Autoclave Pumps Brochure

Manual Operation • Pump comes standard with hand lever for precise pressure control, remote locations or emergency back-up applications.Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility. • Maximum Outlet Pressure: 31,900 psi (2,200 bar) • Maximum Air to Liquid Pressure Ratio: 1:213 • Volume Displacement Per Stroke: 0.035 in3 (.57 cm3) • Inlet Connection: 3/8" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Pump can be operated with air even with manual hand lever attached • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 31,900 psi (2,200 bar) output pressure is 148 psi (10 bar) • Inlet Port: 1/4" FNPT • Exhaust Port (muffler removed): 1/4" FNPT • Air Consumption @ 90 psi: 13 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 9 lbs. (4.1 kg) • Pressure Head: 316 Stainless Steel • Plunger: 440 Stainless Steel • Check Valve Glands: 15-5PH Stainless Steel • Liquid Seal: See Ordering Guide for options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comHand Lever/Air Driven, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive w/ Hand Lever Series ACHL189-01Single-Acting, Single Piston Air Drive w/ Hand Lever Bottom Inlet ShownMADE IN THE U.S.A.0501001502002500 200 400 600 800 1000 1200 1400 160002468101214160 5000 10000 15000 20000 25000FLOW RATE (IN3 /MIN)OUTLET PRESSURE (PSI)CHARTED FLOW RATES ARE FOR 1-10 CST FLUIDSAIR DRIVE PRESSURE60 PSI      90 PSI      120 PSI[4 BAR]   [6 BAR]     [8 BAR]OUTLET PRESSURE (BAR)FLOWRATE (CM3/MIN)120 PSI[8 BAR]90 PSI[6 BAR]60 PSI[4 BAR]Technical Specifications & Performance Data Hand Lever/Air- Driven, High Pressure Liquid Pump - Series ACHL189-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ACHL189-01SNPACHL = • Compact Liquid High Pressure Pump w/ Hand Lever • 3" Single Piston Air Drive • 1:213 Maximum Air-to-Liquid Pressure Ratio • Maximum 31,900 psi (2,200 bar)ACHL189-01 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialPump Type / Size / RatioACHL189-01 Series Air Pressure Stall Pressure Hand Lever Force (PSI) (PSI) (LBF) 20 3435 12 40 7890 21 60 12350 30 80 16810 39 100 21265 48 120 25725 57 148 31900 70Stall Pressure Note:The pump's air piston is returned using a coilspring. Depending on the position of the piston during stall stroke, the stall pressure can vary ±350 psi from the values shown on the chart. For precise pressure control, Autoclave recom-mends using the manual hand lever.* S = Side B = Bottom *Standard for Stock Pumps* N = None * P = UHMWPE U-Cup with Elgiloy Spring Energizer U = Urethane U-CupTechnical Specifications & Performance DataHand Lever/Air- Driven, High Pressure Liquid Pump - Series ACHL189-01Dimensional Data: Left View Front ViewRight View Back ViewNote: Each Mounting Bracket includes (2) 11/32" (8.73) holes for 5/16" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)1.71(43.5)11.40(289.5)13.49(342.6)3.34(84.8)14.69(373.1)1.00(25.4)0.75(19.1)6.06(154.0)Outlet6.80(172.7)SideInlet8.81(223.7)BottomInletSee Note5.95(151.3)Bracket Slot SpacingSee Note1.63(41.3)1.31(33.3)1.42(36.2)0.23(5.8)1/4” NPTAir Drive Inlet2.47(62.7)5.19(131.8)Liquid InletFemale 3/8” NPTLiquid OutletAutoclave EngineersF250C - 1/4” FemaleHigh PressureConnection Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 31,900 psi (2,200 bar) • Air to Liquid Pressure Ratio: 1:220 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.04 in3 (.66 cm3) • Inlet Connection: 3/8" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 31,900 psi (2,200 bar) output pressure is 145 psi (10 bar) • Inlet Port: 1/4" FNPT • Exhaust Port (muffler removed): 1/4" FNPT • Air Consumption @ 90 psi: 13 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 8 lbs. (3.6 kg) • Net Weight with Isolation Chamber: 11 lbs. (5.0 kg) • Pressure Head: 316 Stainless Steel • Plunger: 440 Stainless Steel • Check Valve Glands: 15-5PH Stainless Steel • Liquid Seal: See Ordering Guide for options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ACL189-01Single-Acting, Single Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ACL189-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ACL189-01SNPACL = • Compact Liquid High Pressure Pump • 3" Single Piston Air Drive • 1:220 Air-to-Liquid Pressure Ratio • Maximum 31,900 psi (2,200 bar)* S = Side B = BottomACL189-01 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialPump Type / Size / RatioACL189-01 Series*Standard for Stock Pumps* N = None C = Included* P = UHMWPE U-Cup with Elgiloy Spring Energizer U = Urethane U-CupTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ACL189-01Dimensional Data: Left ViewFront ViewRight ViewRight View with Optional Isolation Chamber4.69 (119.00)Note: Each Mounting Bracket includes (2) x 3/8" (9.53) Slots for 5/16" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)See NotePilot Valve Vent 6.11 (155.09)Bracket SlotSpacingSee Note1.81 (45.97)1.97(49.99)Slot Spacing Both Brackets3.40 (86.44)3.79 (96.34)See Note5.19 (131.83)Side Inlet2.47 (62.74)Liquid Outlet Autoclave Engineers F250C - 1/4" Female High Pressure ConnectionLiquid Inlet Female 3/8" NPT1/4" NPTAir Drive Inlet4.06 (103.12)0.48 (12.10)1.52 (38.49)6.07 (154.09) Outlet6.80 (172.72)Side Inlet8.81 (223.77)Bottom Inlet0.48 (12.10)6.07 (154.09) Drain7.76 (197.10)8.49(215.65)Side Inlet10.19 (258.83)Bottom Inlet1/8" FNPTDrain PortIsolation Chamber Pump Head.32(8.13)Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 15,000 psi (1034 bar) • Air to Liquid Pressure Ratio: 1:113 • Isolation Chamber (prevents process contamination of air section): Standard • Volume Displacement Per Stroke: 2.30 in3 (37.7 cm3) • Inlet Connection: 1" NPT • Outlet Connection: Parker Autoclave Engineers SF562CX20-9/16" Female Medium Pressure (Contact Parker Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note • Nominal air pressure required for 15,000 psi (1034 bar) output pressure is 132.75 psi (9.15 bar) • Inlet Port: 3/4" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1" NPT • Max Air Consumption @ 90 psi: 167 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight: 41 lbs. (18.6 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Note: Maximum air drive pressure is limited by maximum output pressure. Air-Driven, High Pressure Liquid PumpDouble-Acting, Single Ended, Single Piston Air Drive Series AFL100-1DDouble-Acting, Single Piston Air DriveMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series AFL100-1DFlow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Parker Autoclave Engineers. Typical catalog number: AFL100-1DBCXXAFL = • High Flow High Pressure Pump • 6" Single Piston Air Drive • 1:113 Air-to-Liquid Pressure Ratio • Maximum 15,000 psi (1034 bar) • Single Ended, Double Acting Liquid HeadAFL100-1D BLiquid Inlet LocationCIsolationChamberPVLiquid SealMaterialPump Type / Size / RatioAFL100-1D Series*B = Bottom * PV = UHMWPE U-Cup with Vitron O-rings PE = UHMWPE U-Cup with EPDM O-rings PB = UHMWPE U-Cup with Buna-N O-rings PC = UHMWPE U-Cup with Perfluoroelastomer O-rings*Standard for Stock Pumps*C = IncludedTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series AFL100-1DDimensional Data: Right ViewFront ViewBottom ViewLeft ViewNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)9.86 (250.36)5.81 (147.49)2.40 (60.95)9.46 (240.40)11.28 (286.54)11.81 (299.95) 13.37 (399.55)24.09 (611.91)Liquid OutletParker Autoclave EngineersSF562CX20-9/16"Female Medium Pressure3.61(91.61)5.67 (144.06)Isolation Chamber Port 1/8" NPTPilot Air inletFemale 1/8" NPT7.39 (187.79)6.50 (165.10)4.33 (109.98)Slot SpacingBoth BracketsMounting Bracket(2) x 9/16" (14.29)Slots for 1/2" BoltsAir InletFemale 3/4" NPTLiquid InletFemale 1" NPT8.841(215.430)2.103(53.416)Air InletFemale 3/4" NPTLiquid InletFemale 1" NPTTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 6,700 PSI (462 bar) • Air to Liquid Pressure Ratio: 1:67 • Isolation Chamber (prevents process contamination of air section): Standard • Volume Displacement Per Stroke: 15.3 in3 (250.7 cm3) • Dual Inlet Connections: 1" FNPT • Dual Outlet Connections: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 20-100 psi (1.4-6.9 bar) *See note1 • Nominal air pressure required for 6,700 PSI (462 bar) output pressure is 100 psi (6.9 bar) • Inlet Port: 1" female FNPT • Pilot Port: 1/8" female FNPT • Exhaust Ports (mufflers removed): 1" female BSP • Air Consumption @ 50 PSI air (0 PSI liquid): 290 SCFM • Prelubricated at Factorywww.autoclave.comAir-Driven, High Flow, High Pressure Liquid PumpDouble-Acting, Dual Piston Air Drive Series AHL33-2DDouble-Acting, Dual Piston Air Drive MADE IN THE U.S.A.General Specifications • Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight: 160 lbs (73 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for options • Air Drive Seals: Buna NNotes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series AHL33-2DLiquid Flow Rate vs. Outlet Pressure: AHL33-2DSC SeriesNotes: 1. Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type. 2. Flow value at approximately 50 psi air drive pressure.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: AHL33-2DSCUVAHL = • High Flow Liquid High Pressure Pump • 10" Dual Piston Air Drive • 1:67 Air-to-Liquid Pressure Ratio • Maximum 6,700 psi (462 bar) • Double Acting Liquid Heads S = Side C = IncludedAHL33-2D SLiquid Inlet LocationCIsolationChamberUVLiquid SealMaterials†Pump Type / Size / RatioApproximate air drive pressure: 100 psiPressure (PSI) Pressure (bar) Flow (gpm) Flow (liter/min)0 0 7.6*see note 2 28.8 *see note 21000 69 6.1 23.02000 138 5.7 21.53000 207 4.9 18.44000 276 4.0 15.25000 345 3.2 12.36000 414 1.8 6.9Nominal Liquid Pressure (Stalled)Air Drive Pressure Liquid PressurePSI bar PSI bar20 1.4 1340 92.430 2.1 2010 138.640 2.8 2680 184.850 3.4 3350 231.060 4.1 4020 277.270 4.8 4690 323.480 5.5 5360 369.690 6.2 6030 415.8100 6.9 6700 461.9† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" and "T" seal options. "C" seal option is o-ring only, no u-cup. UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings TV = Thermoplastic Polyester U-Cup and Viton O-Rings TE = Thermoplastic Polyester U-Cup and EPDM O-Rings TB = Thermoplastic Polyester U-Cup and Buna-N O-Rings TC = Thermoplastic Polyester U-Cup and Perfluoroelastomer O-Rings C = Perfluoroelastomer O-Rings 1/8" NPT Thread Spool Air Inlet on Middle PlateTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series AHL33-2DDimensional Data: Front View7.00 (177.80)Slot Spacing32.41 (823.21)11.00 (279.40)Liquid InletFemale 1" NPT 17.55 (445.71)Note:Each Mounting Bracket includes (2) x 0.50" (12.7) Slots for 7/16" Bolts.Spool air tubing not shown for clarity.All dimensions are for reference only and are subject to change without notice.Primary Dimensions: Inches Secondary Dimensions: (Millimeters)Side View30.416(772.41)Liquid Outlet Female 1/2" NPT0.50(12.70)Slot Size Type (4) PLCS1" NPT Thread Air Driven Inlet1/8" NPT Thread Spool Air Inlet Opposite Main Air Supply1/4" NPT Thread Isolation Drain PortSee Note8.00 (203.20)8.47 (215.10)16.94 (430.17)18.44 (468.27)See Note1/4" NPT ThreadIsolation Drain Port5.50 (139.70)13.38 (339.70)Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 13,300 PSI (917 bar) • Air to Liquid Pressure Ratio: 1:133 • Isolation Chamber (prevents process contamination of air section): Standard • Volume Displacement Per Stroke: 7.8 in3 (127.8 cm3) • Dual Inlet Connections: 1/2" FNPT • Dual Outlet Connections: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 20-100 psi (1.4-6.9 bar) *See note1 • Nominal air pressure required for 13,300 PSI (917 bar) output pressure is 100 psi (6.9 bar) • Inlet Port: 1" female FNPT • Pilot Port: 1/8" female FNPT • Exhaust Ports (mufflers removed): 1" female BSP • Air Consumption @ 50 PSI air (0 PSI liquid): 290 SCFM • Prelubricated at Factorywww.autoclave.comAir-Driven, High Flow, High Pressure Liquid PumpDouble-Acting, Dual Piston Air Drive Series AHL66-2DDouble-Acting, Dual Piston Air Drive MADE IN THE U.S.A.General Specifications • Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight: 160 lbs (73 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for options • Air Drive Seals: Buna NNotes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series AHL66-2DLiquid Flow Rate vs. Outlet Pressure: AHL66-2DSC SeriesNotes: 1. Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type. 2. Flow value at approximately 50 psi air drive pressure.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: AHL66-2DSCUVAHL = • High Flow Liquid High Pressure Pump • 10" Dual Piston Air Drive • 1:133 Air-to-Liquid Pressure Ratio • Maximum 13,300 psi (917 bar) • Double Acting Liquid Heads S = Side C = IncludedAHL66-2D SLiquid Inlet LocationCIsolationChamberUVLiquid SealMaterials†Pump Type / Size / RatioApproximate air drive pressure: 100 psiPressure (PSI) Pressure (bar) Flow (gpm) Flow (liter/min)0 0 3.6*see note 2 13.7 *see note 21000 69 3.4 12.92000 138 3.1 12.03000 207 2.9 11.24000 276 2.7 10.35000 345 2.5 9.56000 414 2.3 8.77000 483 2.2 8.28000 552 2.0 7.79000 621 1.8 6.710000 690 1.5 5.711000 759 1.3 4.812000 828 1.0 3.9 Nominal Liquid Pressure (Stalled)Air Drive Pressure Liquid PressurePSI bar PSI bar20 1.4 2660 183.430 2.1 3990 275.240 2.8 5320 366.950 3.4 6650 458.660 4.1 7980 550.370 4.8 9310 642.180 5.5 10640 733.890 6.2 11970 825.5100 6.9 13300 917.2† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" and "T" seal options. "C" seal option is o-ring only, no u-cup. UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings TV = Thermoplastic Polyester U-Cup and Viton O-Rings TE = Thermoplastic Polyester U-Cup and EPDM O-Rings TB = Thermoplastic Polyester U-Cup and Buna-N O-Rings TC = Thermoplastic Polyester U-Cup and Perfluoroelastomer O-Rings C = Perfluoroelastomer O-Rings 