Butterfly Valve Products Catalog

11.1? CHEVRON V-TYPE PACKING - is self-adjusting, long lasting and should never need replacement because quarter-turn valve operation causes little or no wear. Packing bears on turned, ground and polished stainless steel.? CORROSION RESISTANT SHAFT - is constucted of stainless steel. Shaft is one-piece, through-shaft construction sized to meet or exceed requirements of AWWA Standard C504 for Class 150B or Class 250B service. ? HEAVY DUTY BODY - is extra heavy with flanges fully faced and drilled per ANSI B16.1 Class 125 standard**. Other ends available include integrally cast mechanical joint and slip-on (for DI and PVC C900). Operator mounting trunnion is machined and drilled for four-bolt connection. ? TAMPER-PROOF DISC CENTERING - provided by precision molded flats in the bonded seat at the body trunnion mate with machined flats on the disc to provide tamperproof centering of the disc in the body. Positive disc alignment, without play, assures long seat life. MUELLER® LINESEAL III®, LINESEAL XP™, LINESEAL XPII™ BUTTERFLY VALVES 3"-20" DESIGN*MUELLER LINESEAL III (Class 150B), LINESEAL XP*, LINESEAL XPII (Class 250B) Butterfly Valve Features *Lineseal XP Valves 3" and 4" only.**Lineseal XP Valve flanges drilled to ANSI B16.1 Class 250 standard. ? SELF-LUBRICATING BEARINGS - are liberally sized, chemically inert bearings that are self-lubricating and should outlast the life of the pipeline.? STREAMLINED DISC - has lens-shaped design to minimize pressure drop and turbulence. Full open valve creates no more friction loss than a 45° elbow. Disc is secured to the shaft by stainless steel pins sized to transmit torques required and withstand stresses imposed under severe operating conditions. Disc has stainless steel disc edge. ? ELASTOMERIC BODY SEAT - is made of a special rubber compound (Buna N) that is bonded to the body by a patented process. The seat cannot be torn from the body under normal pipeline conditions. The precision molding process also ensures that the disc-seat indentation cannot cause excessive wear or abrasion upon closing. Shaded area indicates change Rev. 9-0911.2MUELLER LINESEAL III (Class 150B), LINESEAL XP, LINESEAL XP II (Class 250B) Butterfly Valve FeaturesMUELLER® LINESEAL III®, LINESEAL XP™, LINESEAL XPII™ BUTTERFLY VALVES 24"-48"* DESIGN * Contact your Mueller representative for valves sizes larger than 48"and for Lineseal XP Valves with Class 250 flanges, this page applies to 24"-48" sizes. ? CORROSION RESISTANT SHAFT - is constucted of stainless steel. Two-piece, stub-type shafts are sized per AWWA Standard C504, Class 150B or Class 250.? CHEVRON V-TYPE PACKING - is self-adjusting packing in top trunnion of valve body where shaft protrudes.? STRONG DISC AND SHAFT CONNECTIONS - with generously sized stainless steel pins designed to transmit torques required and withstand stresses imposed under severe operating conditions. ? PRESET TWO-WAY THRUST BEARING ASSEMBLY - is preset at factory. On valves 30" and larger, assembly consists of stainless steel stud fastened to the bottom of the valve shaft. Stud extends beyond the bottom cover. Thrust collar is threaded to the stud and pinned. On 24" valves thrust collar is pinned to shaft and adjustment provided by bronze spacers. Thrust collar cavity is packed with grease and fully gasketed to prevent leakage. ? HEAVY DUTY BODY - is extra heavy with flanges fully faced and drilled per ANSI B16.1 Class 250 or Mechanical Joint ends are also available. ? SELF-LUBRICATING, SLEEVE-TYPE BEARINGS - are used in both trunnions of the valve body. PTFE lined with special non-metallic backing. Provide electrical insulation between disc and shaft to prevent galvanic corrosion. Lower coefficient of friction reduces operating torque requirements. ? FLOW-THROUGH DISC* - provides less pressure drop in full-open position than conventional disc shapes. (On 24" size valves the arch side of disc is closed and the flat side is open, forming a slightly concave surface.) Disc structure has no internal cores that can shift during casting, no hollow chambers that can collect water, freeze and fracture the disc. Disc edge has stainless steel spherically shaped seating surface.? ELASTOMERIC SEAT - is made of a special rubber compound (Buna N) that seals a full 360 against a stainless steel spherical disc edge. Unique grooved-seal design, coupled with the wide spherically shaped seating edge of the disc, allows greater disc closure tolerance (up to 1° off center in closed position without leakage). Seat is mechanically retained in body without metal hardware by a cast epoxy compound that ensures the seat conforms to the exact radius of the disc with uniform contact pressure. It is fully field adjustable and replaceable.Rev. 9-09 Shaded area indicates changes11.3? Hand lever for 3"-10" valves? 