Hydro Safe Premium VG-32, 46, 68 pdf

Hydro Safe 13626 Pearwood Drive DeWitt, Michigan 48820 Voice: 800-500-5028 Fax: 517-669-1207 www.hydrosafe.com Availability F.O.B. :Hartville, Ohio, USA 5 Gallon Pails Drums Bulk Hydro Safe® Premium Hydraulic Fluids (ISO VG-32, 46, 68) "Biobased Lubricants that Perform Like Synthetics" Hydro Safe Premium Hydraulic Fluids are ultimately biodegradable1 vegetable based formulas that replace mineral oil based hydraulic fluids. Hydro Safe Premium Hydraulic Fluids are formulated to perform in hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-foam, and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass both A and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index of the Stabilized* High Oleic Base Stocks (HOBS) into the formula, increases the viscosity index past synthetic levels (Energy Conserving Formulas). Zinc-free additive systems have also been developed that are environmentally friendly and meet or exceed pump requirements. Hydro Safe Premium Hydraulic Fluids are designed for use in mobile and stationary hydraulic vane, piston, and gear-type pumps and have shown to have exceptional anti-wear performance. Very little wear was encountered, 0 to 25mg (Pass), in accelerated biobased tests using Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882), Vickers I-286-S, pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 1500 to 2100 F. The anti-wear performance exceeds the requirements for US Steel 126 and 127, load stage 10 in the FZG (DIN 51354), DIN 51524, and GM (LS-2). They also meet the requirements for ashless GL-3 gear oils in reduction units and gear sets where they meet the viscosity ranges. Hydro Safe meets and exceeds Federal Specifications A-A-59354 Superseding MIL-H-46001D. The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and increases load capacity. The HOBS’s extremely low volatility increases the flash and fire safety features in the formula. They are formulated to provide seal conditioning for longer seal life and to reduce oil leakage from the system. Hydro Safe Premium Hydraulic Fluids should be used in hydraulic systems where low toxicity, and BIODEGRADABILITY properties are required. Base oils and additives in these products pass and exceed the acute toxicity (LC-50) criteria adopted by the US Fish and Wildlife Service and the US EPA. Hydro Safe Premium Hydraulic Fluids are ENVIRONMENTALLY RESPONSIBLE lubricants that are formulated from renewable agricultural plant resources. We believe Earth's environmental future rests in the use of renewable materials. STABILIZED by Hydro Safe®* is Hydro Safe’s trademark on their proprietary and patented anti-oxidant, anti-wear, and cold flow technology. High Oleic Base Stock (HOBS) are agricultural vegetable oils. This Stabilized technology allows the HOBS to perform as a high performance formula in high and low temperature applications, reducing oil thickening and deposits. 1 Ultimate Biodegradation (Pw1) within 28 days in ASTM D-5864 Aerobic Aquatic Biodegradation of Lubricants Patented Product: US Patent 6,383,992, US Patent 6,534,454 with additional Pending and Foreign Patents * Trademark of Hydro Safe® Copyright 1999 Hydro Safe® Hydro Safe® Premium Hydraulic Fluids ISO 32, 46, 68 The test data below show that the Hydro Safe® Premium Hydraulic Fluids provide high performance in a wide variety of stationary and transportation equipment that operate in broad ranges of environmental conditions. In equipment operating outside, wear from poor cold temperature pumpability, surge loads, moisture, and dusty environments are more prominent. Hydro Safe Premium Hydraulic Fluids are formulated to improve performance in equipment that requires excellent anti-wear, hydrolytic stability, and cold temperature pumpability as low as -350C. In addition, the products may be used in machine tool hydraulic systems with the above Denison and Vickers pump requirements and exceeds the requirements of US Steel 126, 127 and DIN 51524 Part 2. TYPICAL SPECIFICATIONS METHOD ISO 32 ISO 46 ISO 68 Spec. Requirements Specific Gravity @ 15.6°C Viscosity @ 40°C Viscosity @ 100°C Viscosity @ -15°C, Brookfield Viscosity @ -25°C, Brookfield Viscosity @ -30°C MRV TP1 Viscosity @ -35°C MRV TP1 Viscosity Index ASTM D-287 ASTM D-445 ASTM D-445 ASTM D-2983 ASTM D-2983 ASTM D-4684 ASTM D-4684 ASTM D-2270 0.88 30.87 6.9 550 cP 1,200 cP 4,500 cP 7,500 cP 184 0.88 43.8 9.67 1100 cP 3,000 cP 8000 cP 11,000 cP 199 0.88 64.1 12.5 3200cP 4500 cP 15,000 cP 24,000 cP 198 Report Note 1 Note 1 Note 1 Note 1 10W= <60,000 5W= <60,000 90 (min) Pour Point Flash Point (COC) Fire Point (COC) Hydrolytic Stability, Copper Wt. Loss (mg) Copper Appearance Change in Acid Number Water Layer % Insolubles Foam Sequence I, II, III (10 min) Rust Prevention Distilled Water Syn. Sea Water ASTM D-97 ASTM D-92 ASTM D-92 ASTM D-2619 ASTM D-892 ASTM D-665 -40°C 236°C 260°C 0.0139 1B 0.16 3.0 0.001 0 Foam Pass Pass -40°C 243°C 268°C 0.0208 1B 0.20 3.0 0.001 0 Foam Pass Pass -39°C 251°C 274°C 0.0208 1B 0.21 3.0 0.001 0 Foam Pass Pass Note 1 198°C (min) 218°C (min) 0.2 Report Report 4 Report 0 Foam Pass Pass Copper Corrosion Strip 3hr @ 100°C ASTM D-130 1B 1B 1B DIN 51524 2(max) Rotary Bomb Oxidation, (minutes) Oxidation Stability (Pressure Differential Scanning Calorimeter) min Neutralization Number mg KOH/g Swell of Synthetic NBR-L Rubber, % (Avg.) Volume Change (%) Shore A Hardness Change (%) Filterability A-No Water (s) (Avg) B-2% Water (s) (Avg) Demulsibility, ML Oil/Water/Emulsion 4-Ball Wear, 1h, 167°F, 1200 RPM, 40 kg FZG Test ASTM D-2272 ASTM D-5483 Modified ASTM D-974 DIN 53538, Part 1 Denison TP 02100 HF-0 Requirement ASTM D-1401 ASTM D-4172 DIN 51354 360 70.0 (165°C) <0.4 6.0 -4 113 187 40/ 40/ 0 (10 minutes) 0.3 – 0.4 12 360 70.0 (165°C) <0.4 6.0 -4 268 271 40/ 40/ 0 (10 minutes) 0.3 – 0.4 12 360 70.0 (165°C) <0.4 6.0 -4 335 449 40/ 40/ 0 (10 minutes) 0.3 – 0.4 12 USS 120 (min) Note 2 1.5 (max) 0 to 12 0 to -7 600 (max) 2xA (max) 40/37/3 (max) (30 minutes) USS 127 0.5 (max) US.Steel 10 (min) Biodegradation Classification Environmentally Friendly USDA Biobased Tested Environmental Management System Note 1 Viscosity Sufficient for Application Note 2 Not Required ASTM D-5864 ISO 15380 New Carbon ISO 14001:1996 Ultimate PW1 yes yes yes 81000 Ultimate PW1 yes yes yes 81010 Ultimate PW1 yes yes yes 81020 Ultimate PW1 meets/exceeds over 50%