,7 7,6 8Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension FTF Series 1 acc. to DIN EN 558WeightsFigure-No. DN 15 20 25 32 40 50 65 80 100 125 150 200 25054.146 (kg) -- -- -- -- -- -- -- -- -- -- -- 213 30055.146 (kg) 4,9 5,4 7,1 8,1 11,3 14,1 21,8 30 45,5 63,5 78 245 347Figure-No. Nominal pressure Material Nominal diameter54.146....153 PN25 1.4408 DN200-25055.146....153 PN40 1.4408 DN15-25054.146....154 PN25 1.4408 DN200-25055.146....154 PN40 1.4408 DN15-250Test: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Recycling facilities, Chemical industry, Process pipes, Processing technology, Process water installations, Installations with aggressive media, etc.(other applications on request) Selection of possible flow media Aggressive media, Chemical products, etc.(other flow media on request) Bonnet DN200-250one-piece stem Bonnet DN200-250two-piece stem 8Stop valve - straight through with butt weld ends and bellows seal - Industrial version (Forged steel) Fig. 140....111 one-piece stem Fig. 140....112 two-piece stemFigure-No. Nominal pressure Material Nominal diameter45.140....111 PN40 1.0460 DN15-5045.140....112 PN40 1.0460 DN15-50DN >50 refer to Fig. 35.140 (1.0619+N)Butt weld ends according to DIN EN 12627 - 4 (refer to page 20)Test: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardSelection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) PartsPos. Description Fig. 45. 140....111 One-piece stem Fig. 45. 140....112 Two-piece stem1 Body P250 GH, 1.04601.2 Seat G19 9 NbSi, 1.45512 Bonnet GP240GH+N, 1.0619+N3 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X20Cr13+QT, 1.4021+QT5 Handwheel * St (cataphoretic coating) EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440844 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50L (mm) 130 150 160 180 200 230H1 (One-piece stem) (mm) 235 235 245 250 295 300H1 (Two-piece stem) (mm) 250 250 255 260 315 320ØC (One-piece stem) (mm) 125 125 125 125 150 150ØC (Two-piece stem) (mm) 140 140 140 140 160 160Travel (mm) 6 6 8 8 13 13Kvs-value (m3/h) 3,4 6 9,5 12,5 18,5 28Zeta-value -- 7 7,1 6,9 10,7 11,9 12,7Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Face-to-face dimension ETE series 1 according to DIN EN 12982Weights Figure-No. DN 15 20 25 32 40 5045.140 (kg) 3,2 3,4 4,6 5 6,8 9,7ARI-FABA®-Supra IFig. 140Edition 01/11 - Data subject to alteration9Stop valve - straight through with butt weld ends and bellows seal - Chemical version (Forged steel) Fig. 140....153 one-piece stem Fig. 140....154 two-piece stemFigure-No. Nominal pressure Material Nominal diameter45.140....153 PN40 1.0460 DN15-5045.140....154 PN40 1.0460 DN15-50DN >50 refer to Fig. 35.140 (1.0619+N)Butt weld ends according to DIN EN 12627 - 4 (refer to page 20)Test: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardSelection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) PartsPos. Description Fig. 45. 140....153 One-piece stem Fig. 45. 140....154 Two-piece stem1 Body P250 GH, 1.04601.2 Seat G19 9 NbSi, 1.45512 Bonnet GP240GH+N, 1.0619+N3 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X20Cr13+QT, 1.4021+QT5 Handwheel * St (cataphoretic coating) EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50L (mm) 130 150 160 180 200 230H1 (One-piece stem) (mm) 235 235 245 250 295 300H1 (Two-piece stem) (mm) 250 250 255 260 315 320ØC (One-piece stem) (mm) 125 125 125 125 150 150ØC (Two-piece stem) (mm) 140 140 140 140 160 160Travel (mm) 6 6 8 8 13 13Kvs-value (m3/h) 3,3 5,8 9,2 11,5 19 29Zeta-value -- 7,4 7,6 7,4 12,7 11,3 11,9Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Face-to-face dimension ETE series 1 according to DIN EN 12982Weights Figure-No. DN 15 20 25 32 40 5045.140 (kg) 3,2 3,4 4,6 5 6,8 9,7ARI-FABA®-Supra CFig. 140Edition 01/11 - Data subject to alteration10Stop valve - straight through with butt weld ends and bellows seal - Industrial version (Cast steel) Fig. 140....111 DN65-150one-piece stem Fig. 140....112 DN65-150two-piece stemFigure-No. Nominal pressure Material Nominal diameter35.140....111 PN40 1.0619+N DN65-30035.140....112 PN40 1.0619+N DN65-300Butt weld ends according to DIN EN 12627 - 4 (refer to page 20) alternative: DN 65-200 with shoed ends of P235GHTest: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) alternativ Bonnet DN200-300one-piece stem Bonnet DN200-300two-piece stem PartsPos. Description Fig. 35.140....111 One-piece stem Fig. 35.140....112 