High Temperature Pumps P46HT

Triplex CeramicPlunger PumpOperating Instructions/Repair and ServiceManualModelsP46W, P46W-HK & P46HTContents:Installation Instructions: page 2Pump Specifications: page 3-4Kits/Torque Specs: page 5Pump Mounting Selection Guide: page 5Exploded View: page 6Parts List: page 7Trouble Shooting: page 8Recommended Spare Parts List: page 8Repair Instructions: page 9-11Dimensions: back pageWarranty Information: back pageUpdated 9/092INSTALLATION INSTRUCTIONS - P46W, P46W-HK, & P46HT4. Use of a dampener is necessary to minimizepulsation at drive elements, plumbing, connec-tions, and other system areas. The use of adampener with Giant Industries, Inc. pumps isoptional, although recommended by GiantIndustries, Inc. to further reduce system pulsa-tion. Dampeners can also reduce the severity ofpressure spikes that occur in systems using ashut-off gun. A dampener must be positioneddownstream from the unloader.5. Crankshaft rotation on Giant Industries, Inc.pumps should be made in the direction desig-nated by the arrows on the pump crankcase.Reverse rotation may be safely achieved byfollowing a few guidelines available upon requestfrom Giant Industries, Inc. Required horsepowerfor system operation can be obtained from thecharts on pages 3-4. The open end shaft mustbe covered by the shaft protector (17).6. Before beginning operation of your pumpingsystem, remember: Check that the crankcaseand seal areas have been properly lubricated perrecommended schedules. Do not run the pumpdry for extended periods of time. Cavitation willresult in severe damage. Always remember tocheck that all plumbing valves are open and thatpumped media can flow freely to the inlet of thepump.Installation of the Giant Industries, Inc., pumpis not a complicated procedure, but there aresome basic steps common to all pumps. Thefollowing information is to be considered as ageneral outline for installation. If you haveunique requirements, please contact GiantIndustries, Inc. or your local distributor forassistance.1. The pump should be installed flat on a base toa maximum of a 15 degree angle of inclination toensure optimum lubrication.2. The inlet to the pump should be sized for theflow rate of the pump with no unnecessaryrestrictions that can cause cavitation. Teflon tapeshould be used to seal all joints. If pumps are tobe operated at temperatures in excess of 1600F(P46W), 195oF (P46W-HK), or 220oF (P46HT) it isimportant to insure a positive head to the pump toprevent cavitation. See NPSHR curve for P46HTon page 4.3. The discharge plumbing from the pump shouldbe properly sized to the flow rate to prevent linepressure loss to the work area. It is essential toprovide a safety bypass valve between the pumpand the work area to protect the pump frompressure spikes in the event of a blockage or theuse of a shut-off gun.Finally, remember that high pressure operation in a pump system has many advantages. But, ifit is used carelessly and without regard to its potential hazard, it can cause serious injury.IMPORTANT OPERATING CONDITIONSFailure to comply with any of theseconditions invalidates the warranty.1. Prior to initial operation, add oil to the crank-case so that oil level is between the two lines onthe oil dipstick. DO NOT OVERFILL.Use Giant Oil # 01154 or the equivalent SAE 80W - 90 Industrial Gear OilCrankcase oil should be changed after the first50 hours of operation, then at regular intervals of500 hours or less depending on operating condi-tions.2. Pump operation must not exceed ratedpressure, volume, or RPM. A pressurerelief device must be installed in the dis-charge of the system.3. Acids, alkalines, or abrasive fluidscannot be pumped unless approval in writingis obtained before operation from GiantIndustries, Inc.4. Run the pump dry approximately 10seconds to drain the water before exposureto freezing temperatures.3Volume............................................................................. Up to 3.9 GPM ............... 14.7 L/MDischarge Pressure ......................................................... 2200 PSI ........................ 150 barInlet Pressure ................................................................... -4.35 to145 psi ................ -0.3 to 10 barMaximum Crankshaft Rotation Speed ....................................................................... Up to 1420 RPMStroke .............................................................................. 