200 psi test? EPDM Rubber seat and seals? 316 Stainless steel fasteners? Catalog number-- 3211-6 Flanged Ends Class 125 Sizes--3", 4", 6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36", 42", 48" 3211-20 Mechanical joint ends (with mechanical joint unassembled accessories) Sizes--4", 6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36", 42", 48" 3211-23 Mechanical joint ends (without mechanical joint accessories) Sizes--4", 6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36", 42", 48" 3211-16 Flanged Class 125 by mechanical joint ends (with mechanical joint unassembled accessories) Sizes--6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36 3211-19 Flanged Class 125 by mechanical joint ends (without mechanical joint unassembled accessories) Sizes--6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36 ? Meets or exceeds all applicable requirements of ANSI/AWWA C504 Standard Class 150B; NSF 61 certified ? Buried service valves: I.D. and O.D. coated? Body - Cast Iron ASTM A-126? Flanges drilled per ANSI B16.1 Class 125? Above ground valves (ordered with either a handwheel, position indicator on the actuator, or lever): minimum 8 mills epoxy coated interior and exterior; meets AWWA C504 standard. ? Seat-in-body design reduces seat failure due to corrosive buildup in the valve and pipeline ? Through-disc pinning provides a tight disc-to-shaft pin connection, greatly reducing the possibility of loosening through vibration ? Disc edge is 316 Stainless Steel ? Disc - Cast Iron ASTM A-126 (3", 4", 6" Stainless Steel ASTM A-743 CF8M)? Symmetrical disc for higher Cv and lower head loss ? Nonmetallic bearings prevent galvanic corrosion and provides lower coefficient of friction ? Cheveron "V" type packing is self-adjusting to last the life of the valve ? 3"-24" Standard 304 SS hardware. Options *Contact your Mueller representative for valve sizes larger than 48". Standard Buried Service ActuatorsNote: Actuator size subject to change based on actual pipeline conditions. MUELLER® LINESEAL III® BUTTERFLY VALVES (Class 150B) 3" - 48"* ? MDT Actuator with handwheel or chainwheel and position indicator? MDT Actuator with cylinder actuator (also available with manual override, handjack and 4-way solenoid valve)? Additional mils available Epoxy interior and/or exterior? Holiday testing? Ground level position indicatorSlotted-Lever (3"-12")3"-20"24"-48"Valve size Actuator Number of turns3"-12" MDT-2S 3214"-16" MDT-3S 3018"-24" MDT-4S 4030"-36" MDT-5 4442" MDT-5S 13648" MDT-6S 215Shaded area indicates change Rev. 9-0911.4 MUELLER® LINESEAL III® BUTTERFLY VALVES-(CLASS 150B) 3"-48"*-FLANGED ENDSDimensions - for Lineseal III Valves Flanged (Class 125) Ends, 3"-20" Sizes.Dimensions - for Lineseal III Valves Flanged (Class 125) Ends, 24"-48" Sizes.* Larger sizes available upon request. + All dimensions are in inches. † -+1/16" for 10" valves, and -+1/8" for 12"-48" valves per Flange Standard ANSI B16.1.Notes: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings available upon request. Actuator size subject to change based on actual pipeline conditions.Dimension+Nominal size*3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36" 42" 48"A 4.75 5.50 6.50 7.75 9.00 10.5 11.88 13.50 14.38 16.00 18.63 21.50 25.44 29.88 34.06B 3.88 4.13 5.13 6.50 9.88 11.38 12.63 14.50 15.38 17.00 18.63 24.38 28.25 32.88 37.13C 7.50 9.00 11.00 13.50 16.00 19.00 21.00 23.50 25.00 27.50 32.00 38.75 46.00 53.00 59.50D† 5.00 5.00 5.00 6.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 12.00 12.00 12.00 15.00E .75 .94 1.00 1.13 1.19 1.25 1.38 1.44 1.56 1.69 1.88 2.13 2.38 2.63 2.75F (number and size of holes) 4--.63 8--.63 8--.75 8--.75 12--.88 12--.88 12--1 16--1 16--1.13 20--1.13 20--1.25 28--1.25 32--1.50 36--1.50 44--1.50G 6.00 7.50 9.50 11.75 14.25 17.00 18.75 21.25 22.75 25.00 29.50 36.00 42.75 49.50 56.00J 4.69 4.69 4.69 4.69 4.69 4.69 5.63 5.63 6.38 6.38 6.38 7.56 7.56 8.31 9.88L 2.00 2.00 2.00 2.00 2.00 2.00 2.44 2.44 2.84 2.84 2.84 3.47 3.47 3.94 5.06Q 4.50 4.50 4.50 4.50 4.50 4.50 5.38 5.38 6.75 6.75 6.75 10.00 10.00 15.94 14.19R 8.25 8.25 8.25 8.25 8.25 8.25 10.38 10.38 11.31 11.31 11.31 17.00 17.00 19.88 26.50Turns to open 32 32 32 32 32 32 30 30 40 40 40 44 44 136 215Actuator (see notes) MDT-2S MDT-2S MDT-2S MDT-2S MDT-2S MDT-2S MDT-3S MDT-3S MDT-4S MDT-4S MDT-4S MDT-5 MDT-5 MDT-5S MDT-6SRev. 9-09 Shaded area indicates changes11.5MUELLER® LINESEAL III® BUTTERFLY VALVES CLASS 150B 6"-20" - M.J. X FL.Dimensions - for Lineseal III Valves Mechanical Joint by Flange (Class 125) Ends, 6"-20" Sizes.