Two-piece stem1 Body GP240GH+N, 1.0619+N1.2 Seat G19 9 NbSi, 1.45512 Bonnet =DN150: GP240GH+N, 1.0619+N / =DN200: P250 GH, 1.0460; P235GH-TC1, 1.0345; P265 GH, 1.04253 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X20Cr13+QT, 1.4021+QT5 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440837 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 65 80 100 125 150 200 250 300L (mm) 290 310 350 400 480 600 730 850H1 (One-piece stem) (mm) 300 380 460 500 570 785 940 1025H1 (Two-piece stem) (mm) 335 390 505 550 605 810 940 1025ØC (One-piece stem) (mm) 175 225 300 300 400 520 520 520ØC (Two-piece stem) (mm) 180 225 300 300 400 520 520 520Travel (mm) 16 20 25 32 40 50 70 80Kvs-value (m3/h) 75 105 170 270 405 675 1090 1460Zeta-value -- 5,1 5,9 5,5 5,3 4,9 5,6 5,2 6,1Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Face-to-face dimension ETE series 1 according to DIN EN 12982Weights Figure-No. DN 65 80 100 125 150 200 250 30035.140 (kg) 14,8 22 36,2 50 63 186 270 409ARI-FABA®-Supra IFig. 140Edition 01/11 - Data subject to alteration11Edition 01/11 - Data subject to alterationStop valve - straight through with butt weld ends and bellows seal - Chemical version (Cast steel) Fig. 140....153 DN65-150one-piece stem Fig. 140....154 DN65-150two-piece stemFigure-No. Nominal pressure Material Nominal diameter35.140....153 PN40 1.0619+N DN65-30035.140....154 PN40 1.0619+N DN65-300Butt weld ends according to DIN EN 12627 - 4 (refer to page 20) alternative: DN 65-200 with shoed ends of P235GHTest: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) alternativ Bonnet DN200-300one-piece stem Bonnet DN200-300two-piece stem PartsPos. Description Fig. 35.140....153 One-piece stem Fig. 35.140....154 Two-piece stem1 Body GP240GH+N, 1.0619+N1.2 Seat G19 9 NbSi, 1.45512 Bonnet =DN150: GP240GH+N, 1.0619+N / =DN200: P250 GH, 1.0460; P235GH-TC1, 1.0345; P265 GH, 1.04253 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X20Cr13+QT, 1.4021+QT5 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 65 80 100 125 150 200 250 300L (mm) 290 310 350 400 480 600 730 850H1 (One-piece stem) (mm) 300 380 460 500 570 785 940 1025H1 (Two-piece stem) (mm) 335 390 505 550 605 810 940 1025ØC (One-piece stem) (mm) 175 225 300 300 400 520 520 520ØC (Two-piece stem) (mm) 180 225 300 300 400 520 520 520Travel (mm) 16 20 25 32 40 50 70 80Kvs-value (m3/h) 64 90 135 215 325 580 885 1290Zeta-value -- 7 8,1 8,8 8,4 7,7 7,6 8 7,8Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Face-to-face dimension ETE series 1 according to DIN EN 12982Weights Figure-No. DN 65 80 100 125 150 200 250 30035.140 (kg) 14,8 22 36,2 50 63 186 270 409ARI-FABA®-Supra CFig. 14012ARI-FABA®-Supra IFig. 169Stop valve - Y-pattern with flanges and bellows seal - Industrial version (Stainless steel) Fig. 169....111 DN15-150one-piece stem Fig. 169....112 DN15-150two-piece stemPartsPos. Description Fig. 54. / 55.169....111 One-piece stem Fig. 54. / 55.169....112 Two-piece stem1 Body GX5CrNiMo19-11-2, 1.44082 Bonnet =DN150: GX5CrNiMo19-11-2, 1.4408 / =DN200: X6CrNiMoTi17-12-2, 1.4571 3 Plug * X6CrNiMoTi17 12 2, 1.4571 / Stellit 64.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud A4-708 Hexagon nut A49 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440844 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists / The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200L (mm) 130 150 160 180 200 230 290 310 350 400 480 600H2 (One-piece stem) (mm) 210 210 220 220 270 270 310 385 455 500 590 795H2 (Two-piece stem) (mm) 225 225 230 230 285 285 365 400 490 535 615 840ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520B (One-piece stem) (mm) 110 85 85 70 95 65 50 125 185 170 180 255B (Two-piece stem) (mm) 120 95 90 75 110 80 75 135 210 200 205 590Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50Kvs-value (m3/h) 6 9 14 19 32,5 48 83 119 190 300 450 745Zeta-value -- 2,2 3,2 3,2 4,6 3,9 4,3 4,1 4,6 4,4 4,3 4 4,6Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension FTF Series 1 acc. to DIN EN 558WeightsFigure-No. DN 15 20 25 32 40 50 65 80 100 125 150 20052. / 54.169 (kg) 4,6 5,1 6,2 7,3 9,5 13,2 18,8 26,8 43,7 53,8 69 206Figure-No. Nominal pressure Material Nominal diameter54.169....111 PN25 1.4408 DN15-20055.169....111 PN40 1.4408 DN15-15054.169....112 PN25 1.4408 DN15-20055.169....112 PN40 1.4408 DN15-150Test: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Recycling facilities, Chemical industry, Processing technology, Process water installations, Installations with aggressive media, etc.