HARMSCO - Model FSSS - Single Cartridge Housings Brochure

HARMSCO® FSSSSingle Cartridge HousingsHARMSCO® Filtration ProductsFSSS Series Filter Housings are designed with a double o-ring compression which allows for positive sealing and easy access. Offered in DOE (double open end) or 222/Flat configurations.LubricantsPlating SolutionsHigh Purity WaterInksProcess Water FiltrationReverse Osmosis Pre-filtrationFood & Beverage FiltrationCutting Fluids304 or 316 stainless steel construction300 PSI (20.7 bar) pressure ratingElectro-polished finishOffered in Double Open End or 222 / Flat configurationsDouble o-ring compression seal for easy change outIncludes 1/8” NPT vent and 1/8” NPT drainInline design for easy installationStandard with wrench and mounting bracketKnife edge seal at both cartridge ends to eliminate by-pass for DOE cartridgesDesigned for 300 psi in 304 or 316 stainless steel.FSSS-1SeriesFSSS-2SeriesCommercial / IndustrialFeatures Applications Flow Rate (GPM)Pressure Drop (PSI)00 10 20 30 4012345Finish - electro-polishedInlet/Outlet - 3/4” on 9-3/4” housings and 1” on 20” housingsTemperature - up to 250°F (121°C)(filter housing only)Pressure - up to 300 PSI (20.7 bar) maxO-ring Closure Seal - silicone (standard)Construction - 304 or 316 stainless steelFilter Model Length Inlet/OutletPipe SizeEndConfigurationMaterial AFilter Ht.BI/O WidthCDiameterDInletFSSS-1A 9-3/4” 3/4” DOE 316 SS 13” 3.2” 4.06” 11.84FSSS-1B 9-3/4” 3/4” DOE 304 SS 13” 3.2” 4.06” 11.84FSSS-1A-222 9-3/4” 3/4” 222/Flat 316 SS 13” 3.2” 4.06” 11.84FSSS-1B-222 9-3/4” 3/4” 222/Flat 304 SS 13” 3.2” 4.06” 11.84FSSS-2A 20” 1” DOE 316 SS 23” 3.2” 4.06” 21.84FSSS-2B 20” 1” DOE 304 SS 23” 3.2” 4.06” 21.84FSSS-2A-222 20” 1” 222/Flat 316 SS 23” 3.2” 4.06” 21.84FSSS-2B-222 20” 1” 222/Flat 304 SS 23” 3.2” 4.06” 21.849-3/4”20”Harmsco® Single Cartridge Housings FSSSFSSS-1SeriesFSSS-2Series222 / Flat 222 /FlatOptional Housing Selection for different styleEnd Cap ConfigurationsDOEPressure DropBased on 3/4” and 1” inlet/outlet housings, without cartridges.A DCFSSS-1BTopviewCapKnife-edge seal to prevent by-pass.Double O-ring seal.Ordering InformationSpecificationsHARMSCO EUROPE SRL® Via Salvo D’Acquisto 10a-12 46040 Guidizzolo (MN) ItaliaTel: (0039) 0376 818782 • Fax: (0039) 0376 818399 • E-mail: info@harmscoeurope.com© Harmsco, Inc. 12A 3/11www.harmscoeurope.comNote: This publication is to be used as a guide. The data within has been obtained from many sources and is considered to be accurate. Harmsco does not assume liability for the accuracy and/orcompleteness of this data. Changes to the data can be made without notification. Temperature, Pressure, Flow Rates, Differential Pressures, Chemical Combinations and other unknown factors can affect performance in unknown ways. Limited Warranty: Harmsco warrants their products to be free of material and workmanship defects. Determination of suitability of Harmsco products for uses and applications contemplated by Buyer shall be the sole responsibility of Buyer. The end user/installer/buyer shall be liable for the product’s performance and suitability regarding their specific intended applications. End users should perform their own tests to determine suitability for each application.