0.56” .............................. 14.1mmCrankcase Oil Capacity ................................................... 8 fl.oz. ............................ 0.24 LitersTemperature of Pumped Fluids ......................................... Up to 160oF .................... 71°C (P46W)........................................................................................ Up to 195°F .................... 90°C (P46-HK)Plunger Diameter .............................................................. 0.71” .............................. 18mmInlet Ports ................................................................................................................. (2) 1/2" BSPDischarge Ports ....................................................................................................... (2) 3/8" BSPPulley Mounting ........................................................................................................ Either SideShaft Rotation .......................................................................................... Top of pulley towards headWeight .............................................................................. 13.9 lbs .......................... 6.3 kgCrankshaft Diameter ........................................................ 0.71” .............................. 18mmVolumetric Efficiency @ 1420RPM ........................................................................... 0.96Mechanical Efficiency @ 1420RPM .......................................................................... 0.80Consult the factory for special requirements that must be met if thepump is to operate beyond one or more of the limits specified above.PULLEY INFORMATIONPulley selection and pump speed are based ona 1725 RPM motor and "B" section belts.When selecting desired GPM, allow for a ±5%tolerance on pumps output due to variations inpulleys, belts and motors among manufactur-ers.1. Select GPM required, then select appro-priate motor and pump pulley from the sameline.2. The desired pressure is achieved by se-lecting the correct nozzle size that correspondswith the pump GPM.HORSEPOWER INFORMATIONThe ratings shown in the chart reflect the horse-power requirements for electric motors. Werecommend motors with a 1.15 service factor bespecified.To compute specific pump horsepower require-ments, use the following formula:(GPM X PSI) / 1450 = HPSpecificationsModel P46W/P46W-HKPUMP PULLEYMOTOR PULLEYRPM GPM 1000 PSI 1500 PSI 1700 PSI 2200 PSI7.75" 3.55" 745 2.0 1.4 2.1 2.3 3.07.75" 4.25" 910 2.5 1.7 2.6 2.9 3.87.75" 5.25" 1140 3.1 2.1 3.2 3.6 4.77.75" 5.95" 1305 3.6 2.5 3.7 4.2 5.47.75" 6.45" 1420 3.9 2.7 4.0 4.5 5.9P46W / P46W-HK PULLEY SELECTION & HORSEPOWER REQUIREMENTS - ELECTRIC MOTORU.S. Metric4 U.S. ...................................... MetricVolume................................................................................147.3 GPH (2.5 GPM) ........... 557.5 L/H (9.3 L/M)Discharge Pressure....................................................................... 900 PSI ................................. 60 barInlet Pressure .............................................................................................................. See NPSHR curve belowMaximum Crankshaft Rotation Speed ............................................................................................ 900 RPMStroke.......................................................................................... .056” ...................................... 14.1mmPlunger Diameter ........................................................................... .071” ...................................... 18mmCrankcase Capacity ....................................................................... 8 fl. oz. .................................. 0.24 LitersTemperature .................................................................................. Up to 221oF ............................ 105° CInlet Ports ..................................................................................................................................... (2) 1/2” BSPDischarge Ports ............................................................................................................................ (2) 3/8” BSPPulley Mounting ............................................................................................................................ Either SideShaft Rotation ................................................................................ ...........................Top of pulley towards headWeight ........................................................................................... 13.9 lbs............ ..................... 6.3kgCrankshaft Diameter ...................................................................... .71” ........................................ 18mmConsult the factory for special requirements that must be met if thepump is to operate beyond one or more of the limits specified above.PULLEY INFORMATIONPulley selection and pump speed are based on a 1725RPM motor and "B" section belts. When selectingdesired GPM, allow for a ±5% tolerance on pumpsoutput due to variations in pulleys, belts and motorsamong manufacturers.1. Select GPM required, then select appropriate motorand pump pulley from the same line.2. The desired pressure is achieved by selecting thecorrect nozzle size that corresponds with the pumpGPM.HORSEPOWER INFORMATIONThe ratings shown in the chart reflect the horsepowerrequirements for electric motors. We recommendmotors with a 1.15 service factor be specified.To compute specific pump horsepower requirements,use the following formula:(GPM X PSI) / 1450 = HPSpecificationsModel P46HTNPSHR(FT-HEAD) Viscosity = 1 CentipoiseRPMPUMP PULLEYMOTOR PULLEYRPM GPM GPH 200 PSI 400 PSI 600 PSI 900 PSI7.75" 2.0" 385 1.05 62.9 0.14 0.29 0.43 0.657.75" 3.25" 676 1.8 110.6 0.25 0.50 0.74 1.127.75" 4.25" 900 2.5 147.3 0.34 0.69 1.03 1.55P46HT PULLEY SELECTION & HORSEPOWER REQUIREMENTS - ELECTRIC MOTORNPSHR Chart5Ceramic Plunger Assembly Kit#09539Item Part # Description Qty.24A 07021 Ceramic Plunger 324B 08456 Tension Screw 324C 07676 Copper Ring 325 06648/13333* Flinger 3* p/n 13333 is needed for older P46W pumps withbrass retainers (p/n 08064).P46W, P46W-HK & P46HT REPAIR KITSPlunger Packing Kit, P46W#09038Item Part # Description Qty.31 07241 V-Sleeve 340 07234 O-Ring 3Position Item# Description Torque Amount24B 08456 Tension Screw, Plunger 105 in-lbs.41 07235 Plug, Manifold (Inlet) 52 ft.-lbs.43 07034 Plug, Manifold (Outlet) 52 ft.-lbs46 08040 Hex Nut, Manifold Stud 35 ft.-lbsP46W, P46W-HK & P46HT TORQUE SPECIFICATIONSComplete Plunger Packing Kit, P46W#09081Item Part # Description Qty.31 07241 V-Sleeve 340 07234 O-Ring 350 07239 Rear V-Sleeve 351 07240 Support Ring 3Valve Assembly Kit, P46HT#09497(One Kit Each for Inlet or Discharge Valves)Item Part # Description Qty.34 05593 Spring Retainer 335 06017-0100 Valve Spring 336 06016 Valve Plate 337 06014 Valve Seat 338 06015 O-Ring 340 07234 O-Ring, Adaptor 342 12004 O-Ring, Inlet Plug 344 07035 O-Ring, Discharge Plug 3Plunger Packing Kit, P46W-HK, P46HT#09514Item Part # Description Qty.31 11511 Sleeve 340 07234 O-Ring, Adapter 350 11512 High Temp. Rear Seal 651 07240 Support Ring 3Valve Assembly Kit P46W & P46W-HK#09039(One Kit Each for Inlet or Discharge Valves)Item Part # Description Qty.34 07325 Spring Retainer 335 06017-0100 Valve Spring 336 06016 Valve Plate 337 06014 Valve Seat 338 06015 O-Ring, Valve Seat 340 07234 O-Ring, Adapter 342 12004 O-Ring, Inlet Plug 344 07035 O-Ring, Discharge Plug 3Pump Mounting Selection GuideBushings01065 - 18 mm Tapered H BushingPulley & Sheaves01061 - 7.75” Cast Iron 1 gr. - AB Section01062 - 7.75” Cast Iron - 2 gr. - AB Section01066 - 18 mm - 8” Steel Pulley - 1 gr.Rails01034 - Steel Box Rails(L=9.25” x W=1.18” x H=1.62”)01075 - Plated Steel Channel Rails(L=9.00” x W=2.12” x H=2.50”)6Exploded View - P46W, P46W-HK, P46HT7P46W, P46W-HK & P46HT PARTS LISTITEM PART DESCRIPTION QTY.1 07222 Crankcase 12 07181 Vent/Filler Plug with Seal 13 08004 Cover, Crankcase 14 08005 O-Ring 15 08008 Oil Dipstick 16 01009 O-Ring 19 07188 Cylinder Screw with Slot 410 07223-0100 Spring Washer 411 08012 Oil Drain Plug with Seal 111A 06709 Gasket, Oil Drain Plug 112 07224 Bearing Cover 214 08015 Radial Shaft Seal 215 08020 Ball Bearing 216 07225 Screw and Washer 617 07226 Shaft Protector 118 07227 Crankshaft 119 01024 Key 120 08024 Connecting Rod 322 07201 Crosshead Assy. 323 01031 Crosshead Pin 324A 07021 Plunger Pipe 324B 08456 Tension Screw 324C 07676 Copper Ring 325* 06648 Flinger 326 07206 Radial Shaft Seal 326A 11510 Spacer Sleeve 328 07207 Shim, Manifold Stud 229 07033 Manifold 129A 06176 Stud Bolt (P46HT only) 230 07230 Pressure Ring 3ITEM PART DESCRIPTION QTY.31 07241 V-Sleeve (P46W only) 331 11511 V-Sleeve, High Temp.