Geotex - 200ST - Woven Slit Film Datasheet

Geotex®, Landlok®, Pyramat®, X3®, SuperGro®, Petromat® and Petrotac® are registered trademarks of Propex Inc. THIS PUBLICATION SHOULD NOT BE CONSTRUED AS ENGINEERING ADVICE. WHILE INFORMATION CONTAINED IN THIS PUBLICATION IS ACCURATE TO THE BEST OF OUR KNOWLEDGE, PROPEX DOES NOT WARRANT ITS ACCURACY OR COMPLETENESS. THE ULTIMATE CUSTOMER AND USER OF THE PRODUCTS SHOULD ASSUME SOLE RESPONSIBILITY FOR THE FINAL DETERMINATION OF THE SUITABILITY OF THE INFORMATION AND THE PRODUCTS FOR THE CONTEMPLATED AND ACTUAL USE. THE ONLY WARRANTY MADE BY PROPEX FOR ITS PRODUCTS IS SET FORTH IN OUR PRODUCT DATA SHEETS FOR THE PRODUCT, OR SUCH OTHER WRITTEN WARRANTY AS MAY BE AGREED BY PROPEX AND INDIVIDUAL CUSTOMERS. PROPEX SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM PROVISION OF SAMPLES, A COURSE OF DEALING OR USAGE OF TRADE. P R O D U C T D A T A S H E E T GEOTEX® 200ST ©2006 Propex Inc. P r o p ex In c . P H : 4 2 3 8 9 9 0 4 4 4 6 0 2 5 L e e H i gh w a y , S u i t e 42 5 P H : 8 0 0 6 2 1 1 2 7 3 P O B ox 2 2 7 88 F A X : 4 2 3 8 99 7 6 1 9 C h a t t an o o g a , T N 3 7 4 2 2 w w w. g e o te x t i l e . c o m GEOTEX 200ST is a woven slit film geotextile produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. The individual slit films are woven together in such a manner as to provide dimensional stability relative to each other. The construction of the geotextile makes GEOTEX 200ST ideal for soil separation and stabilization and meets AASHTO M288 Class III standards. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX 200ST conforms to the property values listed below.1 Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). MARV2 PROPERTY TEST METHOD ENGLISH METRIC Mechanical Tensile Strength (Grab) ASTM D-4632 200 lbs 890 N Elongation ASTM D-4632 12 % 12 % Puncture ASTM D-4833 90 lbs 400 N CBR Puncture ASTM D-6241 460 psi 3170 kPa Mullen Burst ASTM D-3786 75 lbs 330 N Trapezoidal Tear ASTM D-4533 200 lbs 890 N Endurance UV Resistance % Retained at 500 hrs ASTM D-4355 70% 70% Hydraulic Apparent Opening Size (AOS)3 ASTM D-4751 40 US Std. Sieve 0.425 mm Permittivity ASTM D-4491 0.05 sec-1 0.05 sec-1 Water Flow Rate ASTM D-4491 4 gpm/ft2 160 l/min/m2 Roll Sizes 12.5 ft x 432 ft 15.0 ft x 360 ft 17.5 ft x 309 ft 3.81 m x 131.7 m 4.57 m x 109.8 m 5.33 m x 94.2 m NOTES: 1. The property values listed above are effective 05/2008 and are subject to change without notice. 2. Values reported in weaker principal direction. All values listed are Minimum Average Roll Values (MARV) unless otherwise noted, calculated as the typical minus two standard deviations. Statistically, it yields a 97.7% degree of confidence that any samples taken from quality assurance testing will exceed the value reported. Maximum Average Roll Value (MaxARV) is calculated as typical plus two standard deviations. 3. Maximum average roll value.