(other applications on request) Selection of possible flow media Aggressive media, etc.(other flow media on request) Bonnet DN200one-piece stem Bonnet DN200two-piece stem Edition 01/11 - Data subject to alteration13Edition 01/11 - Data subject to alterationARI-FABA®-Supra CFig. 169Stop valve - Y-pattern with flanges and bellows seal - Chemical version (Stainless steel) Fig. 169....153 DN15-150one-piece stem Fig. 169....154 DN15-150two-piece stemPartsPos. Description Fig. 54. / 55.169....153 One-piece stem Fig. 54. / 55.169....154 Two-piece stem1 Body GX5CrNiMo19-11-2, 1.44082 Bonnet =DN150: GX5CrNiMo19-11-2, 1.4408 / =DN200: X6CrNiMoTi17-12-2, 1.4571 3 Plug * X6CrNiMoTi17 12 2, 1.4571 / Stellit 64.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud A4-708 Hexagon nut A49 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200L (mm) 130 150 160 180 200 230 290 310 350 400 480 600H2 (One-piece stem) (mm) 210 210 220 220 270 270 310 385 455 500 590 795H2 (Two-piece stem) (mm) 225 225 230 230 285 285 365 400 490 535 615 840ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520B (One-piece stem) (mm) 110 85 85 70 95 65 50 125 185 170 180 255B (Two-piece stem) (mm) 120 95 90 75 110 80 75 135 210 200 205 590Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50Kvs-value (m3/h) 5,5 8 12,5 17 28 42 72 100 150 239 360 595Zeta-value -- 2,7 4 4 5,8 5,2 5,7 5,5 6,5 7,1 6,8 6,2 7,2Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension FTF Series 1 acc. to DIN EN 558WeightsFigure-No. DN 15 20 25 32 40 50 65 80 100 125 150 20052. / 54.169 (kg) 4,6 5,1 6,2 7,3 9,5 13,2 18,8 26,8 43,7 53,8 69 206Figure-No. Nominal pressure Material Nominal diameter54.169....153 PN25 1.4408 DN15-20055.169....153 PN40 1.4408 DN15-15054.169....154 PN25 1.4408 DN15-20055.169....154 PN40 1.4408 DN15-150Test: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Recycling facilities, Chemical industry, Process pipes, Processing technology, Process water installations, Installations with aggressive media, etc.(other applications on request) Selection of possible flow media Aggressive media, Chemical products, etc.(other flow media on request) Bonnet DN200one-piece stem Bonnet DN200two-piece stem Edition 01/11 - Data subject to alteration14Stop valve - Y-pattern with butt weld ends and bellows seal - Industrial version (Cast steel) Fig. 166....111 DN15-150one-piece stem Fig. 166....112 DN15-150two-piece stemPartsPos. Description Fig. 35.166....111 One-piece stem Fig. 35.166....112 Two-piece stem1 Body GP240GH+N, 1.0619+N1.2 Seat G19 9 NbSi, 1.45512 Bonnet =DN150: GP240GH+N, 1.0619+N / =DN200: P250 GH, 1.0460; P235GH-TC1, 1.0345; P265 GH, 1.04253 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440837 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists / The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200 250 300L (mm) 130 150 160 180 200 230 290 310 350 400 480 600 730 850H2 (One-piece stem) (mm) 210 210 220 220 270 270 310 385 455 500 590 795 905 990H2 (Two-piece stem) (mm) 225 225 230 230 285 285 365 400 490 535 615 840 950 1035ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520 520 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520 520 520B (One-piece stem) (mm) 110 85 85 70 95 65 50 125 185 170 180 255 235 205B (Two-piece stem) (mm) 120 95 90 75 110 80 75 135 210 200 205 290 270 240Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50 70 80Kvs-value (m3/h) 6 9 14 19 32,5 48 83 119 190 300 450 745 1200 1610Zeta-value -- 2,2 3,2 3,2 4,6 3,9 4,3 4,1 4,6 4,4 4,3 4 4,6 4,3 5Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Face-to-face dimension ETE series 1 according to DIN EN 12982Weights Figure-No. DN 15 20 25 32 40 50 65 80 100 125 150 200 250 30035.166 (kg) 3,4 3,6 4,2 4,4 5,5 8,8 11,8 16,5 42,5 52,5 69 164 257 349Figure-No. Nominal pressure Material Nominal diameter35.166....111 PN40 1.0619+N DN15-30035.166....112 PN40 1.0619+N DN15-300Butt weld ends according to DIN EN 12627 - 4 (refer to page 20)Test: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) Bonnet DN200-300one-piece stem Bonnet DN200-300two-piece stem ARI-FABA®-Supra IFig. 16615Edition 01/11 - Data subject to alterationStop valve - Y-pattern with butt weld ends and bellows seal - Chemical version (Cast steel) Fig. 166....153 