Claris® Series Filter Cartridges Brochure (PDF 47 KB)

Data Sheet 1251-DCLARIS® SeriesFilter CartridgesHigh Consistency Polypropylene Melt BlownCartridge• Graded Pore Structure Enhances Dirt Holding Capacity• E-core, an Extruded Fibrous Core, Provides ExcellentStrength• Unique Proprietary Process• Easy and Safe Cartridge Incineration and Disposal• All Polypropylene Construction• Free of Surfactants, Binders, and Adhesives• Plastic and Metal Spring Assembly End ConfigurationsAvailablePerformance SpecificationsFilter Grades:1, 3, 5, 10, 20, 30, 50, 75 micron (µm)Maximum Differential Pressure: 50 psid (3.45 bar) @ ambient25 psid (1.72 bar) @ 140°F (60°C)Recommended Change Out Differential Pressure1:35 psid (2.4 bard)Purity:Claris Series fi lter cartridges are free of surfactants, anti-static agents, binders, and adhesives.Product SpecificationsMaterials of Construction:Filter Media: PolypropyleneEnd Caps2: PolypropyleneExtended Core2: Stainless SteelExtruded Core: PolypropyleneGaskets/O-rings2: Silicone Elastomer, Buna N, Viton3 A,EPDM, Santoprene4Dimensions (nominal):Outside Diameter: 2 1/2" (6.4 cm)Inside Diameter: 1" (2.7 cm)Lengths: 9 3/4" (24.8 cm), 9 7/8" (25.1 cm),10" (25.4 cm), 19 1/2" (49.5 cm),19 4/5" (50.3 cm), 20" (50.8 cm),29 1/4" (74.3 cm), 29 1/2" (74.9 cm), 29 3/4" (75.6 cm), 30" (76.2 cm),39" (99.1 cm), 40" (102 cm),50" (127 cm)1 - Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.2 - These components are not NSF certified.3 - Registered trademark of DuPont Dow Elastomers.4 - Registered trademark of Advanced Elastomer Systems.Visit us on the Web at www.pall.comPall Corporation has offices and plants throughout the world in locations including:Argentina, Australia, Austria, Belgium, Brazil, Canada, China, France, Germany, India,Indonesia, Ireland, Italy, Japan, Korea, Malaysia, Mexico, the Netherlands, New Zealand,Norway, Poland, Puerto Rico, Russia, Singapore, South Africa, Spain, Sweden, Switzerland,Taiwan, Thailand, United Kingdom, United States, and Venezuela. Distributors are located inall major industrial areas of the world.Bulletin #1251-8D 5/07© Copyright 2007, 2005, Pall Corporation. Pall, and Claris are trademarks of Pall Corporation. ® Indicates a Palltrademark registered in the USA. is a service mark of Pall Corporation.Code Filter n Grades51 1 µm3 3 µm5 5 µm10 10 µm20 20 µm30 30 µm50 50 µm75 75 µmTypical Flow vs. Differential Pressure for Application SizingPart Numbers/Ordering InformationCLR n – l t u (e.g. CLR 3–20DOES)Code Gasket/O-ringu MaterialsS SiliconeN Buna NE EPDMV Viton AFlow rate is per 10" (25.4 cm) cartridge. For liquids other than water, multiply differential pressure by fluid viscosity (cP)..03.02.010DifferentialPressure(psid)Bar(x100=kPa)10µm20µm.45.4.35.3.25.2.15.1.0501 2 3 4 5 6 7 8 9 10Flow Rate (gpm), Water at 68°F (20°C)30 µm50 µm75 µm1µm3µm5µmCode Cartridge l Lengths(nominal)9.75 9.75"9.875 9.875"10 10"19.5 19.5"19.8 19.8"20 20"29.25 29.25"29.5 29.5"29.75 29.75"30 30"39 39"40 40"50 50"Code End ConfigurationstBlank DOE industrial (no end caps)DOE DOE with elastomer gasket seals & end capsH21 DOE, Santoprene gasket seal1X DOE industrial, 1" (2.54 cm) stainless steelextended coreM3 SOE flat closed end, external 222 O-rings(retrofits other manufacturers’ Code 0)6M6 SOE flat closed end, external 226 O-rings(retrofits other manufacturers’ Code 6) 6M7 SOE fin end, external 226 O-rings (retrofits other manufacturers’ Code 7) 6M8 SOE fin end, external 222 O-rings (retrofits other manufacturers’ Code 5)6M18 SOE flat closed end, external 222 O-ringXK SOE plastic spring assembly, saw cut endSI SOE metal spring/polypropylene cap, saw cut end5 - Based on typical application usage.6 - For details, contact Pall Corporation.Flow Rate (lpm)0 4 8 12 16 20 24 28 32 3625 Harbor Park DrivePort Washington, New York 11050 USA1.800.360.7255 toll free (Only in US)1.516.484.5400 phone1.516.625.3610 fax