1/8" NPT Thread Spool Air Inlet on Middle PlateTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series AHL66-2DDimensional Data: Front View7.00 (177.80)Slot Spacing32.66 (829.61)11.00 (279.40)Liquid Inlet Female 1/2" NPT 17.55 (445.71)Note:Each Mounting Bracket includes (2) x 0.50" (12.7) Slots for 7/16" Bolts.Spool air tubing not shown for clarity.All dimensions are for reference only and are subject to change without notice.Primary Dimensions: Inches Secondary Dimensions: (Millimeters)Side View30.16(766.11)Liquid Outlet Female 1/2" NPT0.50(12.70)Slot Size Type (4) PLCS1" NPT Thread Air Driven Inlet1/8" NPT Thread Spool Air Inlet Opposite Main Air Supply1/4" NPT Thread Isolation Drain PortSee Note8.00 (203.20)8.47 (215.10)16.94 (430.17)18.44 (468.27)See Note1/4" NPT ThreadIsolation Drain Port5.50 (139.70)13.38 (339.70)Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 1,600 psi (110 bar) • Air to Liquid Pressure Ratio: 1:11 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 5.22 in3 (85.5 cm3) • Inlet Connection: 1" FNPT • Outlet Connection: 1/2" FNPT Female NPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 1,600 psi (110 bar) output pressure is 145 psi (10 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 69 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 38 lbs. (17.2 kg) • Net Weight with Isolation Chamber: 50 lbs. (22.7 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Flow, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL10-01Single-Acting, Single Piston Air Drive Pump Bottom Inlet ShownMADE IN THE U.S.A.0.02.04.06.08.010.012.014.016.018.020.022.024.00.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.00.00.51.01.52.02.53.03.54.04.55.05.56.06.50 200 400 600 800 1000 1200 1400FLOW RATE (GPM)OUTLET PRESSURE (PSI)CHARTED FLOW RATES ARE FOR 1-10 CST FLUIDSAIR DRIVE PRESSURE60 PSI      90 PSI      120 PSI[4 BAR]   [6 BAR]     [8 BAR]OUTLET PRESSURE (BAR)FLOWRATE (L/MIN)120 PSI[8 BAR]90 PSI[6 BAR]60 PSI[4 BAR]Technical Specifications & Performance Data Air- Driven, High Flow, High Pressure Liquid Pump - Series ASL10-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL10-01SNPVASL = • Standard Liquid High Flow, High Pressure Pump • 6" Single Piston Air Drive • 1:11 Air-to-Liquid Pressure Ratio • Maximum 1,600 psi (110 bar)ASL10-01 SLiquid Inlet LocationNIsolationChamberPVLiquid SealMaterials†Pump Type / Size / RatioASL10-01 Series* N = None C = Included* S = Side B = Bottom*Standard for Stock Pumps† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" and "T" seal options. UHMWPE u-cup seals comes with a stainless steel spring energizer.* PV = UHMWPE U-Cup and Viton O-Rings PE = UHMWPE U-Cup and EPDM O-Rings PB = UHMWPE U-Cup and Buna-N O-Rings PC = UHMWPE U-Cup and Perfluoro- elastomer O-Rings UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings TV = Thermoplastic Polyester U-Cup and Viton O-Rings TE = Thermoplastic Polyester U-Cup and EPDM O-Rings TB = Thermoplastic Polyester U-Cup and Buna-N O-Rings TC = Thermoplastic Polyester U-Cup and Perfluoroelastomer O-Rings Technical Specifications & Performance DataAir-Driven, High Flow, High Pressure Liquid Pump - Series ASL10-01Dimensional Data: Left View Front ViewRight ViewNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)1/8” FNPT ExternalPilot Connection10.60(269.2)5.03(127.9)1.19(30.2)Pilot Valve Vent3.41(86.7)7.50(190.5)6.38(162.1)3.12(79.2)Slot SpacingBoth BracketsSee NoteLiquid OutletFemale 1/2” NPT3.27(83.0)7.57(192.4)Liquid InletFemale 1” NPT7.84(199.2)1/2” FNPTAir Drive Inlet0.47(11.9)See Note0.99(25.2)See Note12.20(309.88)Bottom Inlet9.83(249.7)Side Inlet6.87(174.5)Bracket SlotSpacing8.25(209.6)Right View with Optional Isolation Chamber1/8” FNPTDrainPortIsolationChamber7.84(199.2)1/2” FNPTAir Drive Inlet0.47(11.9)See Note0.99(25.2)16.15(410.21)Bottom Inlet13.78(350.01)Side Inlet12.20(309.88)Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibilty • Maximum Outlet Pressure: 3,200 psi (221 bar) • Air to Liquid Pressure Ratio: 1:22 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 5.22 in3 (85.5 cm3) • Inlet Connection: 1" FNPT • Outlet Connection: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 3,200 psi (221 bar) output pressure is 145 psi (10 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 61 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 49 lbs. (22.2 kg) • Net Weight with Isolation Chamber: 61 lbs. (27.1 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL10-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL10-02Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL10-02SNPVASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:22 Air-to-Liquid Pressure Ratio • Maximum 3,200 psi (221 bar)ASL10-02 SLiquid Inlet LocationNIsolationChamberPVLiquid SealMaterials†Pump Type / Size / Ratio* N = None C = Included* S = Side B = Bottom*Standard for Stock Pumps† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" and "T" seal options. UHMWPE u-cup seals comes with a stainless steel spring energizer.ASL10-02 Series* PV = UHMWPE U-Cup and Viton O-Rings PE = UHMWPE U-Cup and EPDM O-Rings PB = UHMWPE U-Cup and Buna-N O-Rings PC = UHMWPE U-Cup and Perfluoro- elastomer O-Rings UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings TV = Thermoplastic Polyester U-Cup and Viton O-Rings TE = Thermoplastic Polyester U-Cup and EPDM O-Rings TB = Thermoplastic Polyester U-Cup and Buna-N O-Rings TC = Thermoplastic Polyester U-Cup and Perfluoroelastomer O-Rings Technical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL10-02Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets12.19 (309.63)16.14(409.96)BottomInlet3.27 (83.0)See NoteLiquid Inlet Female 1" NPTLiquid OutletFemale 1/2" NPT1/2" FNPT Air Drive InletSee NoteSee Note7.84 (199.18)0.99 (25.20)10.81 (274.60)Bracket SlotSpacingNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)7.57 (192.4)Side inlet13.77 (349.76)SideInlet.47(11.94)1/8" FNPTDrain PortIsolationChamber20.09(510.29)BottomInlet17.72(450.09)SideInlet16.14(409.96)0.47 (11.94)10.60 (269.16)5.03 (127.86)3.41 (86.71)Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 2,300 psi (159 bar) • Air to Liquid Pressure Ratio: 1:16 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 3.62 in3 (59.3 cm3) • Inlet Connection: 1" FNPT • Outlet Connection: 1/2" FNPT Female NPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 2,300 psi (159 bar) output pressure is 144 psi (9.9 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 69 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 38 lbs. (17.2 kg) • Net Weight with Isolation Chamber: 50 lbs. (22.7 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Flow, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL15-01Single-Acting, Single Piston Air Drive Pump Bottom Inlet ShownMADE IN THE U.S.A.0.0002.0004.0006.0008.00010.00012.00014.00016.0000.00 20.00 40.00 60.00 