(P46W-HK, P46HT) 332 07231 Support Ring 333 07232 Pressure Spring 334 07325 Retainer, Spring 6(P46W, P46W-HK)34 05593 Retainer, Spring (P46HT) 635 06017-0100 Valve Spring 636 06016 Valve Plate 637 06014 Valve Seat 638 06015 O-Ring 639 07233 Suction Valve Adaptor 340 07234 O-Ring, Adapter 341 07235 Plug, Manifold (Inlet) 342 12004 O-Ring, for Item 41 343 07792 Plug, Manifold (Discharge) 344 07035 O-Ring for Item 43 345 07215 Stud, Manifold 246 08040 Hex Nut, Manifold Stud 247 08041 Spring Washer, Stud 248 07237 Housing, Rear V-Sleeve 149 07238 O-Ring, Rear V-SleeveHousing 150 07239 Rear V-Sleeve (P46W only) 350 11512 High Temperature Seal(P46W-HK & P46HT) 651 07240 Support Ring, Rear V-Sleeve 352 07109 Plug, 1/2" BSP 153 13338 Plug, 3/8" BSP 1* This will not fit into older P46W pumps with brass retainers (#08064). It can only be used with part number11510 (#26A). You can substitute p/n 13333 for 06648 only if the brass retainer (#08064) is used.PUMP SYSTEM MALFUNCTIONMALFUNCTION CAUSE REMEDYThe Pressure and/ Worn packing seals Replace packing sealsor the Delivery Broken valve spring Replace springDrops Belt slippage Tighten or Replace beltWorn or Damaged nozzle Replace nozzleFouled discharge valve Clean valve assemblyFouled inlet strainer Clean strainerWorn or Damaged hose Repair/Replace hoseWorn or Plugged relief valve on pump Clean, Reset, and Replace worn partsCavitation Check suction lines on inlet ofpump for restrictionsUnloader Check for proper operationWater in crankcase High humidity Reduce oil change intervalWorn seals Replace sealsNoisy Operation Worn bearings Replace bearings, Refill crankcaseoil with recommended lubricantCavitation Check inlet lines for restrictionsand/or proper sizingRough/Pulsating Worn packing Replace packingOperation with Inlet restriction Check system for stoppage, airPressure Drop leaks, correctly sized inletplumbing to pumpAccumulator pressure Recharge/Replace accumulatorUnloader Check for proper operationCavitation Check inlet lines for restrictionsand/or proper sizePump Pressure as Restricted discharge plumbing Re-size discharge plumbing toRated, Pressure flow rate of pumpDrop at gunExcessive Worn plungers Replace plungersLeakage Worn packing/seals Adjust or Replace packing sealsExcessive vacuum Reduce suction vacuumCracked plungers Replace plungersInlet pressure too high Reduce inlet pressureHigh Crankcase Wrong Grade of oil Giant oil is recommendedTemperature Improper amount of oil in crankcase Adjust oil level to proper amountPreventative Maintenance Check-List & Recommended Spare Parts ListCheck Daily Weekly 50hrs Every Every Every500 hrs 1500 hrs 3000 hrsOil Level/Quality XOil Leaks XWater Leaks XBelts, Pulley XPlumbing XRecommended Spare PartsOil Change (8 oz.) p/n 1154 X XPlunger Packing Kits (1 kit/pump) X(See page 5 for kit list)Valve Assembly Kit (1 kit/pump) X(See page 5 for kit list)Oil Seal Kit (1 kit/pump) X(See page 5 for kit list)891. With a 22mm socket, removethe three discharge (43) andthree inlet (41) manifoldplugs. Check o-rings (42 &44) for wear and replace asnecessary.3. Use a small slide hammer toremove valve seats (37) frommanifold (29). Inspect valveplates (36) and valve seats(37) for wear. If excessivepitting is seen, replace theworn parts. Check valve seato-ring (38) for wear andreplace as necessary.2. Remove the discharge springretainer (34), valve spring(35), and valve plate (36).4. Drain the oil from the pump.Turn the pump over toremove the two manifold studnuts (46) with a 17mmwrench.7. Inspect and clean the valve assembly parts. If pitted or worn, replaceinlet valve seats (37), valve plates (36), spring (35) and spring retainers(34). Reinsert items 34-38 into valve adapter (39).5. Tap the back of the manifold(29) with a rubber mallet todislodge, and slide off thepump.6. From the front inlet valveports, remove the inlet valveassembly (34-40).NOTE: Contact Giant Industries for Service School Information. Phone: (419)-531-4600REPAIR INSTRUCTIONS - P46W, P46W-HK, P46HT34 35 36 40 37 39109. The rear V-sleeve housing(48) may be removed byprying evenly outward with aflat screwdriver. After slippinghousing over plunger, inspectrear v-sleeves (50), supportrings (51) and