DN15-150one-piece stem Fig. 166....154 DN15-150two-piece stemPartsPos. Description Fig. 35.166....153 One-piece stem Fig. 35.166....154 Two-piece stem1 Body GP240GH+N, 1.0619+N1.2 Seat G19 9 NbSi, 1.45512 Bonnet =DN150: GP240GH+N, 1.0619+N / =DN200: P250 GH, 1.0460; P235GH-TC1, 1.0345; P265 GH, 1.04253 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200 250 300L (mm) 130 150 160 180 200 230 290 310 350 400 480 600 730 850H2 (One-piece stem) (mm) 210 210 220 220 270 270 310 385 455 500 590 795 905 990H2 (Two-piece stem) (mm) 225 225 230 230 285 285 365 400 490 535 615 840 950 1035ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520 520 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520 520 520B (One-piece stem) (mm) 110 85 85 70 95 65 50 125 185 170 180 255 235 205B (Two-piece stem) (mm) 120 95 90 75 110 80 75 135 210 200 205 290 270 240Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50 70 80Kvs-value (m3/h) 5,5 8 12,5 17 28 42 72 100 150 239 360 595 960 1280Zeta-value -- 2,7 4 4 5,8 5,2 5,7 5,5 6,5 7,1 6,8 6,2 7,2 6,8 7,9Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Face-to-face dimension ETE series 1 according to DIN EN 12982Weights Figure-No. DN 15 20 25 32 40 50 65 80 100 125 150 200 250 30035.166 (kg) 3,4 3,6 4,2 4,4 5,5 8,8 11,8 16,5 42,5 52,5 69 in preparationFigure-No. Nominal pressure Material Nominal diameter35.166....153 PN40 1.0619+N DN15-30035.166....154 PN40 1.0619+N DN15-300Butt weld ends according to DIN EN 12627 - 4 (refer to page 20)Test: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) Bonnet DN200-300one-piece stem Bonnet DN200-300two-piece stem ARI-FABA®-Supra CFig. 166Edition 01/11 - Data subject to alteration16Stop valve - Y-pattern with butt weld ends and bellows seal - Industrial version (Stainless steel) Fig. 166....111 DN15-150one-piece stem Fig. 166....112 DN15-150two-piece stemPartsPos. Description Fig. 55.166....111 One-piece stem Fig. 55.166....112 Two-piece stem1 Body GX5CrNiMoN19-11-2, 1.45812 Bonnet =DN150: GX5CrNiMo19-11-2, 1.4408 / =DN200: X6CrNiMoTi17-12-2, 1.4571 3 Plug * X6CrNiMoTi17 12 2, 1.4571 / Stellit 64.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud A4-708 Hexagon nut A49 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440844 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200L (mm) 130 150 160 180 200 230 290 310 350 400 480 600H2 (One-piece stem) (mm) 210 210 220 220 270 270 310 385 455 500 590 795H2 (Two-piece stem) (mm) 225 225 230 230 285 285 365 400 490 535 615 840ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520B (One-piece stem) (mm) 110 85 85 70 95 65 50 125 185 170 180 255B (Two-piece stem) (mm) 120 95 90 75 110 80 75 135 210 200 205 290Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50Kvs-value (m3/h) 6 9 14 19 32,5 48 83 119 190 300 450 745Zeta-value -- 2,2 3,2 3,2 4,6 3,9 4,3 4,1 4,6 4,4 4,3 4 4,6Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Face-to-face dimension ETE series 1 according to DIN EN 12982Weights Figure-No. DN 15 20 25 32 40 50 65 80 100 125 150 20055.166 (kg) 3,8 4,2 4,8 5,6 7,8 10 12,8 18,9 45 55,3 73 183Figure-No. Nominal pressure Material Nominal diameter55.166....111 PN40 1.4581 DN15-20055.166....112 PN40 1.4581 DN15-200Butt weld ends according to DIN EN 12627 - 4 (refer to page 20)Test: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Recycling facilities, Chemical industry, Processing technology, Process water installations, Installations with aggressive media, etc.(other applications on request) Selection of possible flow media Aggressive media, etc.(other flow media on request) Bonnet DN200one-piece stem Bonnet DN200two-piece stem ARI-FABA®-Supra IFig. 16617Edition 01/11 - Data subject to alterationStop valve - Y-pattern with butt weld ends and bellows seal - Chemical version (Stainless steel) Fig. 166....153 DN15-150one-piece stem Fig. 166....154 DN15-150two-piece stemFigure-No. Nominal pressure Material Nominal diameter55.166....153 PN40 1.4581 DN15-20055.166....154 PN40 1.4581 DN15-200Butt weld ends according to DIN EN 12627 - 4 (refer to page 20)Test: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Recycling facilities, Chemical industry, Process pipes, Processing technology, Process water installations, Installations with aggressive media, etc.(other applications on request) Selection of possible flow media Aggressive media, Chemical products, etc.