80.00 100.00 120.00 140.000.000.501.001.502.002.503.003.504.004.500 200 400 600 800 1000 1200 1400 1600 1800 2000FLOW RATE (GPM)OUTLET PRESSURE (PSI)CHARTED FLOW RATES ARE FOR 1-10 CST FLUIDSAIR DRIVE PRESSURE60 PSI      90 PSI      120 PSI[4 BAR]   [6 BAR]     [8 BAR]OUTLET PRESSURE (BAR)FLOWRATE (L/MIN)120 PSI[8 BAR]90 PSI[6 BAR]60 PSI[4 BAR]Technical Specifications & Performance Data Air- Driven, High Flow, High Pressure Liquid Pump - Series ASL15-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL15-01SNPVASL = • Standard Liquid High Flow, High Pressure Pump • 6" Single Piston Air Drive • 1:16 Air-to-Liquid Pressure Ratio • Maximum 2,300 psi (159 bar)ASL15-01 SLiquid Inlet LocationNIsolationChamberPVLiquid SealMaterials†Pump Type / Size / RatioASL15-01 Series* N = None C = Included* S = Side B = Bottom* PV = UHMWPE U-Cup and Viton O-Rings PE = UHMWPE U-Cup and EPDM O-Rings PB = UHMWPE U-Cup and Buna-N O-Rings PC = UHMWPE U-Cup and Perfluoro- elastomer O-Rings UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings TV = Thermoplastic Polyester U-Cup and Viton O-Rings TE = ThermoplasticPolyester U-Cup and EPDM O-Rings TB = Thermoplastic Polyester U-Cup and Buna-N O-Rings TC = Thermoplastic Polyester U-Cup and Perfluoroelastomer O-Rings *Standard for Stock Pumps† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" and "T" seal options. UHMWPE u-cup seals comes with a stainless steel spring energizer.Technical Specifications & Performance DataAir-Driven, High Flow, High Pressure Liquid Pump - Series ASL15-01Dimensional Data: Left View Front ViewRight ViewNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)1/8” FNPT ExternalPilot Connection10.60(269.2)5.03(127.9)1.19(30.2)Pilot Valve Vent3.41(86.7)7.50(190.5)6.38(162.1)3.12(79.2)Slot SpacingBoth BracketsSee NoteLiquid OutletFemale 1/2” NPT3.27(83.0)7.57(192.4)Liquid InletFemale 1” NPTRight View with Optional Isolation Chamber7.84(199.2)1/2” FNPTAir Drive Inlet0.47(11.9)See Note0.99(25.2)See Note12.20(309.88)Bottom Inlet9.83(249.7)Side Inlet6.87(174.5)Bracket SlotSpacing8.25(209.6)1/8” FNPTDrainPortIsolationChamber7.84(199.2)1/2” FNPTAir Drive Inlet0.47(11.9)See Note0.99(25.2)16.15(410.21)Bottom Inlet13.78(350.01)Side Inlet12.20(309.88)Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibilty • Maximum Outlet Pressure: 4,600 psi (317 bar) • Air to Liquid Pressure Ratio: 1:32 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 3.62 in3 (59.3 cm3) • Inlet Connection: 1" FNPT • Outlet Connection: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 4,600 psi (317 bar) output pressure is 144 psi (9.9 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 61 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 48 lbs. (21.8 kg) • Net Weight with Isolation Chamber: 60 lbs. (27.2 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL15-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL15-02Flow Rate vs. Outlet Pressure: ASL15-02 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL15-02SNPVASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:32 Air-to-Liquid Pressure Ratio • Maximum 4,600 psi (317 bar)ASL15-02 SLiquid Inlet LocationNIsolationChamberPVLiquid SealMaterials†Pump Type / Size / Ratio* N = None C = Included* S = Side B = Bottom* PV = UHMWPE U-Cup and Viton O-Rings PE = UHMWPE U-Cup and EPDM O-Rings PB = UHMWPE U-Cup and Buna-N O-Rings PC = UHMWPE U-Cup and Perfluoro- elastomer O-Rings UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings TV = Thermoplastic Polyester U-Cup and Viton O-Rings TE = ThermoplasticPolyester U-Cup and EPDM O-Rings TB = Thermoplastic Polyester U-Cup and Buna-N O-Rings TC = Thermoplastic Polyester U-Cup and Perfluoroelastomer O-Rings *Standard for Stock Pumps† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" and "T" seal options. UHMWPE u-cup seals comes with a stainless steel spring energizerTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL15-02Dimensional Data: Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)Left View Front ViewRight ViewRight View with Optional Isolation Chamber1.19 (30.23)1/8" FNPT External Pilot Connection7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets12.19 (309.63)16.14(409.96)BottomInlet3.27 (83.0)See NoteLiquid Inlet Female 1" NPTLiquid OutletFemale 1/2" NPT1/2" FNPT Air Drive InletSee NoteSee Note7.84 (199.18)0.99 (25.20)10.81 (274.60)Bracket SlotSpacing7.57 (192.4)Side inlet13.77 (349.76)SideInlet.47(11.94)1/8" FNPTDrain PortIsolationChamber16.15(410.21)BottomInlet13.78(350.01)SideInlet12.20(309.88)0.47 (11.94)10.60 (269.16)5.03 (127.86)3.41 (86.71)Pilot Valve VentTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 4,000 psi (276 bar) • Air to Liquid Pressure Ratio: 1:28 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 2.10 in3 (34.4 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: 1/2" FNPT Female NPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 4,000 psi (276 bar) output pressure is 143 psi (9.9 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Max Air Consumption @ 90 psi: 69 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 38 lbs. (17.2 kg) • Net Weight with Isolation Chamber: 50 lbs. (22.7 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Flow, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL25-01Single-Acting, Single Piston Air Drive Pump Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Flow, High Pressure Liquid Pump - Series ASL25-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL25-01SNPVASL = • Standard Liquid High Flow, High Pressure Pump • 6" Single Piston Air Drive • 1:28 Air-to-Liquid Pressure Ratio • Maximum 4,000 psi (276 bar)ASL25-01 SLiquid Inlet LocationNIsolationChamberPump Type / Size / RatioASL25-01 Series* N = None C = Included* S = Side B = BottomPVLiquid SealMaterials†* PV = UHMWPE U-Cup and Viton O-Rings PE = UHMWPE U-Cup and EPDM O-Rings PB = UHMWPE U-Cup and Buna-N O-Rings PC = UHMWPE U-Cup and Perfluoroelastomer O-Rings UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings*Standard for Stock Pumps† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" seal options. UHMWPE u-cup seals comes with a stainless steel spring energizerTechnical Specifications & Performance DataAir-Driven, High Flow, High Pressure Liquid Pump - Series ASL25-01Dimensional Data: Left View Front ViewRight ViewNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)Right View with Optional Isolation Chamber7.84(199.2)1/2” FNPTAir Drive Inlet0.47(11.9)See Note0.99(25.2)See Note11.54(293.12)Bottom Inlet9.83(249.7)Side Inlet6.87(174.5)Bracket SlotSpacing8.25(209.6)7.50(190.5)6.38(162.1)3.12(79.2)Slot SpacingBoth BracketsSee NoteLiquid OutletFemale 1/2” NPT3.27(83.0)6.92(175.67)Liquid InletFemale 1/2” NPT1/8” FNPT ExternalPilot Connection10.60(269.2)5.03(127.9)1.19(30.2)Pilot Valve Vent3.41(86.7)7.84(199.2)1/2” FNPTAir Drive Inlet0.47(11.9)See