Filtomat - 102C-110P - Liquidfiltration Brochure

FILTOMAT/M102C-110PAutomatic self-cleaningThe ideal filtrationsolution for a widerange of applicationsLow Cost High PerformanceAutomaticSelf-CleaningWater Filter*Patented innovative technology*No external power required*Filtered water continues to flow to the system during the backflush cycle*Easy to install and maintain*Self-locking mechanism to prevent over-flushing*Short pay-back periodHow the M102C-104C works :How the M104LP-M110P works:When flushing is completed, a second flushing cycle is automati-cally triggered, pushing the col-lector assembly downwards to itsoriginal position. the combinedflush cycle takes 6-10 seconds.The combined spin and axial movements ensure that the suction nozzles sweep the entirescreen area.When flushing is completed, a second flusing cycle is automatically triggered, pushing the col-lector assembly to its original posi-tion. the combined flush cycletakes 10-15 secondes.Water is filtered through the finescreen (1) to outlet (2). As dirtaccumulates on inner face offine screen, pressure differentialbuilds up. At a preset level, therinse controller (3) opens flushingvalve (4), creating a strongbackflush stream to atmosphere.This backflush creates a suctioneffect at nozzles (5), cleaningthe face of the fine screendirectly in front of nozzle open-ings. Backflush water now flowsthrough collector pipe (6), viahydraulic rotor (7) to flushingvalve, causing the dirt collectorassembly (8) to spin. Pressuredrop in rotor chamber (9) forcesthe collector assembly upward.The combined spin and upwardmovements ensure that the suc-tion nozzles sweep the entirescreen area.The special design of the nozzlecreates an additional streamthat also cleans the back side ofthe screen.Water enters the filter throughthe inlet (1) and is pre-filtered through the coarse screen (3) and then is filtered through the fine screen (4). From there it passes to the outlet (2). As dirt accumulates on inner face ofthe fine screen, pressure differ-ential builds up. At a presetlevel, the rinse controller (12)opens flushing valve (9), creat-ing a strong backflush streamthrough the drainage (11) to the atmosphere. This backflush cre-ates a suction effect at nozzles (6), cleaning the face of the fine screen directly in front of thenozzle openings.Backflush water now flowsthrough collector pipe (7) viahydraulic rotor (8) to flushingvalve, causing the dirt collectorassembly (7) to spin. Pressuredrop in rotor assembly (5) anddrainage of piston (10) forcesthe collector assembly into axialmovement.14NO. MODELM102CM103CM103CLM104CFlowM3/H25404080Screen AreaCM2580580900900Total heightMM570570700Weight, kgsEmpty222530Full384057Approx. rinsecycle time6-10 sec.6-10 sec.6-10 sec.23700 35 62l 6-10 sec.Screen available for all models: 50,80,100,120,150,200,400,800,1500,3000 micron.Maximum working pressure for all models: 10 bar gauge.Minimum upstream line pressure required during rinse cycle for all models: 2 bar, for 50 mic. screen3bar.Maximum working temperature for all models: 65°C.Drain line connection for all Models: 1 1/2” bsp female.Main drain header must be minimum 1 1/2” nominal bore.M102C M103CM104CM103CLDRAIN OUTLET1 1/2” B.S.P.FEMALEDRAIN OUTLET1 1/2” B.S.P.FEMALEDRAIN OUTLET1 1/2” B.S.P.FEMALEDRAIN OUTLET1 1/2” B.S.P.FEMALEOUTLETDN 50OUTLETDN 80OUTLETDN 100OUTLETDN 80INLETDN 50INLETDN 80 INLETDN 100INLETDN 80DRAIN1”B.S.P.DRAIN1”B.S.P.DRAIN1”B.S.P.DRAIN1”B.S.P.V&T Group BVEinsteinstraat 83281 NJ NumansdorpTel : ++31 (0)186 574151*Fax: ++31 (0)186 573722E-mail : info@v-tfiltergroup.comhttp//:www.v-tfiltergroup.comN° MODEL øD4”NB4”NB6”NB6”NB8”NB10”NBFlowM3/H100100180120320400Screen areaCM2flat300045003000450045004500zig-zag9000135009000135001350013500Dimensions, MML202524852090248526852685A320040603265406042604260465875480875965965H510510570510570585C235235270235270285øEpipe10”NB10”NB12”NB10”NB12”NB12”NBF300350350350460460Weight kgempty90110115120140160full170215225230320355123456BM104LPM104XLPM106LPM106XLPM108LPM110PScreen available flat: 50,80,100,120,150,200,400,800,1500,3000 micron.zig-zag: 15,25,30,40,50,80,100,120,150,200,400,800,1500,3000 micron.Pressure losses for maximum flow capacity: 0,2 bar.Maximum working pressure: 10 bar g.Minimum upstream line pressure required during rinse cycle for all models: 2 barg,3 barg for screen< 80 mic.Maximum working temperature: 65°CApproximate rinse cycle time: 10-15 sec.Backflush flow: 30-35 m3/hStandard of inlet/outlet flanges: DIN 10.M104LP