(other flow media on request) Bonnet DN200one-piece stem Bonnet DN200two-piece stem ARI-FABA®-Supra CFig. 166PartsPos. Description Fig. 55.166....153 One-piece stem Fig. 55.166....154 Two-piece stem1 Body GX5CrNiMoN19-11-2, 1.45812 Bonnet =DN150: GX5CrNiMo19-11-2, 1.4408 / =DN200: X6CrNiMoTi17-12-2, 1.4571 3 Plug * X6CrNiMoTi17 12 2, 1.4571 / Stellit 64.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud A4-708 Hexagon nut A49 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 existsThe engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200L (mm) 130 150 160 180 200 230 290 310 350 400 480 600H2 (One-piece stem) (mm) 210 210 220 220 270 270 310 385 455 500 590 795H2 (Two-piece stem) (mm) 225 225 230 230 285 285 365 400 490 535 615 840ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520B (One-piece stem) (mm) 110 85 85 70 95 65 50 125 185 170 180 255B (Two-piece stem) (mm) 120 95 90 75 110 80 75 135 210 200 205 290Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50Kvs-value (m3/h) 5,5 8 12,5 17 28 42 72 100 150 239 360 595Zeta-value -- 2,7 4 4 5,8 5,2 5,7 5,5 6,5 7,1 6,8 6,2 7,2Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Face-to-face dimension ETE series 1 according to DIN EN 12982Weights Figure-No. DN 15 20 25 32 40 50 65 80 100 125 150 20055.166 (kg) 3,8 4,2 4,8 5,6 7,8 10 12,8 18,9 45 55,3 73 183Edition 01/11 - Data subject to alteration18Stop valve - angle pattern with flanges and bellows seal - Industrial version (Cast steel) Fig. 147....111 DN15-150one-piece stem Fig. 147....112 DN15-150two-piece stemFigure-No. Nominal pressure Material Nominal diameter34.147....111 PN25 1.0619+N DN200-30035.147....111 PN40 1.0619+N DN15-15034.147....112 PN25 1.0619+N DN200-30035.147....112 PN40 1.0619+N DN15-150Test: • TA - Luft TÜV-Test-No. 973-10183778 Plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) Bonnet DN200-300one-piece stem Bonnet DN200-300two-piece stem PartsPos. Description Fig. 34. / 35.147....111 One-piece stem Fig. 34. / 35.147....112 Two-piece stem1 Body GP240GH+N, 1.0619+N1.2 Seat G19 9 NbSi, 1.45512 Bonnet =DN150: GP240GH+N, 1.0619+N / =DN200: P250 GH, 1.0460; P235GH-TC1, 1.0345; P265 GH, 1.04253 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)25 Guide bush =DN32: X6CrNiMoTi17 12 2, 1.4571 / =DN40: GX5CrNiMo19-11-2, 1.440837 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200 250 300l (mm) 90 95 100 105 115 125 145 155 175 200 225 275 325 375H3 (One-piece stem) (mm) 210 210 215 215 255 255 275 350 420 450 510 720 835 915H3 (Two-piece stem) (mm) 225 225 225 225 275 275 310 365 465 500 545 745 835 915ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520 520 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520 520 520Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50 70 80Kvs-value (m3/h) 6 9 14 19 33 49 85 129 220 350 530 760 1225 1645Zeta-value -- 2,2 3,2 3,2 4,6 3,8 4,2 3,9 3,9 3,3 3,2 2,9 4,4 4,2 4,8Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension CTF Series 8 acc. to DIN EN 558Weights Figure-No. DN 15 20 25 32 40 50 65 80 100 125 150 200 250 30034. / 35.147 (kg) 5,2 7 7,5 8,3 11,1 14,2 20,3 27 46,5 59 67 180 270 347ARI-FABA®-Supra IFig. 147Edition 01/11 - Data subject to alteration19Edition 01/11 - Data subject to alterationStop valve - angle pattern with flanges and bellows seal - Chemical version (Cast steel) Fig. 147....153 DN15-150one-piece stem Fig. 147....154 DN15-150two-piece stemFigure-No. Nominal pressure Material Nominal diameter34.147....153 PN25 1.0619+N DN200-30035.147....153 PN40 1.0619+N DN15-15034.147....154 PN25 1.0619+N DN200-30035.147....154 PN40 1.0619+N DN15-150Test: • TA - Luft TÜV-Test-No. 973-10183778 V-port plug with marginal seat standardAt high differential pressures a balancing plug is necessary (refer to page 21) Selection of possible applications Industry, Power plant, Flue gas purification plant, Processing technology, Gas supply, Vapour facilities, Recycling facilities, Vacuum plant, Thermaloil-systems, General plant manufacturing, etc. (other applications on request) Selection of possible flow media Steam, Gases, Hot water, Heat transfer oil, Ammonia, etc.