Note0.99(25.2)15.49(393.45)Bottom Inlet13.78(350.01)Side Inlet12.20(309.88)1/8”NFPTDrainPortIsolationChamberTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibilty • Maximum Outlet Pressure: 8,100 psi (558 bar) • Air to Liquid Pressure Ratio: 1:56 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 2.10 in3 (34.4 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 8,100 psi (558 bar) output pressure is 145 psi (10.0 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 61 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 47 lbs. (21.3 kg) • Net Weight with Isolation Chamber: 59 lbs. (26.8 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL25-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL25-02Flow Rate vs. Outlet Pressure: ASL25-02 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL25-02SNPVASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:56 Air-to-Liquid Pressure Ratio • Maximum 8,100 psi (558 bar)ASL25-02 SLiquid Inlet LocationNIsolationChamberPVLiquid SealMaterials†Pump Type / Size / Ratio* N = None C = Included* S = Side B = Bottom* PV = UHMWPE U-Cup and Viton O-Rings PE = UHMWPE U-Cup and EPDM O-Rings PB = UHMWPE U-Cup and Buna-N O-Rings PC = UHMWPE U-Cup and Perfluoroelastomer O-Rings UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings*Standard for Stock Pumps† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" seal options. UHMWPE u-cup seals comes with a stainless steel spring energizer0.99 (25.20)Technical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL25-02Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets12.19 (309.63)15.48(393.19)BottomInlet3.27 (83.0)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletFemale 1/2" NPT1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)10.81 (274.60)Bracket SlotSpacingNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)13.77 (349.76)SideInlet.47(11.94)1/8" FNPTDrain PortIsolationChamber15.58(395.73)BottomInlet13.78(350.01)SideInlet12.20(309.88)0.47 (11.94)6.92 (175.67)Side inletTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 5,600 psi (386 bar) • Air to Liquid Pressure Ratio: 1:39 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 1.50 in3 (24.6 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 5,600 psi (386 bar) output pressure is 144 psi (9.9 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Max Air Consumption @ 90 psi: 63 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 38 lbs. (17.2 kg) • Net Weight with Isolation Chamber: 50 lbs. (22.7 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Flow, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL35-01Single-Acting, Single Piston Air Drive Pump Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Flow, High Pressure Liquid Pump - Series ASL35-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL35-01SNPVASL = • Standard Liquid High Flow, High Pressure Pump • 6" Single Piston Air Drive • 1:39 Air-to-Liquid Pressure Ratio • Maximum 5,600 psi (386 bar)ASL35-01 SLiquid Inlet LocationNIsolationChamberPump Type / Size / Ratio* N = None C = Included* S = Side B = BottomASL35-01 SeriesPVLiquid SealMaterials†* PV = UHMWPE U-Cup and Viton O-Rings PE = UHMWPE U-Cup and EPDM O-Rings PB = UHMWPE U-Cup and Buna-N O-Rings PC = UHMWPE U-Cup and Perfluoroelastomer O-Rings UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings*Standard for Stock Pumps† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" seal options. UHMWPE u-cup seals comes with a stainless steel spring energizerTechnical Specifications & Performance DataAir-Driven, High Flow, High Pressure Liquid Pump - Series ASL35-01Dimensional Data: Left View Front ViewRight ViewNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)Right View with Optional Isolation Chamber7.84(199.2)1/2” FNPTAir Drive Inlet0.47(11.9)See Note0.99(25.2)See Note11.54(293.12)Bottom Inlet9.83(249.7)Side Inlet6.87(174.5)Bracket SlotSpacing8.25(209.6)7.50(190.5)6.38(162.1)3.12(79.2)Slot SpacingBoth BracketsSee NoteLiquid OutletFemale 1/2” NPT3.27(83.0)6.92(175.67)Liquid InletFemale 1/2” NPT1/8” FNPT ExternalPilot Connection10.60(269.2)5.03(127.9)1.19(30.2)Pilot Valve Vent3.41(86.7)7.84(199.2)1/2” FNPTAir Drive Inlet0.47(11.9)See Note0.99(25.2)15.49(393.45)Bottom Inlet13.78(350.01)Side Inlet12.20(309.88)1/8”NFPTDrainPortIsolationChamberTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibilty • Maximum Outlet Pressure: 11,200 psi (772 bar) • Air to Liquid Pressure Ratio: 1:78 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 1.50 in3 (24.6 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 11,200 psi (772 bar) output pressure is 143 psi (9.9 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 56 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 46 lbs. (20.9 kg) • Net Weight with Isolation Chamber: 58 lbs. (26.3 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL35-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL35-02Flow Rate vs. Outlet Pressure: ASL35-02 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL35-02SNPVASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:78 Air-to-Liquid Pressure Ratio • Maximum 11,200 psi (772 bar)ASL35-02 SLiquid Inlet LocationNIsolationChamberPVLiquid SealMaterials†Pump Type / Size / Ratio* N = None C = Included* S = Side B = Bottom* PV = UHMWPE U-Cup and Viton O-Rings PE = UHMWPE U-Cup and EPDM O-Rings PB = UHMWPE U-Cup and Buna-N O-Rings PC = UHMWPE U-Cup and Perfluoroelastomer O-Rings UV = Urethane U-Cup and Viton O-Rings UE = Urethane U-Cup and EPDM O-Rings UB = Urethane U-Cup and Buna-N O-Rings*Standard for Stock Pumps† 2nd character represents o-ring material in the check valves and the u-cup o-ring energizer material in the "U" seal options. UHMWPE u-cup seals comes with a stainless steel spring energizerTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL35-02Dimensional Data: Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)0.99 (25.20)Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets12.19 (309.63)15.84(402.34)BottomInlet3.49 (88.65)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletFemale 1/2" NPT1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)10.81 (274.60)Bracket SlotSpacing13.77 (349.76)SideInlet.47(11.94)1/8" FNPTDrain PortIsolationChamber19.78(502.41)BottomInlet17.72(450.09)SideInlet16.14(409.96)0.47 (11.94)7.06 (179.32)Side inletTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 10,000 psi (690 bar) • Air to Liquid Pressure Ratio: 1:70 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.84 in3 (13.7 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 10,000 psi (690 bar) output pressure is 143 psi (9.9 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Max Air Consumption @ 90 psi: 64 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 32 lbs. (14.5 kg) • Net Weight with Isolation Chamber: 41 lbs. (18.6 