Conax Technologies Products Catalouges

T E C H N O LO G I E S™68 Tel: 1.716.684.4500 • USA Toll Free: 1.800.223.2389 • Email: info@conaxtechnologies.com • Website: www.conaxtechnologies.com5001CBSWS SERIES ¦ SENSOR WIRE SEALSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSCap StyleA – has mounting thread onlyB – has cap end threadedCatalog Numbering SystemSealantV – VitonGland StyleBSWS4• 1/2 NPTBSWS5• 3/4 NPTGland StyleNumber of Elements SealedSealantElement SizeExample: BSWS4-20-A3-VCap StyleNumber of Elements Sealed234567891011121314See Specifications Chart for maximum wiresaccommodated by each model.Conax Technologies BSWS assemblies were originally designed for usewith embedded bearing temperature sensors to prevent oil migratingalong the sensor leads. They seal on the individual insulated leadsexiting an oil-filled bearing house. They may also be used to seal alltypes of insulated instrumentation leadwire. These sealing assembliescan be found in large motors, generators, turbines, pumps,compressors and journal bearing pedestals.Construction consists of 303SST standard bodies, caps and followerswith a Viton sealant. Standard assemblies seal 2 to 14 wires in avariety of wire gauges. Please consult Conax Technologies for custom needs.• Temperature Range: Ambient to +100° F (+37.8° C)• Pressure Range: to 50 psig (3.4 bar)AccessoriesThe replaceable sealant permits repeated use of the same fitting.Elements can be easily assembled or replaced in the field. To replacethe sealant or elements, simply loosen the cap, replace the necessaryitems, relubricate and retorque the cap.Glands are supplied factory lubricated. If glands are cleaned prior to assembly or when reused, the glands should be relubricated tomaintain the published torque and pressure ratings. See page 103 for information on our lubrication kit.To order a Replacement Sealant, order RS – (Gland) – (Element) – (Number of Holes) – (Sealant)Example: RS-BSWS4-20-2-VElement Size20• 0.044-0.059" dia. over insulation22• 0.037-0.051" dia. over insulation24• 0.032-0.045" dia. over insulation26• 0.028-0.041" dia. over insulation125 • 0.123-0.127" dia. over insulationBEARING WIRE SEALS (BSWS)Conax Technologies Sensor Wire Seals are designed to seal virtuallyany transducer, sensor or detector elements in a wide range of vacuum or pressure boundaries.The most common use of these seals is for instrument leads onvibration transducers, proximity probes, pressure sensors, temperaturesensors, flow meters, and strain gages. Virtually any sensor leadthat passes through a pressure boundary can be sealed using oneof our compression seal fitting styles.Don’t hesitate to contact our sales engineers directly with yourspecific needs.SENSORWIRESEALST E C H N O LO G I E S™69Tel: 1.716.684.4500 • USA Toll Free: 1.800.223.2389 • Email: info@conaxtechnologies.com • Website: www.conaxtechnologies.com5001CSENSOR WIRE SEALS ¦ TWS SERIESASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSASSEMBLYINSTRUCTIONSDiameter Over Hex Size Pressure RatingNumber Insulation Thread NPT Length ‘A’ Length ‘B’ Body Cap Body Cap VitonCatalog Number of Wires IN MM IN IN MM IN MM IN IN MM MM PSIG BARBSWS4-20 2-8 0.044-0.059 1.1-1.5 1/2 2.50 63.5 3.25 82.6 1.000 1.000 25.4 25.4 50 3BSWS4-22 2-8 0.037-0.051 0.9-1.3 1/2 2.50 63.5 3.25 82.6 1.000 1.000 25.4 25.4 50 3BSWS4-24 2-8 0.032-0.045 0.8-1.1 1/2 2.50 63.5 3.25 82.6 1.000 1.000 25.4 25.4 50 3BSWS4-26 2-8 0.028-0.041 0.7-1.0 1/2 2.50 63.5 3.25 82.6 1.000 1.000 25.4 25.4 50 3BSWS5-20 2-14 0.044-0.059 1.1-1.5 3/4 2.88 73.0 3.63 92.1 1.250 1.500 31.8 38.1 50 3BSWS5-22 2-14 0.037-0.051 0.9-1.3 3/4 2.88 73.0 3.63 92.1 1.250 1.500 31.8 38.1 50 3BSWS5-24 2-14 0.032-0.045 0.8-1.1 3/4 2.88 73.0 3.63 92.1 1.250 1.500 31.8 38.1 50 3BSWS5-26 2-14 0.028-0.041 0.7-1.0 3/4 2.88 73.0 3.63 92.1 1.250 1.500 31.8 38.1 50 3BSWS5-125 2-4 0.123-0.127 3.1-3.2 3/4 2.88 73.0 3.63 92.1 1.250 1.500 31.8 38.1 50 3BSWS5-120-B2-G 2 0.115-0.130 2.9-3.3 3/4 2.88 73.0 3.63 92.1 1.250 1.500 31.8 38.1 50 3BSWS5-120-B4-G 4 0.115-0.131 2.9-3.4 3/4 2.88 73.0 3.63 92.1 1.250 1.500 31.8 38.1 50 3BSWS5-120-B6-G 6 0.115-0.132 2.9-3.5 3/4 2.88 73.0 3.63 92.1 1.250 1.500 31.8 38.1 50 3Specifications – BSWSBSWS assemblies may be purchased with SAE/MS thread mount, weld neck or flange style mounts. Consult factory for details.All pressure and torque ratings were determined at 68° F (20° C) using stainless steel rod as the element. Pressure ratings may degrade at higher temperatures.Pressure rating guide values are provided for glands with elements restrained by the compressed sealant. Higher pressure may be attained with additional element restraints.For proper assembly of these sealing glands, see the Assembly Instructions provided on page 110.* Hex size for the body and cap are the same unless a cap size is provided in parentheses.TRANSDUCER WIRE SEALS (TWS)This version of the Conax sensor wire seal is designed to sealtransducer cables entering low-pressure oil-filled cavities in rotatingequipment. Since these transducers are typically manufactured with afactory assembled sensor and connector, the sealing gland has splitinternals to seal the outside jacket of the transducer’s cable.The Transducer Wire Seal comes standard with a four hole split Vitonsealant and with four split Teflon backing disks. The backing disks willhave 1, 2, or 3 holes so one sealing gland can seal up to threevibration, proximity and pressure transducer sensor cables.And unlike competitors’ designs, the Conax design requires only one Teflon backing disk and does not require the end user to punch out the holes.Call Conax today to learn more about complete line of sensor wire seals – and how we can customize a solution for your application.FIBEROPTICASSEMBLIES Page68_5001C_Rev_02_09 Page69_5001C_Rev_02_09