(other flow media on request) Bonnet DN200one-piece stem Bonnet DN200two-piece stem PartsPos. Description Fig. 34. / 35.147....153 One-piece stem Fig. 34. / 35.147....154 Two-piece stem1 Body GP240GH+N, 1.0619+N1.2 Seat G19 9 NbSi, 1.45512 Bonnet =DN150: GP240GH+N, 1.0619+N / =DN200: P250 GH, 1.0460; P235GH-TC1, 1.0345; P265 GH, 1.04253 Plug * X20Cr13+QT, 1.4021+QT (hardened)4.1 Bellows seal X6CrNiMoTi17 12 2, 1.45714.2 Stem X6CrNiMoTi17 12 2, 1.45715 Handwheel * =DN125: St (cataphoretic coating) / =DN150: EN-GJS-400-15, EN-JS1030 (epoxy-coating)EN-GJS-400-15, EN-JS1030 (epoxy-coating)6 Packing ring Pure graphite7 Stud 25CrMo4, 1.72188 Hexagon nut C35E, 1.11819 Gasket * Pure graphite (with CrNi-grooved)44 Stem, top -- X39CrMo17-1+QT, 1.4122+QT* Spare partInformation / restriction of technical rules need to be observedOperating instructions can be ordered by phone +49 (0)5207 / 994-0 or fax +49 (0)5207 / 994-158 or -159. A production allowance acc. to TRB 801 No. 45 exists The engineer, designing a system or a plant, is responsible for the selection of the correct valve.DimensionsDN 15 20 25 32 40 50 65 80 100 125 150 200 250 300l (mm) 90 95 100 105 115 125 145 155 175 200 225 275 325 375H3 (One-piece stem) (mm) 210 210 215 215 255 255 275 350 420 450 510 720 835 915H3 (Two-piece stem) (mm) 225 225 225 225 275 275 310 365 465 500 545 745 835 915ØC (One-piece stem) (mm) 125 125 125 125 150 150 175 225 300 300 400 520 520 520ØC (Two-piece stem) (mm) 140 140 140 140 160 160 180 225 300 300 400 520 520 520Travel (mm) 6 6 8 8 13 13 16 20 25 32 40 50 70 80Kvs-value (m3/h) 5,5 8 12,5 17 28 42 80 100 155 245 370 530 850 1140Zeta-value -- 2,7 4 4 5,8 5,2 5,7 4,5 6,5 6,6 6,5 5,9 9,1 8,6 10Zeta-value ... range of tolerance for Kvs-values acc. to VDI/VDE 2173 Standard-flange dimensions refer to page 25Face-to-face dimension CTF Series 8 acc. to DIN EN 558Weights Figure-No. DN 15 20 25 32 40 50 65 80 100 125 150 200 250 30034. / 35.147 (kg) 5,2 7 7,5 8,3 11,1 14,2 20,3 27 46,5 59 67 180 270 347ARI-FABA®-Supra IFig. 147Edition 01/11 - Data subject to alteration20ARI-FABA®-SupraPlug - designARI-FABA®-Supra IIsolation plug with marginal seat, stelllitedPlug with soft seal Max. operating temperature 200°C at PTFE + 25% carbonRegulating plug with marginal seat Regulating plug with soft seal Max. operating temperature 200°C at PTFE + 25% carbon ARI-FABA®-Supra CV-port plug with marginal seat, stelllitedV-port plug with soft seal Max. operating temperature 200°C at PTFE + 25% carbonV-port regulating plug with marginal seat V-port regulating plug with soft seal Max. operating temperature 200°C at PTFE + 25% carbon21ARI-FABA®-SupraPlug - designValves with balancing plugs have to be installed with medium flowing over the plug (3) as indicated by flow direction arrow on valve body and the stem is vertically upright. Working principles: When the valve is closed, anticlockwise rotation of the hand wheel lifts the pilot plug (3.1) off the larger balancing plug (3). This allows the medium to pass through the plug and equalizes the pressure of the medium under the plug (3). After the pressures have been equalized within the values stated in the table, the valve can be opened by turning the valve further with normal manual force. Balancing plugs are fully effective only in closed systems. The pressures of the medium on either side of the plug can not be equalized if the medium is discharged into open air. A bypass line or some other arrangement is necessary if too much time is required for pressure equalization owing to the volume in the piping system. ARI-stop valves with differential pressures exceeding the following pressures, have to be fitted with pressure balancing plugs DN 125 150 200 250 300 350 400 500Differential pressure (?P) (bar) 25 21 14 9 6 4,5 3,5 1,5Edition 06/12 - Data subject to alterationFlow directionEdition 01/11 - Data subject to alteration22Limit switch Hood valve acc.to DIN EN 12828 (tamper-proof handwheel cover, only construction with one-piece stem)Size DN ØC ØC1(mm) (mm) (mm)I 15-50 125 170II 65-80 150 190III 100-150 225 330Handwheel-Ø from DN 65 reducedChain wheelDN ØC2 Weight(mm) (mm) (kg)15-32 180 2,540-80 220 7100-150 260 8,9200-400 300 11Stem extension (please specify height in your order)Lubricating nipple / Locking device / Travel limiter (only construction with one-piece stem) Travel limiter (Accessories are not included )DN Hexagon bolt(mm) (mm x mm)15-80 M8 x 55100 M12 x 70125-150 M12 x 80200 M12 x 100250-300 M12 x 120350-400 M16 x 160ARI-FABA®-SupraFunctions / special design / accessoriesAccessories: Travel limiterLubricating nippleLocking deviceOne-piece stem Two-piece stemOne-piece stem Two-piece stem23Edition 