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL60-01Single-Acting, Single Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL60-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL60-01SNPASL = • Standard Liquid High Pressure Pump • 6" Single Piston Air Drive • 1:70 Air to Liquid Pressure Ratio • Maximum 10,000 psi (690 bar)ASL60-01 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialsPump Type / Size / RatioASL60-01 Series* S = Side B = Bottom*Standard for Stock Pumps* N = None C = Included* P = UHMWPE U-Cup with Elgiloy Spring EnergizerUV = Urethane U-Cup with Viton O-Ring EnergizerUE = Urethane U-Cup with EPDM O-Ring EnergizerUB = Urethane U-Cup with Buna-N O-Ring Energizer Technical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL60-01Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)Pilot Valve VentSlot SpacingBoth BracketsSee NoteLiquid Inlet Female 1/2" NPTLiquid OutletFemale 1/2" NPT1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters).47(11.94)1/8" FNPTDrain PortIsolationChamber16.05(407.7)BottomInlet13.20(335.28)SideInlet12.26(311.40)0.47 (11.94)8.31 (211.07)0.99 (25.20)6.87 (174.55)Bracket SlotSpacing7.50 (190.50)6.38 (162.05)3.12 (79.25)3.43(87.12)7.24(183.90)1/8" FNPT External Pilot Connection12.10 (307.34)BottomInlet9.25 (234.95)SideInletTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibilty • Maximum Outlet Pressure: 20,000 psi (1,379 bar) • Air to Liquid Pressure Ratio: 1:140 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.84 in3 (13.8 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: Autoclave SF562CX20-9/16" Female Medium Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 20,000 psi (1,379 bar) output pressure is 143 psi (9.9 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 59 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 43 lbs. (19.5 kg) • Net Weight with Isolation Chamber: 53 lbs. (24.0 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL60-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL60-02Flow Rate vs. Outlet Pressure: ASL60-02 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL60-02SNPASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:140 Air-to-Liquid Pressure Ratio • Maximum 20,000 psi (1,379 bar)ASL60-02 SLiquid Inlet LocationNIsolationChamberPSealMaterialPump Type / Size / Ratio* N = None C = Included* S = Side B = Bottom* P = UHMWPE U-Cup with Elgiloy Spring EnergizerUV = Urethane U-Cup with Viton O-Ring EnergizerUE = Urethane U-Cup with EPDM O-Ring EnergizerUB = Urethane U-Cup with Buna-N O-Ring Energizer *Standard for Stock PumpsTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL60-02Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve VentSlot SpacingBoth Brackets12.25 (311.15)16.04(407.42)BottomInletSee NoteLiquid Inlet Female 1/2" NPTLiquid OutletAutoclave SF562CX-9/16"Female MediumPressure1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)0.99 (25.20)10.81 (274.60)Bracket SlotSpacingNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)13.19 (335.03)SideInlet.47(11.94)1/8" FNPTDrain PortIsolationChamber17.13(435.10)SideInlet16.20(411.48)0.47 (11.94)7.50 (190.50)6.38 (162.05)3.12 (79.25)7.24 (183.90)Side inlet3.43 (87.12)19.99(507.75)Bottom InletTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 15,000 psi (1034 bar) • Air to Liquid Pressure Ratio: 1:113 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.52 in3 (8.5 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: 1/2" FNPT (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 15,000 psi (1034 bar) output pressure is 133 psi (9.2 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Max Air Consumption @ 90 psi: 64 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 32 lbs. (14.5 kg) • Net Weight with Isolation Chamber: 41 lbs. (18.6 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL100-01Single-Acting, Single Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL100-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL100-01SNPASL = • Standard Liquid High Pressure Pump • 6" Single Piston Air Drive • 1:113 Air-to-Liquid Pressure Ratio • Maximum 15,000 psi (1034 bar)ASL100-01 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialPump Type / Size / RatioASL100-01 Series* S = Side B = Bottom* P = UHMWPE U-Cup with Stainless Steel Spring Engergizer U = Urethane U-Cup*Standard for Stock Pumps* N = None C = Included1/8" FNPT External Pilot ConnectionTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL100-01Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)Pilot Valve VentSlot SpacingBoth BracketsSee NoteLiquid Inlet Female 1/2" NPTLiquid OutletFemale 1/2" NPT1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters).47(11.94)1/8" FNPTDrain PortIsolationChamber16.05(407.67)BottomInlet13.20(335.28)SideInlet12.26(311.40)0.47 (11.94)8.31 (211.07)0.99 (25.20)6.87 (174.55)Bracket SlotSpacing9.25 (234.95)SideInlet7.50 (190.50)6.38 (162.05)3.12 (79.25)3.43(87.12)7.24(183.90)12.10(307.34)BottomInletTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibilty • Maximum Outlet Pressure: 31,000 psi (2,137 bar) • Air to Liquid Pressure Ratio: 1:226 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.52 in3 (8.5 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 31,000 psi (2,137 bar) output pressure is 137 psi (9.5 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 59 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 42 lbs. (19.1 kg) • Net Weight with Isolation Chamber: 51 lbs. (23.1 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL100-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL100-02Flow Rate vs. Outlet Pressure: ASL100-02 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL100-02SNPASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:226 Air-to-Liquid Pressure Ratio • Maximum 31,000 psi (2,137 bar)ASL100-02 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialPump Type / Size / Ratio* N = None C = Included* S = Side B = Bottom*Standard for Stock Pumps* P = UHMWPE U-Cup with Stainless Steel Spring Energizer U = Urethane U-CupTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL100-02Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets12.25 (311.15)15.50(393.73)BottomInlet4.18 (106.17)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletAutoclave EngineersF250C - 1/4" Female High Pressure Connection1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)0.99 (25.20)10.81 (274.60)Bracket SlotSpacingNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)7.45 (189.23)Side inlet13.19 (335.03)SideInlet.47(11.94)1/8" FNPTDrain PortIsolationChamber19.45(494.03)BottomInlet17.13(435.10)SideInlet16.20(411.48)0.47 (11.94)Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 21,500 psi (1,482 bar) • Air to Liquid Pressure Ratio: 1:150 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.39 in3 (6.4 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 21,500 psi (1,482 