+ All dimensions are in inches. When using 10" and 12" Valves on Class 200 PVC Pipe, pipe end I.D.must be bevelled to ensure clearance for disc and proper valve operation. Contact your Mueller Sales Representative for detailed instructions.CAUTIONNotes: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings available upon request. Actuator size subject to change based on actual pipeline conditions.Dimension+Nominal size6" 8" 10" 12" 14" 16" 18" 20"A 6.50 7.75 9.00 10.50 11.88 13.50 14.38 16B 5.13 6.50 9.88 11.38 12.75 14.38 15.25 16.88C 11.00 13.50 16.00 19.00 21.00 23.50 25.00 27.50CC 11.00 13.25 15.56 17.94 20.31 22.56 24.69 27.09D† 6.75 7.31 8.62 8.63 9.75 10.00 10.13 10.25DD 4.25 4.31 4.62 4.63 5.75 6.00 6.13 6.25E 1.06 1.13 1.25 1.25 1.38 1.44 1.56 1.69EE 1.06 1.13 1.19 1.25 1.31 1.38 1.44 1.50F (number and size of holes) 8--.75 8--.75 12--.88 12--.88 12--1.00 16--1.00 16--1.13 20--1.13FF (number and size of holes) 6--.75 6--.75 8--.75 8--.75 10--.75 12--.75 12--.75 14.75G 9.50 11.75 14.25 17.00 18.75 21.25 22.75 25.00GG 9.50 11.75 14.00 16.25 18.75 21.00 23.25 25.50J 4.69 4.69 4.69 4.69 5.63 5.63 6.38 6.38L 2.00 2.00 2.00 2.00 2.44 2.44 2.84 2.84Q 4.50 4.50 4.50 4.50 5.38 5.38 6.75 6.75R 8.75 8.25 8.25 8.25 10.38 10.38 11.31 11.31X 4.25 4.81 6.13 6.13 6.25 6.50 6.63 6.75Turns to open 32 32 32 32 30 30 40 40Actuator (see notes) MDT-2S MDT-2S MDT-2S MDT-2S MDT-3S MDT-3S MDT-4S MDT-4SShaded area indicates change Rev. 9-0911.6 MUELLER® LINESEAL III® BUTTERFLY VALVES CLASS 150B 4"-48" - M.J. ENDSDimensions - for Lineseal III Valves M.J. Ends, 4"-20" Sizes.Dimensions - for Mueller Lineseal III Butterfly Valves M.J. Ends, 24"-48" Sizes. + All dimensions are in inches. When using 10" and 12" Valves on Class 200 PVC Pipe, pipe end I.D.must be bevelled to ensure clearance for disc and proper valve operation. Contact your Mueller Sales Representative for detailed instructions.CAUTIONNotes: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings available upon request. Actuator size subject to change based on actual pipeline conditions.Dimension+Nominal size4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36" 42" 48"A 5.50 6.50 7.75 9.00 10.50 11.88 13.50 14.38 16.00 18.63 21.50 25.44 29.88 34.06B 4.13 5.13 6.50 9.75 11.38 12.75 14.50 15.38 17.00 18.38 24.13 28.00 32.75 36.88C 9.00 11.00 13.25 15.56 17.94 20.31 22.56 24.69 27.09 31.56 39.00 45.88 53.00 59.88D 8.13 8.50 8.63 9.25 9.25 11.50 12.00 12.25 12.50 13.25 18.00 22.00 22.00 24.00E 1.00 1.06 1.13 1.19 1.25 1.31 1.38 1.38 1.50 1.63 1.81 2.00 2.00 2.00F (number and size of holes) 4--.75 6--.75 6--.75 8--.75 8--.875 10--.875 12--.875 12--.875 14--.875 16--.875 20--1.13 24--1.13 28--1.38 32--1.38G 7.50 9.50 11.75 14.00 16.25 18.75 21.00 23.25 25.25 30.00 36.88 43.75 50.63 57.50J 4.69 4.69 4.69 4.69 4.69 5.63 5.63 6.38 6.38 6.38 7.56 7.56 8.31 11.19L 2.00 2.00 2.00 2.00 2.00 2.44 2.44 2.84 2.84 2.84 3.47 3.47 3.94 5.06Q 4.50 4.50 4.50 4.50 4.50 5.44 5.44 6.75 6.75 6.75 10.13 10.13 15.94 18.56R 8.25 8.25 8.25 8.25 8.25 10.38 10.38 11.31 11.31 11.31 17.00 17.00 19.88 26.50X 3.12 3.50 3.63 4.25 4.25 4.50 5.00 5.25 5.50 6.38 10.00 14.00 14.00 16.00Turns to open 32 32 32 32 32 30 30 40 40 40 44 44 136 215Actuator (see notes) MDT-2S MDT-2S MDT-2S MDT-2S MDT-2S MDT-3S MDT-3S MDT-4S MDT-4S MDT-4S MDT-5 MDT-5 MDT-5S MDT-6SRev. 5-15 Shaded area indicates changes11.7MUELLER® LINESEAL III® BUTTERFLY VALVES CLASS 150B 12", 16" - SL. X FL.Dimensions - for Lineseal III Valves Slip-on by Flanged Ends (Class 125), 12", 16" Sizes.+ All dimensions are in inches. IMPORTANT:1. Slip On end of this valve NOT FOR USE with IPS O.D. Pipe. 2. Slip On end of this valve for use with Tyton™ Rubber Ring Gasket (Tyton is a registered Trade Mark of U.S. Pipe & Foundry Co.).When using 12" Valves on Class 200 PVC Pipe, pipe end I.D.must be bevelled to ensure clearance for disc and proper valve operation. Contact your Mueller Sales Representative for detailed instructions.CAUTIONNotes: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings available upon request. Actuator size subject to change based on actual pipeline conditions.Dimension+Nominal size12" 16"A 10.50 13.50B 11.38 13.88C (Slip on end) 16.38 21.25CC (Flanged end) 19.00 23.50D 11.50 11.50DD 4.00 4.00E 1.25 1.44F (number and size of holes) 12--.88 16--1.00G 17.00 21.25J 4.69 5.63L 2.00 2.44Q 4.50 5.38R 8.25 10.38X (Laying length) 6.56 9.19Turns to open 32 30Actuator (see notes) MDT-2S MDT-3SPipe sizePipe O.D.12" 16"13.20 17.40Shaded area indicates change Rev. 9-0911.8 MUELLER® LINESEAL III® BUTTERFLY VALVES CLASS 150B 12", 16" - SLIP-ON Dimensions - for Mueller Lineseal III Butterfly Valves Slip-on Ends, 12", 16" Sizes.+All dimensions are in inches. IMPORTANT:1. This valve NOT FOR USE with IPS O.D. Pipe.When using 12" Valves on Class 200 PVC Pipe, pipe end I.D.must be bevelled to ensure clearance for disc and proper valve operation. Contact your Mueller Sales Representative for detailed instructions.CAUTIONNotes: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings available upon request. Actuator size subject to change based on actual pipeline conditions.Dimension+Nominal size12" 16"A 10.50 13.50B 11.38 14.50C 16.38 21.25D 15.00 15.00J 4.69 5.63L 2.00 244Q 4.50 5.38R 8.25 10.38X (Laying length) 5.13 4.75Turns to open 32 30Actuator (see notes) MDT-2S MDT-3SPipe sizePipe O.D.12" 16"13.20 17.40Rev. 9-09 Shaded area indicates changes11.9MUELLER® LINESEAL III® BUTTERFLY VALVES CLASS 150B 3"-48"* PARTS* Contact you Mueller representative for sizes larger than 48".