01/11 - Data subject to alterationPneumatic actuator ARI-FA Pneumatic actuator ARI-FASpring closes Pneumatic actuator ARI-FASpring opens on air failureImportant: The pneumatic actuator ARI-FA can be combined with all ARI-FABA-Supra versions with two-piece stem Max. medium temperatur in the valve 250°C Not aplicable for design with balancing plugs ARI-FABA®-SupraPneumatic actuator ARI-FAPartsPos. Description Material1 Stem X20Cr13+QT, 1.4021+QT2 Head X20Cr13+QT, 1.4021+QT4 O-ring * NBR5 Lock nut 5.8 - A2G6 O-ring * NBR7 Guiding band * PTFE -+25%C8 Lower diaphragm casing DD13+QT, 1.0335+QT (powder coated)9 Upper diaphragm casing DD13+QT, 1.0335+QT (powder coated)10 Spring * FDSiCr11 Rolling diaphragm * NBR + webbing12 Diaphragm plate DD13+QT, 1.0335+QT (Fe/Zn12B)13 Diaphragm flange DD13+QT, 1.0335+QT (Fe/Zn12B)14 Collar nut * 8 - A4G15 Hexagon bolt 8.8 - A4G16 Hexagon nut 8 - A4G17 Vent plug * Polyäthylen* Spare partType of actuator FA160 FA250 FA400 FA800Ø A (mm) 210 250 300 405H(x) (mm) refert to page 2 -19max. H4 (mm) 90 105 120 165max. pressure (bar) 6 6 6 6Weight (actuator) (kg) 6,5 9 17 5024Edition 01/11 - Data subject to alterationmax. permissible closing pressures on flow-to-open P2 = 0 (Observe regulations, refer to page 25.)Spring closesDN 15 20 25 32 40 50 65 80 100 125 150Travel (mm) 6 6 8 8 13 13 16 20 25 32 40Actuator FA160Air supply pressure min. (bar)4 40 40 26,7 18Actuator FA2504,5 40 20,5 11,1 1,6Actuator FA4004,5 40 31 14,8 6,5 1,4Actuator FA8005 17,4 8,9 4,3Req. air supply press. for pneumatic actuators FA: max. permissible 6 barmax. permissible closing pressures on flow-to-open P2 = 0 (Observe regulations, refer to page 25.)Spring opens on air failureDN 15 20 25 32 40 50 65 80 100 125 150Travel (mm) 6 6 8 8 13 13 16 20 25 32 40Actuator FA160Air supply pressure min. (bar)3 40 40 21,1 13,74 40 40 40 31,95 40 40 40 406 40 40 40 40Actuator FA2503 38,4 13,8 6,94 40 30 17,3 6,25 40 40 27,8 12,56 40 40 38,2 18,7Actuator FA4003 9,6 3,94 19,6 10,5 4,75 29,6 17,1 96 39,5 23,8 13,2Actuator FA8003 10,4 4,5 1,84 18,9 10 5,65 27,5 15,5 9,46 36 21 13,2Req. air supply press. for pneumatic actuators FA: max. permissible 6 barARI-FABA®-Supra Closing pressures: Pneumatic actuator ARI-FA25Edition 01/11 - Data subject to alterationStandard-flange dimensions Flanges acc. to DIN EN 1092-1/-2 (Flangeholes / -thickness tol. acc. To DIN 2533/2544/2545)DN (mm) 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400 500PN25 ØD (mm) 95 105 115 140 150 165 185 200 235 270 300 360 425 485 555 620 730PN25 ØK (mm) 65 75 85 100 110 125 145 160 190 220 250 310 370 430 490 550 660PN25 n x Ød (mm) 4x14 4x14 4x14 4x18 4x18 4x18 8x18 8x18 8x22 8x26 8x26 12x26 12x30 16x30 16x33 16x36 20x36PN40 ØD (mm) 95 105 115 140 150 165 185 200 235 270 300 375 450 515 580 660 755PN40 ØK (mm) 65 75 85 100 110 125 145 160 190 220 250 320 385 450 510 585 670PN40 n x Ød (mm) 4x14 4x14 4x14 4x18 4x18 4x18 8x18 8x18 8x22 8x26 8x26 12x30 12x33 16x33 16x36 16x39 20x42Pressure-temperature-ratings acc. to manufacturers standardMaterial -60°C to <-10°C* -10°C to 120°C 150°C 200°C 250°C 300°C 350°C 400°C 450°C1.0619+N 25 (bar) 18,7 25 23,9 22 20 17,2 16 14,8 8,21.0619+N 40 (bar) 30 40 38,1 35 32 28 25,7 23,8 13,11.0460 25 (bar) 18,7 25 23,9 22 20 17,2 16 14,8 101.0460 40 (bar) 30 40 38,1 35 32 28 25,7 23,8 16Pressure-temperature-ratings acc. to DIN EN 1092-1Material -60°C to <-10°C* -10°C to 100°C 150°C 200°C 250°C 300°C 350°C 400°C 450°C1.4408 25 (bar) 25 25 22,7 21 19,8 18,5 17,8 17,1 --1.4408 40 (bar) 40 40 36,3 33,7 31,8 29,7 28,5 27,4 --1.4581 25 (bar) 12,5 25 24,5 23,3 22,1 20,8 20,1 19,5 --1.4581 40 (bar) 20 40 39,2 37,3 35,4 33,3 32,1 31,2 --Intermediate values for max. permissible operational pressures can be determined by linear interpolation of the given temperature / pressure chart.