bar) output pressure is 145 psi (10 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 69 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 32 lbs. (14.5 kg) • Net Weight with Isolation Chamber: 41 lbs. (18.6 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL150-01Single-Acting, Single Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL150-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL150-01SNPASL = • Standard Liquid High Pressure Pump • 6" Single Piston Air Drive • 1:150 Air-to-Liquid Pressure Ratio • Maximum 21,500 psi (1,482 bar)ASL150-01 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialPump Type / Size / RatioASL150-01 Series* S = Side B = Bottom*Standard for Stock Pumps* N = None C = Included* P = UHMWPE U-Cup with Elgiloy Spring Engergizer U = Urethane U-Cup1/8" FNPT External Pilot ConnectionTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL150-01Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)Pilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets4.18(106.17)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletAutoclave EngineersF250C - 1/4" Female High Pressure Connection1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)7.45(189.23).47(11.94)1/8" FNPTDrain PortIsolationChamber15.50(393.70)BottomInlet13.20(335.28)SideInlet12.26(311.40)0.47 (11.94)8.31 (211.07)11.55(293.37)BottomInlet0.99 (25.20)6.87 (174.55)Bracket SlotSpacing9.25 (234.95)SideInletTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility. • Maximum Outlet Pressure: 43,000 psi (2,965 bar) • Air to Liquid Pressure Ratio: 1:300 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.39 in3 (6.4 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 43,000 psi (2,965 bar) output pressure is 143 psi (9.9 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 64 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 42 lbs. (19.1 kg) • Net Weight with Isolation Chamber: 51 lbs. (23.1 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL150-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL150-02Flow Rate vs. Outlet Pressure: ASL150-02 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL150-02SNPASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:300 Air-to-Liquid Pressure Ratio • Maximum 43,000 psi (2,965 bar)ASL150-02 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialPump Type / Size / Ratio* N = None C = Included* S = Side B = Bottom* P = UHMWPE U-Cup with Elgiloy Spring Energizer U = Urethane U-Cup*Standard for Stock PumpsTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL150-02Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets12.25 (311.15)15.50(393.73)BottomInlet4.18 (106.17)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletAutoclave EngineersF250C - 1/4" Female High Pressure Connection1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)0.99 (25.20)10.81 (274.60)Bracket SlotSpacingNote: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)7.45 (189.23)Side inlet13.19 (335.03)SideInlet.47(11.94)1/8" FNPTDrain PortIsolationChamber19.45(494.03)BottomInlet17.13(435.10)SideInlet16.20(411.48)0.47 (11.94)Technical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 38,400 psi (2,648 bar) • Air to Liquid Pressure Ratio: 1:265 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.22 in3 (3.6 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 38,400 psi (2,648 bar) output pressure is 145 psi (10 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 69 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 32 lbs. (14.5 kg) • Net Weight with Isolation Chamber: 41 lbs. (18.6 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 316 Stainless Steel • Liquid Seal: See Ordering Guide for options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL250-01Single-Acting, Single Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL250-01Flow Rate vs. Outlet Pressure: Actual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL250-01SNPASL = • Standard Liquid High Pressure Pump • 6" Single Piston Air Drive • 1:265 Air-to-Liquid Pressure Ratio • Maximum 38,400 psi (2,648 bar)ASL250-01 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialPump Type / Size / Ratio01002003004005006007008000 500 1000 1500 2000051015202530354045500 5000 10000 15000 20000 25000 30000FLOW RATE (IN3 /MIN)OUTLET PRESSURE (PSI)CHARTED FLOW RATES ARE FOR 1-10 CST FLUIDSOUTLET PRESSURE (BAR)FLOWRATE (CM3/MIN)120 PSI[8 BAR]90 PSI[6 BAR]60 PSI[4 BAR]AIR DRIVE PRESSURE60 PSI      90 PSI     120 PSI[4 BAR]   [6 BAR]   [8 BAR]ASL250-01 Series* N = None C = Included* S = Side B = Bottom* P = UHMWPE U-Cup with Elgiloy Spring Energizer U = Urethane U-Cup*Standard for Stock PumpsTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL250-01Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets4.18(106.17)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletAutoclave EngineersF250C - 1/4" Female High Pressure Connection1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)7.45(189.23).47(11.94)1/8" FNPTDrain PortIsolationChamber15.50(393.70)BottomInlet13.20(335.28)SideInlet12.26(311.40)0.47 (11.94)8.31 (211.07)11.55(293.37)BottomInlet0.99 (25.20)6.87 (174.55)Bracket SlotSpacing9.25 (234.95)SideInletTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 60,000 psi (4,137 bar) • Air to Liquid Pressure Ratio: 1:530 • Isolation Chamber (prevents process contamination of air section): Standard • Volume Displacement Per Stroke: 0.22 in3 (3.6 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 60,000 psi (4,137 bar) output pressure is 113 psi (7.8 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 64 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight with Isolation Chamber: 54 lbs. (24.5 kg) • Pressure Head: 15-5 PH Stainless Steel • Plunger: Tungsten Cobalt • Check Valve Glands: 15-5 PH Stainless Steel • Liquid Seal: See Ordering Guide for options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL250-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL250-02Flow Rate vs. Outlet Pressure: ASL250-02 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL250-02SCPASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:530 Air-to-Liquid Pressure Ratio • Maximum 60,000 psi (4,137 bar)C = IncludedASL250-02 SLiquid Inlet LocationCIsolationChamberPLiquid SealMaterialPump Type / Size / Ratio* S = Side B = Bottom*Standard for Stock Pumps* P = UHMWPE U-Cup with Elgiloy Spring Energizer U = Urethane U-Cup7.50 (190.50)Technical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL250-02Dimensional Data: Left View Front View5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets19.63(498.55)BottomInlet2.75 (69.85)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletAutoclave EngineersF250C - 1/4" Female High Pressure Connection10.60 (269.16)3.41 (86.71)Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)6.13 (155.69)Side inletRight View1/2" FNPT