**3", 4", 6" is ASTM A-351 CF8M Stainless Steel. BF106 BF105 BF100 BF104 BF103 BF102 BF101 BF110 BF104 BF105 BF107 BF108 BF109 BF104BF11110" THRU 20" 3" AND 8" VALVESCatalog Part No. Description MaterialBF100 Body Cast iron ASTM A126 CL.BBF101 Disc** Cast iron ASTM A126, Class B with 316 EdgeBF102 Shaft Stainless Steel 18-8 Type 304 ASTM A-276BF103 Squeeze pin Stainless Steel 18-8 Type 304 ASTM A-276BF104 Bearing Nylatron GSBF105 Packing Chevron V-TypeBF106 Key Carbon Steel C-1045BF107 Cover Cast Iron ASTM A-48 Class 40BF108 Lockwasher Stainless Steel Type 304BF109 Cap Screw Stainless Steel Type 304BF110 Seat Buna NBF111 Plug Stainless Steel Type 304BF112 Bearings PTFE Lined, Filament Wound, Reinforced Plastic, Fiberglass BackedBF113 Disc Ductile Iron ASTM A-536 Grade 65-45-12BF114 Disc edge Stainless Steel Type 316 ASTM A-240BF115 Top stub shaft Stainless Steel Type 304 ASTM A-276 (Standard)Stainless Steel Type 316 ASTM A-276BF116 Bottom stub shaft Stainless Steel Type 304 ASTM A-276 (Standard)Stainless Steel Type 316 ASTM A-276BF117 Packing Buna NBF118 Bottom cover Cast Iron ASTM A-48 Class 40BF119 Cap screws Carbon Steel BF120 Squeeze pins Stainless Steel Type 304 ASTM A-479BF121 Thrust collar Stainless Steel Type 420BF122 Thrust collar shims BronzeBF123 Spring pin Stainless Steel Type 420BF124 O-ring Buna NBF125 Packing retainer NylonBF126 Bearings DuralonBF127 Disc Ductile Iron ASTM A-536 Grade 65-45-12BF128 Top stub shaft Stainless Steel Type 304 ASTM A-276BF129 Bottom stub shaft Stainless Steel Type 304 ASTM A-276BF130 Bottom cover Cast Iron ASTM A-126 Class BBF131 Bottom cover cap Cast Iron ASTM A-126 Class BBF132 Taper pins Stainless Steel Type 630 ASTM A-564 Cond. H-1150BF133 Lockwashers Stainless Steel Type 304BF134 Hex nuts Stainless Steel Type 304BF135 O-rings Buna NBF136 Thrust bearing stud Stainless Steel Type 304BF137 Thrust collar Bronze ASTM B-505 Alloy C93200BF138 Dowel pin Alloy Steel BF139 Bottom cover gasket Blended Fiber, Cured Nitril BinderBF140 O-ring Buna NLineseal III Butterfly Valve Replacement PartsShaded area indicates change Rev. 9-0911.10? EPDM rubber seat and seals? 304/316 Stainless Steel Fasteners? Additional 4 mils minimum Epoxy interior and/or exterior? Catalog number-- 5227-6 Flanged (Class 250) Ends; ANSI 250lb Drilling B16.1 Sizes--3", 4", 6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36", 42", 48"* ? 250psig (1723kPa) maximum working pressure ? Meets or exceeds all applicable requirements of ANSI/AWWA C504 Standard Class 250B; NSF 61 certified ? Body - Ductile Iron ASTM A-536 (65-45-12)? Buried service valves: I.D. and O.D. coated? Above ground valves (ordered with either a handwheel, position indicator on the actuator, or lever); minimum 8 mills epoxy coated interior and exterior; meets AWWA C-504 standards. ? Seat-in-body design reduces seat failure due to corrosive buildup in the valve and pipeline ? Disc edge is 316 Stainless Steel ? Disc - Ductile Iron ASTM A-536 (65-45-12) (3"-4" Stainless Steel ASTM A-531 CF8M)? Nonmetallic bearings prevent galvanic corrosion and provides lower coefficient of friction ? Chevron "V" type packing is self-adjusting to last the life of the valve ? 3"-24" Standard 304 SS hardware. Standard Buried Service ActuatorsNote: Actuator size subject to change based on actual pipeline conditions.? Holiday testing? Ground level position indicatorMUELLER® LINESEAL XP™ BUTTERFLY VALVES (CLASS 250B) 3" - 48"* Options? MDT Actuator with handwheel or chainwheel and position indicator? MDT Actuator with cylinder actuator (also available with manual override, handjack and 4-way solenoid valve)Slotted-Lever (3"-8")Link-Lever (10"-48")3"-20"24"-48"Valve size Actuator Number of turns3"-8" MDT-2S 3210"-14" MDT-3S 3016"-18" MDT-4S 4020"-24" MDT-5 4430"-36" MDT-5S 13642"-48" MDT-6S 215Rev. 9-09 Shaded area indicates changes11.11Dimension+Nominal size3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36" 42" 48"A 4.75 5.50 7.25 8.50 9.75 11.50 12.75 14.00 15.25 17.00 19.75 25.63 28.13 32.13 36.25B 3.25 3.50 8.38 9.63 11.00 12.63 13.88 15.13 16.38 17.63 20.25 26.00 31.13 35.13 39.63C 8.25 10.00 12.50 15.00 17.50 20.50 23.00 25.50 28.00 30.50 36.00 43.00 50.00 57.00 65.00D 5.00 5.00 6.00 8.00 8.00 8.00 12.00 12.00 12.00 12.00 12.00 12.00 15.00 15.00 15.00E 1.13 1.25 1.44 1.63 1.88 2.00 2.13 2.25 2.38 2.50 2.75 3.00 3.38 3.69 4.00F (number and size of holes)**8--.88 8--.88 