O-ring (49) andreplace as necessary.10.Inspect ceramic plunger(24A) tips for wear. Ifnecessary, replacement ofthe ceramic plungers may beaccomplished by removingthe plunger bolt assemblies(24B and 24C) with a 13mmwrench. Ceramic plungersshould now slide off thestainless steel plunger base(22). Excessive resistanceto plunger removal may beovercome by heating thestainless steel plunger base.This will melt any excessloc-tite beneath the ceramicplunger allowing easyremoval.NOTE: Contact Giant Industries for Service School Information. Phone: (419)-531-4600REPAIR INSTRUCTIONS - P46W, P46W-HK, & P46HT8. The pressure rings (item 30) can now be removed by pulling straightout. Inspect and clean manifold (29) and pressure ring. Replace ifnecessary. From the front of the pump reinstall pressure rings intomanifold (29) with grooved side towards front of manifold. Install newv-sleeves (31), with grooved sides towards front of pump. For P46W-HK & P46HT pumps, install high temperature seal (50) before v-sleeve(31) with grooved sides towards front of pump. Replace the supportrings (32) and pressure springs (33) into manifold (29). Install valveassembly (34-40) into manifold (29). Reinstall manifold plugs (43) andtorque plugs to 52 ft.-lbs.30 50 31 32 38 33(P46W-HK & P46HT only)49505111.Replace copper ring (24C)onto plunger bolt (24B).Slide plunger bolt assemblyinto ceramic plunger (24A).Apply a light film of loc-tite toplunger bolt threads andplace plunger assembly ontostainless steel plunger base(22) and tighten to 105 in.-lbs.12.To replace plunger oil seals(26), proceed to “Gear EndDisassembly” section below.Otherwise, continue asdescribed below.24C13.Before replacing pump manifold(29), first rotate crankshaft (18)until two outside plungers (24A)extend evenly forward. Nextlubricate rear v-sleeves (50)and support ring (51) in the rearv-sleeve housing (48) and slidehousing over plungers. Lubri-cate ceramic plungers with alight film of oil. Carefully andevenly slide manifold overplungers and press manifoldfirmly against crankcase (1).Replace manifold stud bolts(45), washers (47) and nut (46)and tighten to 35 ft.-lbs.11Gear End Disassembly14. Remove the crankcase cover bolts (9). Inspect the crankcase cover O-ring (4) for wear. Replace if neces-sary.15. Inspect the dip stick (5) vent hole for signs of clogging. Clean if necessary.16. To remove the crankshaft (18), first remove the bearing cover plates (12) Remove the key (19).17. Hold the pump rear assembly with a wooden fixture, or other suitable device, in order to secure it whileremoving the crankshaft (18). Using a plastic mallet, tap the crankshaft (18) from one side while turning itfrom the other side. The turning insures that during this sequence the crankshaft does not become wedgedagainst the connecting rods (20). The far side bearing (15) will remain in the crankcase (1). When free, thecrankshaft (18) can be removed by hand.18. The crankshaft bearing (15) remains on the crankshaft (18) as it is removed. The near side crankshaft seal(14) will be removed by this procedure.19. If necessary, use a bearing puller to remove crankshaft bearing (15).20. Remove the connecting rod (20) and plunger rod/crosshead assembly (22) from the rear of the pump bypulling straight out of the crosshead guides.21. To remove the crankcase oil seal (26), tap oil seal out from the rear of the crankcase using a dowel andrubber mallet. The area onto which the oil seal rests should be clean and dry. Put a small drop of loc-tite onthe oil seals and place into crankcase with clips facing the rear of the pump.22. To remove the crosshead pin (23) from the crosshead (22), the assembly should be positioned on awooden fixture to avoid damage to crosshead. Drive out pin (23) on opposite side of mark on the cross-head. On those pumps without mark on crosshead, drive out pin by tapping on tapered side of pin.23. To remove the bearing remaining in the crankcase, insert small end of Giant Bearing tool and tap with arubber mallet untill bearing and seal are completely removed. The bearing can only be removed from theinside by inserting the Giant Bearing Tool through the opposite side of the crankcase (1) and should beinspected for possible damage.Gear End Reassembly24. To reassemble, place the far bearing in the crankcase bearing housing and with the Giant Bearing tool as adriver, tap into