Air Drive InletSee NoteSee Note7.84 (199.18)0.99 (25.20)0.47 (11.94)1/8" FNPTDrain PortIsolationChamber17.27 (438.73)SideInlet16.25 (412.83)10.81 (274.60)Bracket SlotSpacingTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 57,700 psi (3,978 bar) • Air to Liquid Pressure Ratio: 1:398 • Isolation Chamber (prevents process contamination of air section): Optional • Volume Displacement Per Stroke: 0.14 in3 (2.3 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 57,700 psi (3,978 bar) output pressure is 145 psi (10 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 90 psi: 70 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight without Isolation Chamber: 32 lbs. (14.5 kg) • Net Weight with Isolation Chamber: 41 lbs. (18.6 kg) • Pressure Head: 15-5 PH Stainless Steel • Stainless steel plunger utilizing a proprietary multi-layer carbon based coating with diamond like carbon exterior layer - 3 times the hardness of stellite with a coefficient of friction equal to/less than PTFE • Check Valve Glands: 15-5 PH Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Single Piston Air Drive Series ASL400-01Single-Acting, Single Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL400-01Flow Rate vs. Outlet Pressure: ASL400-01 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL400-01SNPASL = • Standard Liquid High Pressure Pump • 6" Single Piston Air Drive • 1:398 Air-to-Liquid Pressure Ratio • Maximum 57,700 psi (3,978 bar)ASL400-01 SLiquid Inlet LocationNIsolationChamberPLiquid SealMaterialPump Type / Size / Ratio* N = None C = Included* S = Side B = Bottom*Standard for Stock Pumps* P = UHMWPE U-Cup with Elgiloy Spring Energizer U = Urethane U-CupTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL400-01Dimensional Data: Left View Front ViewRight ViewRight View with Optional Isolation Chamber5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets2.75 (69.84)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletAutoclave EngineersF250C - 1/4" Female High Pressure Connection1/2" FNPT Air Drive Inlet10.60 (269.16)See NoteSee Note7.84 (199.18)3.41 (86.71)Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)6.13 (155.69)Side inlet.47(11.94)1/8" FNPTDrain PortIsolationChamber15.68(398.27)BottomInlet13.33(338.58)SideInlet12.31(312.67)0.47 (11.94)8.37 (212.55)11.74(298.26)BottomInlet0.99 (25.20)6.87 (174.55)Bracket SlotSpacing9.39 (238.51)SideInletTechnical Data: Liquid Side Specifications • Service: Oil, Water or Water/Oil mixture and other fluids depending on material compatibility • Maximum Outlet Pressure: 60,000 psi (4,137 bar) • Air to Liquid Pressure Ratio: 1:796 • Isolation Chamber (prevents process contamination of air section): Standard • Volume Displacement Per Stroke: 0.14 in3 (2.3 cm3) • Inlet Connection: 1/2" FNPT • Outlet Connection: Autoclave F250C-1/4" Female High Pressure (Contact Autoclave Engineers for Additional Options)Technical Data: Air Side Specifications • Air Drive Pressure Range: 15-150 psi (1-10 bar) *See note1 • Nominal air pressure required for 60,000 psi (4,137 bar) output pressure is 75 psi (5.2 bar) • Inlet Port: 1/2" FNPT • Pilot Port: 1/8" FNPT (unregulated air) • Exhaust Port (muffler removed): 1/2" FNPT • Air Consumption @ 75 psi: 48 SCFM • Prelubricated at FactoryGeneral Specifications • Maximum Operating Temperature: 0-140º F (-18º to 60º C) • Net Weight with Isolation Chamber: 54 lbs. (24.5 kg) • Pressure Head: 15-5 PH Stainless Steel • Plunger: Tungsten Cobalt • Check Valve Glands: 15-5 PH Stainless Steel • Liquid Seal: See Ordering Guide for Options • Air Drive Seals: Buna N Notes: 1. Maximum air drive pressure is limited by maximum output pressure. 2. Alternative materials for wetted parts and seals are available, please contact Autoclave Engineers for additional information.www.autoclave.comAir-Driven, High Pressure Liquid PumpSingle-Acting, Dual Piston Air Drive Series ASL400-02Single-Acting, Dual Piston Air Drive Bottom Inlet ShownMADE IN THE U.S.A.Technical Specifications & Performance Data Air- Driven, High Pressure Liquid Pump - Series ASL400-02Flow Rate vs. Outlet Pressure: ASL400-02 SeriesActual flow rates will vary depending on air flow capacity, downstream flow restrictions, and fluid type.Ordering Guide: For complete information on available pump options, contact Autoclave Engineers. Typical catalog number: ASL400-02SCPASL = • Standard Liquid High Pressure Pump • 6" Dual Piston Air Drive • 1:796 Air-to-Liquid Pressure Ratio • Maximum 60,000 psi (4,137 bar)ASL400-02 SLiquid Inlet LocationCIsolationChamberPLiquid SealMaterialPump Type / Size / Ratio C = Included* S = Side B = Bottom*Standard for Stock Pumps* P = UHMWPE U-Cup with Elgiloy Spring Energizer U = Urethane U-CupTechnical Specifications & Performance DataAir-Driven, High Pressure Liquid Pump - Series ASL400-02Dimensional Data: Left View Front View5.03 (127.86)1.19 (30.23)1/8" FNPT External Pilot ConnectionPilot Valve Vent7.50 (190.50)6.38 (162.05)3.12 (79.25)Slot SpacingBoth Brackets19.63(498.55)BottomInlet2.75 (69.85)See NoteLiquid Inlet Female 1/2" NPTLiquid OutletAutoclave EngineersF250C - 1/4" Female High Pressure Connection10.60 (269.16)3.41 (86.71)Note: Each Mounting Bracket includes (2) x 13/32" (10.32) Slots for 3/8" Bolts. Bottom Inlet Pump Head and Side Inlet Pump Head are mutually exclusive. All dimensions are for reference only and are subject to change without notice. Primary Dimensions: Inches Secondary Dimensions: (Millimeters)6.13 (155.69)Side inletRight View1/2" FNPT Air Drive InletSee NoteSee Note7.84 (199.18)0.99 (25.20)0.47 (11.94)1/8" FNPTDrain PortIsolationChamber17.27 (438.73)SideInlet16.25 (412.83)10.81 (274.60)Bracket SlotSpacing02-9232BE-1010 WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE.This document and other information from Snap-tite, Inc., its subsidiaries and authorized distributors, provides product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operation conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met.The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Snap-tite, Inc. and its subsidiaries at any time without notice.All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.Industrial EstateWhitemill-WexfordRepublic of IrelandPH: 353 53 914 1566 FAX: 353 53 914 1582e-mail: ste_sales@snap-tite.comwww.snap-tite.com8325 Hessinger DriveErie, Pennsylvania 16509-4679 USAPH: 814-860-5700 FAX: 814-860-5811e-mail: ae_sales@snap-tite.comwww.autoclave.comISO-9001 CertifiedAccessories Available: • Air Control Packages • Pneumatic Pilot switches and Solenoid Valves • Stroke Counter • Relief Valve / Safety Heads • Complete line of High Pressure Components - Valves, Fittings & Tubing • Spare Parts • ServiceAir-Driven, High Pressure Liquid Pump - Series ASL400-02For complete information on available high pressure accessories, please contact Autoclave Engineers. Typical Air Control Package