12--.8812--1.0016--1.1216--1.2520--1.2520--1.3820--1.3820--1.3824--1.6220--2.0024--2.2528--2.2532--2.25-- -- -- -- -- -- -- -- 4--1.25 4--1.25 -- 8--1.50 8--2.00 8--2.00 8--2.00G 6.63 7.88 10.63 13.00 15.25 17.75 20.25 22.50 24.75 27.00 32.00 39.25 46.00 52.75 60.75J 4.69 4.69 4.69 4.69 5.63 5.63 5.63 6.38 6.38 7.56 7.56 7.56 8.31 11.13L 2.00 2.00 2.00 2.00 2.44 2.44 2.44 2.84 2.84 3.49 3.49 3.49 3.94 5.06Q 4.50 4.50 4.50 4.50 5.38 5.38 5.38 6.75 6.75 10.00 10.00 10.00 15.94 14.19R 8.25 8.25 8.25 8.25 10.38 10.38 10.38 11.31 11.31 17.00 17.00 17.00 19.88 26.50Turns to Open32 32 32 32 30 30 30 40 40 44 44 44 136 215Actuator (see notes) MDT-2S MDT-2S MDT-2S MDT-2S MDT-3S MDT-3S MDT-3S MDT-4S MDT-4S MDT-5 MDT-5 MDT-5 MDT-5S MDT-6SMUELLER® LINESEAL XP™ BUTTERFLY VALVES (CLASS 250B) 3"-48"* - FLANGE ENDSDimensions - for Lineseal XP Valves - Flange (ANSI B16.1 Class 250) Ends, 3"-48"* Sizes.+All dimensions are in inches. *Consult your Mueller representative for sizes larger than 48". **Top row: number and size of clearance holes for bolts; bottom row: number and size of threaded holes for studs. NOTES: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings are available upon request. Actuator size subject to change based on actual pipeline conditions.CONTACTFACTORYTAPPED HOLES UNC2B X E DEEPVALVE NO. TAPPED HOLESSIZE (EACH FLANGE)18" - 20" 4(2 OVER BOTH SHAFT AREAS) 30" - 48" 8(4 OVER BOTH SHAFT AREAS) Shaded area indicates change Rev. 10-1111.12? EPDM rubber seat and seals? 304/316 Stainless Steel Fasteners? Additional mils available Epoxy interior and/or exterior? Catalog number-- 5227-6 Flanged (Class 250) Ends*; ANSI B16.1 Class 125 Sizes--3", 4", 6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36", 42", 48"* 5227-20 Mechanical joint ends (with mechanical joint unassembled accessories) Sizes--4", 6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36", 42", 48"* 5227-23 Mechanical joint ends (without mechanical joint accessories) Sizes--4", 6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36", 42", 48"* 5227-16 Flanged x Mechanical joint ends (with mechanical joint accessories) Sizes--6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36" 5227-19 Flanged x Mechanical joint ends (without mechanical joint accessories) Sizes--6", 8", 10", 12", 14", 16", 18", 20", 24", 30", 36" ? 250psig (1723kPa) maximum working pressure ? Meets or exceeds all applicable requirements of ANSI/AWWA C504 Standard Class 250B; NSF 61 certified ? Body - Ductile Iron ASTM A-536 (65-45-12)? Buried service valves: I.D. and O.D. coated? Above ground valves (ordered with either a handwheel, position indicator on the actuator, or lever); minimum 8 mills epoxy coated interior and exterior. ? Seat-in-body design reduces seat failure due to corrosive buildup in the valve and pipeline (24"-48") ? Disc edge is 316 Stainless Steel ? Disc - Ductile Iron ASTM A-536 (65-45-12) (3", 4", 6" Stainless Steel ASTM A-531 CF8M)? Through-disc pinning provides a tight disc-to-shaft pin connection, greatly reducing the possibility of loosening through vibration ? Symetrical disc for higher Cv and lower head loss (3"-20")? Nonmetallic bearings prevent galvanic corrosion and provides lower coefficient of friction ? Chevron "V" type packing is self-adjusting to last the life of the valve * Consult your Mueller representative for sizes larger than 48" or for valves with Class 125 flanges.Standard Buried Service ActuatorsNote: Actuator size subject to change based on actual pipeline conditions.? Holiday testing? Ground level position indicatorMUELLER® LINESEAL XPII™ BUTTERFLY VALVES (CLASS 250B) 3" - 48"* Options? MDT Actuator with handwheel or chainwheel and position indicator? MDT Actuator with cylinder actuator (also available with manual override, handjack and 4-way solenoid valve)Slotted-Lever (3"-8")3"-20"24"-48"Valve size Actuator Number of turns3"-8" MDT-2S 3210"-14" MDT-3S 3016"-18" MDT-4S 4020"-24" MDT-5 4430"-36" MDT-5S 13642"-48" MDT-6S 215Rev. 9-09 Shaded area indicates changes11.13Dimension+Nominal size3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36" 42" 48"A 4.75 5.50 6.50 7.75 9.00 10.50 11.88 13.50 14.38 16.00 18.63 21.50 25.44 29.88 34.06B 3.25 3.50 5.13 6.50 9.88 11.38 12.75 14.38 15.25 16.88 18.38 24.13 28.00 32.69 36.88C 7.50 9.00 11.00 13.50 16.00 19.00 21.00 23.50 25.00 27.50 32.00 38.75 46.00 53.00 59.50D 5.00 5.00 5.00 6.00 8.00 8.00 8.00 8.00 8.00 8.00 8.00 12.00 12.00 12.00 15.00E .75 .94 1.00 1.13 1.19 1.25 1.38 1.44 1.56 1.69 1.88 2.13 2.38 2.63 2.75F (number and size of holes)4--.63 8--.63 8--.75 8--.75 12--.88 12--.88 12--1.00 16--1.00 16--1.13 20--1.13 20--1.25 28--1.25 32--1.50 36--1.50 44--1.50G 6.00 7.50 9.50 11.75 14.25 17.00 18.75 21.25 22.75 25.00 29.50 36.00 42.75 49.50 56.00J 4.69 4.69 4.69 4.69 5.63 5.63 5.63 6.38 6.38 7.56 7.56 8.31 8.31 9.88 9.88L 2.00 2.00 2.00 2.00 2.44 2.44 2.44 2.84 2.84 3.47 3.47 3.47 3.47 5.06 5.06Q 4.25 4.25 4.25 4.25 5.38 5.38 5.38 6.75 6.75 10.00 10.00 15.94 15.94 14.19 14.19R 8.25 8.25 8.25 8.25 10.38 10.38 10.38 11.31 11.31 17.00 17.00 19.88 19.88 26.50 26.50Turns to Open 32 32 32 32 30 30 30 40 40 44 44 44 136 215 215Actuator (see notes) MDT-2S MDT-2S MDT-2S MDT-2S MDT-3S MDT-3S MDT-3S MDT-4S MDT-4S MDT-5 MDT-5 MDT-5 MDT-5S MDT-6S MDT-6SMUELLER® LINESEAL XPII™ BUTTERFLY VALVES (CLASS 250B) 3"-48" - FLANGE ENDSDimensions - for Lineseal XPII Valves - Flange (ANSI B16.1 Class 125) Ends, 3"-48"* Sizes.