CDR Pompe - HTS - Metallic Magnetic Drive Turbine Peripheral Pumps Brochure

Compact, metallic magnetic driven regenerative turbine pumpsMaterials: AISI 316 (1.4401)Close-coupled executionMetallic Magnetic Drive Turbine Peripheral PumpsHTS RPompe S.P.A.Comply to : 2006/42/CEAvailable upon request :ATEXDirective 94/9/ECFlanges :UNI 1092-2 PN16 type B ANSI 150RFHTS WITH MOTORThe regenerative pump produces large head at comparatively small flows : a performance range that is not usually covered by standard centrifugal pumpsDesignReliabilitySuitable for handling aggressive, toxic and hazardous liquids (low viscosity, clean or slightly contaminated) in the chemical, petrochemical and pharmaceutical industries, where the need of high safety standards is the first requirementVersatilityMetallic Sealless Magnetic Drive Pumps suitable for service up to 140°C. The HTS series is designed with a rotating metallic shaft supported by single static bushingRPompe S.P.A.HTS range are Metallic Sealless Magnetic Drive horizontal turbine single-stage pumpsInner and Outer magnets are equipped with NdFeB (neodymium iron boron) or SmCo (samarium cobalt) permanent magnetsPatented cage magnet attachment guarantee stability during the operation of the pumpThe HTS are available in close coupled execution, suitable to be coupled with standard electrical motorsThe forced internal recirculation path design allows the pump to work properly along the whole performancesInternal recirculation path adjustable to match low or high viscosity medium work curveSealless designTotal containment, essential for hazardous, aggressive or valuable product.The design allows to the Isolation Shell to be self-ventingThe standard execution made by Hastelloy C276 reduces drastically the Eddy Current LossesThe problem of reverse rotation during start-up has been eliminate thanks to the key driven systemInner Magnet - Pump ShaftMagnets fully encapsulated with tough 316L sheathCoupled to the impeller by key, dome nut and locking tab washerMag drive conceptThe synchronous drive configuration is based on an outer magnet ring assembly built to magnetically couple with an inner magnet ring assembly. These two magnet rings are locked together by the flux of attracting magnet poles flowing through the containment isolation shellCan operate without axial or radial thrusts thanks to the impeller design, eliminating wear on axial thrust bearing www.cdrpompe.itTECHNICAL SPECIFICATIONSPart listDIN Component Material102 Casing AISI 316 (CF8M)157 Isolation Shell Hastelloy C + AISI 316L211 Pump Shaft AISI 316 (1.4401)230 Impeller AISI 316 (1.4401)344 Lantern GS400350 Bushing Support AISI 316L (CF3M)411.x Joint Ring (Casing) PTFE502 Casing Wear Ring PTFE-CF \\\\ PEEK504 Spacer Ring PTFE510 Thrust Bearing SiC529 Bearing Sleeve SiC545 Bearing Bush SiC \\\\ PEEK855 Inner Magnet AISI 316L (1.4404)856 Outer Magnet GS400QH2900rpm020406080100120140160m1807.50.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7m3\\\\hHTS 100HTS 90HTS 80HTS 130HTS 110HTS 1050QH1450rpm0610141624m2400.5 1 1.5 2 2.5 3 3.5m3\\\\h32HTS 100HTS 90HTS 80HTS 130HTS 110HTS 1054850 HzTechnical Specifications60 HzQH1750rpm06102030m506013700.5 1 1.5 2 2.5 3 3.5m3\\\\h40HTS 100HTS 90HTS 80HTS 130HTS 110HTS 105QH3500rpm102030405060708090m1007.50.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7m3\\\\hHTS 100HTS 90HTS 800Performances 2900 rpm Q max = 5 m3/h -> H max = 160 mclElectric Motors 0.75 kW (motor size 80) -> 7.5 kW (motor size 132)Temperature range - 30°C -> +140°CAllowable Pressure Range 20 bar @ 20 °CThreaded ConnectionsHTS series G1” X G1”* as option : Flanges DN25 ISO 1092 PN16RF or ANSI 150 RFViscosity 1cSt min - 200 cSt maxAllowable Solids No solids are allowedNot binding data refers to water at room temperature. For specific performance curve contact CDR Pompe SpA.For further info, please visit www.cdrpompe.comC.D.R. Pompe S.p.A.Via P. Togliatti, 26/A - 20030 Senago (MI) - ItalyTel. +39029901941 Fax +39029980606www.cdrpompe.com info@cdrpompe.itRPompe S.P.A.Technical CharacteristicsThe technical data and characteristics stated in this General Catalogue are not binding. CDR Pompe S.p.a. reserves the right to make modifications without notice. Therefore data, dimensions, performances and any other stated issues are indicative only and not binding. Anyway for any technical details you must require an up-to-date product technical card.TB - HTS 2012.01