the crankcase (1) using a rubber mallet.25. Insert the far side crankshaft oil seal (14) with the Giant Bearing Tool making sure it is firmly seated andwell oiled. Always make sure that the crankshaft seal (14) lip does not show signs of wear. Replace thebearing cover (12) and tighten securely.26. Replace the connecting rod (20) and plunger rod/crosshead assembly (22) by press-fitting the crossheadpin (23). Make sure to insert the beveled edge of the crosshead pin into crosshead. If the crosshead has amark, install pin from marked side. The crosshead pin (23) should not extend beyond either side of thecrosshead in order to prevent damage to the crosshead bore of the crankcase.27. Place each crosshead/plunger assembly (22) into the pump making sure that all of the parts are well oiledbefore insertion into the crankcase.28. Replace near side bearing on crankshaft (18) and use mallet to tap into place.29. Take the crankshaft (18) end with the bearing and insert the other end through the bearing housing carefullythreading the lobes of the crankshaft through the well lubricated connecting rods (20). Turning the crank-shaft while tapping it through the connecting rods will help prevent binding and possible damage to theconnecting rods. Continue tapping the crankshaft through the connecting rods (20) until it is firmly seatedinto far side bearing.30. Insert the near side crankshaft oil seal (14), making sure it is firmly seated and well oiled. Replace thebearing cover (12) and tighten securely.31. See instructions (13 above) for re-installing fluid end onto gear end.REPAIR INSTRUCTIONS - P46W, P46W-HK, & P46HTGiant Industries, Inc.900 N. Westwood Ave.Toledo, OH 43607419-531-4600419-531-6836 Faxwww.giantpumps.comGIANT INDUSTRIES LIMITED WARRANTYGiant Industries, Inc. pumps and accessories are warranted by the manufacturer to be free fromdefects in workmanship and material as follows:1. For portable pressure washers and car wash applications, the discharge manifolds willnever fail, period. If they ever fail, we will replace them free of charge. Our other pumpparts, used in portable pressure washers and in car wash applications, are warrantedfor five years from the date of shipment for all pumps used in NON-SALINE, cleanwater applications.2. One (1) year from the date of shipment for all other Giant industrial and consumerpumps.3. Six (6) months from the date of shipment for all rebuilt pumps.4. Ninety (90) days from the date of shipment for all Giant accessories.This warranty is limited to repair or replacement of pumps and accessories of which the manufacturer’sevaluation shows were defective at the time of shipment by the manufacturer. The following itemsare NOT covered or will void the warranty:1. Defects caused by negligence or fault of the buyer or third party.2. Normal wear and tear to standard wear parts.3. Use of repair parts other than those manufactured or authorized by Giant.4. Improper use of the product as a component part.5. Changes or modifications made by the customer or third party.6. The operation of pumps and or accessories exceeding the specifications set forthin the Operations Manuals provided by Giant Industries, Inc.Liability under this warranty is on all non-wear parts and limited to the replacement or repair of thoseproducts returned freight prepaid to Giant Industries which are deemed to be defective due toworkmanship or failure of material. A Returned Goods Authorization (R.G.A.) number and completedwarranty evaluation form is required prior to the return to Giant Industries of all products underwarranty consideration. Call (419)-531-4600 or fax (419)-531-6836 to obtain an R.G.A. number.Repair or replacement of defective products as provided is the sole and exclusive remedy providedhereunder and the MANUFACTURER SHALL NOT BE LIABLE FOR FURTHER LOSS, DAMAGES,OR EXPENSES, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES DIRECTLY ORINDIRECTLY ARISING FROM THE SALE OR USE OF THIS PRODUCT.THE LIMITED WARRANTY SET FORTH HEREIN IS IN LIEU OF ALL OTHER WARRANTIES ORREPRESENTATION, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRAN-TIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ALL SUCHWARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED BY THE MANUFACTURER. © 2009 Giant Industries, Inc. 9/09 P46W, P46W-HK, & P46HT.PMDP46W, P46W-HK & P46HT DIMENSIONS - Inches