+All dimensions are in inches. NOTES: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings are available upon request. Actuator size subject to change based on actual pipeline conditions.Shaded area indicates change Rev. 9-0911.14 MUELLER® LINESEAL XPII™ BUTTERFLY VALVES (CLASS 250B) 4"-48" - M.J. ENDSDimensions - for Lineseal XPII Valves - Mechanical Joint Ends, 4"-48" Sizes.NOTES: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings are available upon request. Actuator size subject to change based on actual pipeline conditions.+All dimensions are in inches. consult installation instructions supplied with valve for specific installation procedures.CAUTIONDimension+Nomnal Size4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36" 42" 48"A 5.50 6.50 7.75 9.00 10.50 11.88 13.50 14.38 16.00 18.63 21.50 25.44 29.88 34.06B 3.50 5.13 6.50 9.88 11.38 12.75 14.38 15.25 16.88 18.38 24.13 28.00 32.75 36.88C 9.00 11.00 13.25 15.56 17.94 20.31 22.56 24.69 27.09 31.56 39.00 45.88 53.00 59.88D 8.13 8.50 8.63 9.25 9.25 11.50 12.00 12.25 12.50 13.25 18.00 22.00 22.00 24.00E 1.00 1.00 1.13 1.19 1.25 1.31 1.38 1.38 1.50 1.63 1.81 2.00 2.00 2.00F (number and size of holes 4--.75 6--.75 6--.75 8--3/4 8--.75 10--.75 12--.75 12--.75 14--.75 16--.75 20--1.00 24--1.00 28-- 1.25 32-- 1.25G 7.50 9.50 11.75 14.00 16.25 18.75 21.00 23.25 25.50 30.00 36.88 43.75 50.63 57.50J 4.69 4.69 4.69 5.63 5.63 5.63 6.38 6.38 7.56 7.56 8.31 8.31 10.19 10.19L 2.00 2.00 2.00 2.44 2.44 2.44 2.84 2.84 3.47 3.47 3.94 3.94 5.06 5.06Q 4.25 4.25 4.25 5.38 5.38 5.38 6.75 6.75 10.00 10.00 15.94 15.94 14.19 14.19R 8.25 8.25 8.25 10.38 10.38 10.38 11.31 11.31 17.00 17.00 19.88 19.88 26.50 26.50X 3.13 3.50 3.63 4.25 4.25 4.50 5.00 5.25 5.50 6.38 10.00 14.00 14.00 16.00Turns to Open 32 32 32 30 30 30 40 40 44 44 136 136 215 215Actuator (see notes) MDT-2S MDT-2S MDT-2S MDT-3S MDT-3S MDT-3S MDT-4S MDT-4S MDT-5 MDT-5 MDT-5S MDT-5S MDT-6S MDT-6SRev. 9-09 Shaded area indicates changes11.15MUELLER® LINESEAL XPII™ BUTTERFLY VALVES (CLASS 250B) 6"-36" - FL x M.J. ENDSDimension+ Nomnal Size6" 8" 10" 12" 14" 16" 18" 20" 24" 30" 36"A 6.50 7.75 9.00 10.50 11.88 13.50 14.38 16.00 18.63 21.50 25.44B 5.13 6.50 9.88 11.38 12.75 14.38 15.25 16.88 18.63 24.38 28.25C 11.00 13.50 16.00 19.00 21.00 23.50 25.00 27.50 32.00 38.75 46.00CC 11.00 13.25 15.56 17.94 20.31 22.56 24.69 27.09 31.56 39.00 45.88D 6.75 7.31 8.63 8.63 9.75 10.00 10.13 10.25 10.63 15.00 17.00DD 4.25 4.31 4.63 4.63 5.75 6.00 6.13 6.25 6.63 9.00 11.00E 1.06 1.13 1.25 1.25 1.38 1.44 1.56 1.69 1.88 2.13 2.38EE 1.06 1.13 1.19 1.25 1.31 1.38 1.44 1.50 1.63 1.81 2.00F (number and size of holes 8--.75 8--.75 12--.88 12--.88 12--1.00 16--1.00 16--1.13 20--1.13 20--1.25 28--1.25 32--1.50FF 6--.75 6--.75 8--.75 8--.75 10--.75 12--.75 12--.75 14--.75 16--.75 20--1.00 24--1.00G 9.50 11.75 14.25 17.00 18.75 21.25 22.75 25.00 29.50 36.00 42.75GG 9.50 11.75 14.00 16.25 18.75 21.00 23.25 25.50 30.00 36.88 43.75J 4.69 4.69 5.63 5.63 5.63 6.38 6.38 7.56 7.56 8.31 8.31L 2.00 2.00 2.44 2.44 2.44 2.84 2.84 3.47 3.47 3.94 3.94Q 4.25 4.25 5.38 5.38 5.38 6.75 6.75 10.00 10.00 15.94 15.94R 8.25 8.25 10.38 10.38 10.38 11.31 11.31 17.00 17.00 19.88 19.88X 4.25 4.81 6.13 6.13 6.25 6.50 6.63 6.75 7.13 11.00 13.00Turns to Open 32 32 30 30 30 40 40 44 44 136 136Actuator (see notes) MDT-2S MDT-2S MDT-3S MDT-3S MDT-3S MDT-4S MDT-4S MDT-5 MDT-5 MDT-5S MDT-5SFQLJFFG(BOLTCIRCLE)CEEEDDDRGG(BOLTCIRCLE)CCA BXFFE EEDDDJF2 SQ AWWA NUTSPUR GEAR FURNISHEDON MDT-6SXCG(BOLTCIRCLE)4 1/2 MAXAQR3 1/2 SPACEREQUIRED FORTHRUST BEARINGCOVER REMOVALGG(BOLTCIRCLE)CCLBDimensions - for Lineseal XPII Valves - Flange Ends x Mechanical Joint Ends 6"-20" Sizes.