DeviceNet - HI 200DNWM - Weigh Module Brochure

SET POINTSTwo independent TTL level outputs provide set point capability each with separate deadbands and preacts for control capabilities in a variety of weighing applications.C2® ELECTRONIC CALIBRATIONC2 enables electronic calibration of the weigh system without test weights. This saves system start-up costs and aggravation. Of course, even if C2 certified load sensors are not used, the system can still be calibrated the slow, traditional way using certified test weights.WAVERSAVER®WAVERSAVER eliminates the effects of unwanted plant vibration on or around the scale by permitting the weigh module to “see” through the unwanted vibration signals - as low as 0.25Hz - while yielding a stable actual reading.THE BUTTON®With one push of a button the weigh scalemodule automatically calibrates the weighingsystem, making it ready for use. This saves system start-up time costs and aggravations.ADDITIONAL FEATURESThis module comes with a disk containing theElectronic Data Sheet (EDS) and a user'smanual. This product is available for dual stacking in an instrument cabinet, on standoffs, or on din rail, It is also available with a summing card packaged in a painted steel NEMA 4 or Stainless steel NEMA 4x junction box.ApplicationsPROCESS WEIGHING• Batching/Blending• Filling/Dispensing• Level-by-Weight• Check Weighing• Force MeasurementFeaturesWAVERSAVER®• Ignores vibration on and around scalesC2® Electronic Calibration• Electronic calibration without test weightsTHE BUTTON• One step calibration with C2 load cellsTWO SET POINTS• TTL LevelCONFORMANCE TESTEDThe HI 200DNWM is a general purpose weigh module designed specifically to the DeviceNet Open Network Standard. Its' many features, including "calibration with the push of a button", have set the norm for all future DeviceNet weighing products.FEATURES• The HI 200DNWM Series B now allows easier programming and increased flexibility through features such as:• A "Command Interface" for easy access to all parameters without the use of explicit messages• A choice of outputs with selectable decimal point location • A selectable update rate of 10 or 55 samples per secondThe HI 200DNWM supports up to eight C2® certified load sensors and provides power to scales with up to four 350-ohm standard strain gauge load cells, load sensors or load points. It receives and digitizes the weight signal with overone million bits of resolution, and transmits the selectable Gross, Net and Tare weight data over the DeviceNet Open Network interface to otherdevices. Data is transmitted at three switch selectable baud rates of 125, 250 or 500 kilobytes per second. The DNWM acts as a slave on the network and supports a polling I/O exchange mechanism. Two on-board bi-colorLEDs provide module and system status for troubleshooting.www.hardysolutions.com • 800-821-5831DeviceNet Weigh ModuleModel HI 200DNWM Series BSPECIFICATIONSTo learn more about the HI 200DNWM visit our website for:• full product specifications• ordering information• application notes• technical description• operator’s manualwww.hardysolutions.comor call us: 800-821-5831+1-858-278-2900www.hardysolutions.com • 800.821.5831ORDERING INFORMATION• Options OrderingOptions can be ordered at the same time the module is ordered by adding the dash designators to the end of the module number. Input Power• Provided from DeviceNet cable• 24 VDC ±1% network• 11-25 VDC NodeDeviceNet• Type: Generic• I/O Slave Messaging: Polling• Profile: Refer to EDS• Baud Rates: 125K, 250K, and 500KInputs• Weight: Metric or English• Zero and Tare• WAVERSAVER®• Calibration Type• Span Weight (Hard Cal)• Cal Low value• Cal High value• Number of C2 Sensors (C2 cal)• Number of averages• Set point on and/or two• Mode, value, deadband and preactsOutputs• Gross, Net, Tare weightsResolution• 20-bit Update Rate• 10 or 55 per second*Non-Linearity• 0..0015%Averages• 0-255 selectableTemperature Coefficient• < 0.0005% per degree C for zero and spanExcitation• 5 VDC internal drives four 350-ohmDimensions• HI 200DNWM: 3.8" W x 8.5" L x 1" T• HI 200DNWM-DR: 3.94" W x 8.6" L x 2" T• HI 200DNWM-SK1: 3.8" W x 8.5" L x 2.38" T• HI 200DNWM-SK1-DR: 3.94" W x 8.6" L x 3.31" T• HI 200DNWM-SS: 10" W x 8" L x 4" T• HI 200DNWM-PS: 10" W x 8" L x 4" TApprovals• CEWarranty• Two-year warranty against defects in workmanship*WAVERSAVERSetting Frequency Update Rate0 Off 55/sec1 4Hz 55/sec2 2Hz 10/sec3 1Hz 10/sec4 0.5hZ 10/secAll specifications subject to change without notice. Please contact the Hardy factory or visit our website for the latest specifications.Hardy Process Solutions9440 Carroll Park Dr.San Diego, CA 92121tel. +1-858-278-2900tel. 800-821-5831fax +1-858-278-6700www.hardysolutions.comhardyinfo@hardysolutions.comSince 1993HI 200DNWM 05110400-0004AAll information within is subject to change without notice. Visit our website for latest specifications. WAVERSAVER, C2, IT, THE BUTTON, ADVANTAGE and ANY-WEIGH are registered trademarks of Hardy Process Solutions, Inc.. Allen-Bradley and Encompass are trademarks of Rockwell Automation, Inc. All other trademarks or registered trademarks are the property of their respective owners.For example:HI 200DNWM DeviceNet Weigh Module standoff mounting. Includes THE BUTTON®, C2®,WAVERSAVER®, instruction manual & EDS on 3½" floppy disk.HI 200DNWM-DR with Din rail mounting kitHI 200DNWM-SK with module stacking kit. Includes hardware for stacking a second HI 200DNWMHI 200DNWM-SK1 Two complete weigh modules pre-stacked for standoff mounting. Includes THE BUTTON, C2, WAVERSAVER, instruction manual & EDS on 3½" floppy disk.HI 200DNWM-SK1-DR with Din rail mounting kitHI 200DNWM-SS DeviceNet Weigh Module with Summing Card in a stainless steel NEMA 4x enclosure with conduit hubs. Includes THE BUTTON, C2, WAVERSAVER, instruction manual & EDS on 3½" floppy disk.HI 200DNWM-PS DeviceNet Weigh Module with Summing Card in a painted steel NEMA 4 enclosure with conduit hubs. Includes THE BUTTON, C2, WAVERSAVER, instruction manual & EDS on 3 ½" floppy disk.Hardy Bench Scales, Floor Scales and Load PointsHardy carries a wide variety of strain gauge load points and scale bases to accommodate your application requirements.Hardy C2 Certified CableThis 8-conductor cable is designed for optimizing weight and load sensor characteristic signals from the junction box to the instrument.Hardy Junction Box (HI 215 Series) This NEMA 4 rated waterproof enclosure sums from one to four load sensor signals. ADVANTAGE Series Load Point with C2 CalibrationANY-WEIGHScalesCOMPONENTS TO COMPLETE YOUR HARDY SYSTEM MAKESTOCKPACKSHIP