* Studs and nuts made of A4-70 (at temperatures below -10°C)Please indicate when ordering- Figure-No. - Nominal pressure- Nominal diameter- Special design / accessoriesExample:Figure 35.146; nominal pressure PN40; nominal diameter DN100.Dimensions in mmWeights in kg1 bar =^ 105 Pa =^ 0,1 MPa Kvs in m3/h ARI-FABA®-Supra Flange dimensions / Pressure-temperature-ratings26 Edition 01/11 - Data subject to alterationButt weld ends according to DIN EN 12627 - 4DN 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400L (mm) 130 150 160 180 200 230 290 310 350 400 480 600 730 850 980 1100ØA (mm) 22 28 35 44 50 62 77 91 117 144 172 223 278 329 362 413ØB (mm) 17,3 22,3 28,5 37,2 43,1 53,9 68,9 80,9 104,3 130,7 157,1 204,9 257, 307,9 338, 384,4Ødi (mm) 15 20 25 32 40 50 65 80 100 125 150 200 250 300 330 375R (mm) 3 3 3 3 3 3 3 3 3 3 3 5 5 5 5 5L1 (mm) 10 10 10 10 10 10 10 12 14 18 20 20 25 33 45 45Ød3 (mm) 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273 323,9 355,6 406,4s1 (mm) 2 2,3 2,6 2,6 2,6 3,2 3,6 4 5 4,5 5,6 7,1 8 8 8,8 11Shoed ends of P235GH (Pipe connection =^ welding neck flanges)DN 15 20 25 32 40 50 65 80 100 125 150 200 250 300 350 400Ød (mm) -- -- -- -- -- -- 76,1 88,9 114,3 139,7 168,3 219,1 -- -- -- --Øs (mm) -- -- -- -- -- -- 2,9 3,2 3,6 4 4,5 6,3 -- -- -- --Face-to-face dimension ETE series 1 according to DIN EN 12982.Butt weld ends according to DIN EN 12627 - 4. Weld joint according to DIN EN 29692 code numer 1.3.3. The material used for ARI valves with butt weld ends are: GP240GH+N, 1.0619+N acc. to DIN EN 10213-2, P250GH, 1.0460 acc. to DIN EN 10222-2.The material used for ARI valves with shoed ends (DN 65-200) P235GH according to DIN EN 10216-2.Based on our experience we recommend electric welding process for connecting valves or strainers with tubes or with each other Lime based electrodes with an appropriate composite material should be used as filler material for welding.Gas welding should be avoided. Due to the different material composition and material thickness of valves and tubes, gas welding is more susceptible to produce faults than electric welding (hardness cracks, coarse-grained structure).L = Face-to-face dimensionEdge shaping acc. to DIN EN ISO 5817ARI-FABA®-Supra Valves with butt weld endsTechnology for the Future. G E R M A N Q U A L I T Y V A L V E SARI-Armaturen Albert Richter GmbH & Co. KG, D-33756 Schloß Holte-Stukenbrock, Tel. +49 52 07 / 994-0, Telefax +49 52 07 / 994-158 or 159 Internet: http://www.ari-armaturen.com E-mail: info.vertrieb@ari-armaturen.com ARI-FABA®-Supra Stop valve with bellows seal ARI-FABA®-Supra I Stop valve - straight through with flanges and bellows seal - Industrial version (Cast steel) Stop valve - straight through with flanges and bellows seal - Industrial version (Forged steel) Stop valve - straight through with flanges and bellows seal - Industrial version (Stainless steel) Stop valve - Y-pattern with butt weld ends and bellows seal - Industrial version (Stainless steel) Stop valve - straight through with butt weld ends and bellows seal - Industrial version (Cast steel) Stop valve - Y-pattern with flanges and bellows seal - Industrial version (Stainless steel) Stop valve - Y-pattern with butt weld ends and bellows seal - Industrial version (Cast steel) Stop valve - Y-pattern with butt weld ends and bellows seal - Industrial version (Stainless steel) Stop valve - angle pattern with flanges and bellows seal - Industrial version (Cast steel) ARI-FABA®-Supra C Stop valve - straight through with flanges and bellows seal - Chemical version (Cast steel) Stop valve - straight through with flanges and bellows seal - Chemical version (Forged steel) Stop valve - straight through with flanges and bellows seal - Chemical version (Stainless steel) Stop valve - straight through with butt weld ends and bellows seal - Chemical version (Forged steel) Stop valve - straight through with butt weld ends and bellows seal - Chemical version (Cast steel) Stop valve - Y-pattern with flanges and bellows seal - Chemical version (Stainless steel) Stop valve - Y-pattern with butt weld ends and bellows seal - Chemical version (Cast steel) Stop valve - Y-pattern with butt weld ends and bellows seal - Chemical version (Stainless steel) Stop valve - angle pattern with flanges and bellows seal - Chemical version (Cast steel) Plug - design Isolation plug with marginal seat; stellited seat and plug Plug with soft seal Regulating plug with marginal seat Regulating plug with soft seal V-port plug with marginal seat, stelllited V-port plug with soft seal V-port regulating plug with marginal seat V-port regulating plug with soft seal Balancing plug Accessories Limit switch Hood valve Chain wheel Stem extension Lubricating nipple / Locking device / Travel limiter Pneumatic actuator ARI-FA Closing pressures Standard-flange dimensions Pressure-temperature-ratings Valves with butt weld ends ARI-FABA®-LongLife ARI-FABA®-LongLife Stainless steel ARI-FABA®-Plus ARI-FABA®-Plus/-Supra ANSI