+All dimensions are in inches. NOTES: These dimensions are correct at time of publication but are not to be construed as certified drawings. Certified drawings are available upon request. Actuator size subject to change based on actual pipeline conditions.Dimensions - for Lineseal XPII Valves - Flange Ends x Mechanical Joint Ends 24"-36" Sizes.When using 10" and 12" MJ End Valves on Class 200 C900 PVC Pipe, consult installation instructions supplied with valve for specific installation procedures.CAUTIONShaded area indicates change Rev. 9-0911.16 MUELLER® LINESEAL XP™ & XPII™ BUTTERFLY VALVES (CLASS 250B) 3"- 48"*-PARTS* Contact your Mueller representative for sizes larger than 48".BF106 BF117 BF100 BF112 BF103 BF102 BF101 BF110 BF112 BF105 BF107 BF108 BF109 BF111BF1123” and 4” XP10"–20" XPII3"–8" VALVES XPIIBF157BF150 BF126 BF134 BF133 BF100 BF126 BF114 BF153 BF145 BF119 BF156 BF130 BF154 BF117 BF125 BF110 BF132 BF135 BF127 BF151 24” XPII VALVESCatalog Part No. Description MaterialBF100 Body Ductile Iron ASTM A-536 (65-45-12)BF101 DiscDuctile Iron ASTM A-536 (65-45-12), Edge Type 316 Stain-less Steel (3" and 4" Cast Stainless Steel Grade CF8M)BF102 Shaft Stainless Steel ASTM A-564 Type 630 Cond. H-1150BF103 Squeeze Pin Stainless Steel ASTM A-564 Type 630 Cond. H-1150BF106 Key Steel AISI C-1045BF107 Cover Cast iron ASTM A-48 Class 40BF108 Lockwasher Stainless ASTM A-276 Type 304BF109 Capscrew Stainless ASTM A-276 Type 304BF110 Seat Buna N (EPDM optional)BF111 Plug Stainless SteelBF112 Bearings PTFE Lined Stainless Steel (3"-4" Nylon)BF114 Disc edge Stainless Steel ASTM A-240 Type 316 BF117 Packing Buna N Chevron V TypeBF119 Capscrews Stainless Steel Type 304BF125 Packing retainer NylonBF126 Bearings PTFE Lined, Fiberglass backedBF127 Disc Ductile Iron ASTM A-536 Grade 65-45-12BF130 Bottom cover Cast Iron ASTM A-126 ClassBBF131 Bottom cover cap Cast Iron ASTM A-126 ClassBBF132 Taper pins Stainless Steel Type 630 ASTM A-564 Cond. H-1150BF133 Lockwashers Stainless Steel Type 304BF134 Hex nuts Stainless Steel Type 304 BF135 O-rings Buna N (EPDM Optional) BF136 Thrust bearing stud Stainless Steel ASTM A-564 Type 630 Cond. H-1150 BF137 Thrust collar Bronze ASTM B-505 Alloy C93200 BF138 Groove pin Alloy Steel BF139 Bottom cover gasket Non Asbestos material ASTM F104 BF140 O-ring Buna N (EPDM optional) BF150 Top stub shaft Stainless Steel Type 630 ASTM A-564 Cond. H1150BF151 Bottom stub shaft Stainless Steel Type 630 ASTM A-564 Cond. H1150BF152 Squeeze Pins Stainless SteelBF153 O-ring Buna N (EPDM Optional)BF154 Thrust collar Bronze ASTM B-505 Alloy C93200BF156 Thrust shim Brass Alloy C26000 Half Hard (HO2)BF157 Key Carbon Steel ANSI 1018Lineseal XP & XPII Butterfly Valve Replacement PartsBF150BF117BF125BF110BF132BF135BF106BF127BF112BF134BF133 BF151BF100BF114BF140BF130BF137BF131BF119BF138BF112BF139BF13630” THRU 48”VALVES6"-20" XP VALVESRev. 9-09 Shaded area indicates changes11.171. Quantity:________________________________2. Size of Valve: ____________________________3. Body Style:_____ FLG x FLG (3"-48" ANSI B16.1 Class 125)_____ FLG x FLG (3"-48" ANSI B16.1 Class 250)_____ MJ x MJ (4"-48")_____ FLG x MJ (6"-36")_____ SLP x SLP (12" or 16")_____ FLG x SLP (12" or 16")Other: ___________________________________ Note: MJ valves are supplied without accessory kits standard. 4. Class of valve _______(150B or 250B)5. Please provide the following information in addition to the valve class (if known) listedin question 4.PRESSURE: Normal ______psig Maximum_____psigFLOW: Normal _______ psig Maximum ______psig 6. Type of service: Water _____ Air ______7. Type of operation: _____ Handwheel _____ Chainwheel _____ 2" Square nut ____Integral disc position indicator______ Extension stem (stem length) ____8. Direction of opening: _____ Counter clockwise ____Clockwise9. Coating Requirement*: ________mils of Ameron 370 (4 or 8 standard)10. Number of certificates of compliance to AWWA C504 required: __________________________________ __________________________________________MUELLER® LINESEAL III®, XP™, XPII™ BUTTERFLY VALVE ORDERING INSTRUCTIONSOrdering Instructions for MUELLER LINESEAL III, XP, XPII Butterfly Valves with Manual ActuatorsPlease note below any additional information or requirements such as extended bonnets and torque tubes, floor stand mounted actuators, special actuator positioning, and special coatings.PLEASE PROVIDE AS MUCH DESCRIPTIVE INFORMATION AND/OR SPECIFICATIONS AS POSSIBLE TO ENABLE US TO PROVIDE THE MOST SUITABLE VALVE FOR YOUR NEEDS. DO NOT HESITATE TO ATTACH ADDITIONAL PAGES. _______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Accessory items required (Stems Guides, Ground Line Position Indicators, Floor Stands, etc.) ** __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________*In order to provide valves that meet NSF 61 requirements and certify to that, Ameron 370 will be the paint supplied between 4-24mils thickness. Other paints or mil thickness greater 24 mils will not be NSF 61 compliant. ** Accessory items are listed on pages 11.3, 11.10 and 11.12Shaded area indicates change Rev. 9-0911.181. Quantity:________________________________2. Size of Valve: ____________________________3. Body Style:_____ FLG x FLG (3"-48" ANSI B16.1 Class 125)_____ FLG x FLG (3"-48" ANSI B16.1 Class 250)_____ MJ x MJ (4"-48")_____ FLG x MJ (6"-36")Other: ___________________________________Note: MJ valves are supplied without accessorty kits standard. 4. Class of valve _______(150B or 250B)5. Please provide the following information in addition to the valve class (if known) listed in question 4.PRESSURE: Normal ______psig Maximum_____psigFLOW: Normal _______ psig Maximum ______psig 6. Type of service: Water _____ Air ______7. Maximum Fluid Line Temperature ____________ °F.8. Direction of Opening: Counter Clockwise _______ Clockwise _______9. Power source Available: Volts _____ Phase _____ HZ _______10. Operating Time from Full Open to Full Close: Min. ________ Sec. ________11. Enclosure Classification: Weatherproof _________ Explosion Proof __________ Submersible _________12. Push Button Station Required: Yes _____ No ____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________MUELLER® LINESEAL III®, XP™, XPII™ BUTTERFLY VALVE ORDERING INSTRUCTIONSOrdering instructions for MUELLER LINESEAL III, XP, XPII Butterfly Valves with Electric Actuators13. Accessories: Manual Override _____ Limit Switches _____ Potentiometer _____ Reversing Starter ________ Motor Heater _____ Extended Duty Motor ______ Other _________________14. Valve Function: Open/Close _______ Modulating______15. Application: Buried ________ Submerged _____ In-plant ________ Above Ground _________16. Coating Requirement*: ________mils of Ameron 370 (4 or 8 standard)17. Number of Certificates of Compliance to AWWA C-504 required. ________________Please note below any additional information or requirements such as extended bonnets and torque tubes, floor stand mounted actuators, special actuator positioning, and special coatings.PLEASE PROVIDE AS MUCH DESCRIPTIVE INFORMATION AND/OR SPECIFICATIONS AS POSSIBLE TO ENABLE US TO PROVIDE THE MOST SUITABLE VALVE FOR YOUR NEEDS. DO NOT HESITATE TO ATTACH ADDITIONAL PAGES. ___________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Accessory items required (Stems Guides, Ground Line Position Indicators, Floor Stands, etc.): ** ________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________*In order to provide valves that meet NSF 61 requirements and certify to that, Ameron 370 will be the paint supplied between 4-24mils thickness. Other paints or mil thickness greater 24 mils will not be NSF 61 compliant. ** Accessory items are listed on pages 11.3, 11.10 and 11.12.Rev. 9-09 Shaded area indicates changes11.191. Quantity:___________________________________ 2. Size of Valve:________________________________ 3. Body Style: _____ FLG x FLG (3"-48" ANSI B16.1 Class 125)_____ FLG x FLG (3"-48" ANSI B16.1 Class 250)_____ MJ x MJ (4"-48")_____ FLG x MJ (6"-36")Other:_____________________________________ Note: MJ valves are supplied without accessorty kits standard. 4. Class of valve_______ 5. Please provide the following information in addition to the valve class (if known) listed in question 4. PRESSURE: Normal_____psig Maximum_____psig FLOW: Normal_____psig Maximum____psig 6. Type of service: Water____ Air______ 7. Cylinder Supply Available: Water____ Air____ Air/Oil____ Oil____ 8. Minimum Supply Pressure Available to Actuate Cylinder: __________________________psig 9. Fail Safe Spring Return Required? Yes ____ No ____ 10. Manual Override Required? Yes ____ No ____ 11. Accessories: Speed Control ____ Positioner ____ Solenoid____ Limit Switches (qty)____ Other _____________________________________ __________________________________________12. Cylinder Material: Non-Metallic____ Metallic____ 13. Valve Function: Open/Close___Modulating____MUELLER® LINESEAL III®, XP™, XPII™ BUTTERFLY VALVE ORDERING INSTRUCTIONS 14. Maximum Fluid Line Temperature_________°F.15. Coating Requirement*: ________mils of Ameron 370 (4 or 8 standard)16. Number of Certificates of Compliance to AWWA C-504 required. ______________________ Please note below any additional information or requirements such as extended bonnets and torque tubes, floor stand mounted actuators, special actuator positioning, and special coatings. PLEASE PROVIDE AS MUCH DESCRIPTIVE INFORMATION AND/OR SPECIFICATIONS AS POSSIBLE TO ENABLE US TO PROVIDE THE MOST SUITABLE VALVE FOR YOUR NEEDS. DO NOT HESITATE TO ATTACH ADDITIONAL PAGES. __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Accessory items required (Stems Guides, Ground Line Position Indicators, Floor Stands, etc.):** ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ *In order to provide valves that meet NSF 61 requirements and certify to that, Ameron 370 will be the paint supplied between 4-24mils thickness. Other paints or mil thickness greater 24 mils will not be NSF 61 compliant. **Accessory items are listed on pages 11.3, 11.10, and 11.12.†Please provide Cylinder Specifications if available. Ordering Instructions for MUELLER LINESEAL III, XP, XPII Butterfly Valves with Cylinder Actuators†Shaded area indicates change Rev. 9-0911.20www.muellercompany.com moreinfo@muellercompany.comRev. 9-09 Shaded area indicates changes