JPES - Portable Sampling Probe Brochure

? Sampling Conditioning Systems ? Process Analytics ? System Integration ? Gas Generators ? FTIR-Analysers APPLICATION The heated JPES sample probe is designed for use in extractive sampling systems with sample gases containing dust and aerosol, especially for measure-ment in not stationary applications. The heated gas sample probe JPES and the also included heated sample hose ensure that water va-pour and high dew point corrosive gases are kept above their dew point to prevent corrosion and sam-ple degradation prior to the analysis or sample condi-tioning. All necessary parts for a mobile gas sample probe are part of the package and placed in a handy case. Quick On connectors allow tool-less mounting and operation. Filter replacement as well can be done easily without any tools and without disconnecting the heated sample line. Different pipes -heated and unheated-, materials and filters as well as heated hoses make the JPES very flexible for different applications. TECHNOLOGY The JPES sample probe can be equipped with sev-eral different replaceable, heated and large surface filter elements. The filter element is mounted in a thermal isolated and electrically heated stainless steel housing covered by a protection enclosure. The temperature regulation is done by a maintenance free PTC heater. OPERATION The probe is mounted directly to a sampling hole or flange. If the assembly takes place horizontal, the JPES should be built in an angle at least between 5° and 15° from the horizontals falling, to allow conden-sate flow back into the process. The heated sample line JH-SO 9412 series is directly connected with the probes housing via a Quick On connection. The sampling is ready for use within a few minutes. FEATURES ? All-in-one ? Compact and light weight ? Easy site set up ? Quick On connectors ? Quick heat up ? Zero cold spot technology ? Integrated temperature controller ? Versatile accessories Conditioning systems Portable Sampling Probe JPES and Heated Hose Page 1 TECHNICAL DATA SPECIFICATIONS OF SAMPLING PROBE Filter element GF, PTFE, SS Operating pressure 50 kPa abs. Flow rate Up to 200 l/h depending on filter element Mounting flange Flange adapter universal 20-80mm Mounting angle 5°-15° sloping down Sample gas connector Quick On Heated hose connection Quick On Calibration gas connec-tor Quick On Sample gas wetted parts 1.4571, Viton Operating temperature nom. Operating tempera-ture max. 180°C 200°C Heat up time <15 min Permissible ambient temperature -20°C ... +55°C Power consumption Approx. 160 W Heater element PTC self limiting Supply voltage 115VAC or 230VAC/ 50/60Hz Inrush current 3 A Status signal Volt free contact Protection class IP 22 Weight 3,1 kg SPECIFICATIONS OF HEATED SAMPLE PIPE (OPTION) Supply voltage 115VAC or 230VAC/50/60Hz Power consumption approx. 150 W/m Heater Integrated temperature controller Gas wetted parts SS 1.4571 Outer diameter 25mm Nominal width inner-pipe ID4 mm Connector pre filter Thread connector R3/8” Length 1000, 1500, 2000mm Length over all 1110, 1610, 2110mm Weight 1,8;3,0;3,6kg Operating temperature +180°C Sample gas temperature max. 250°C Heat up time < 15min Connector 7-pin Power supply via heated hose On-time 100% Protection class IP54 Page 2 SPECIFICATIONS OF HEATED HOSE Supply voltage 115VAC or 230VAC/50/60Hz Power consumption approx. 100 W/m Heating Integrated temperature controller Shell PA-braided Outer diameter 35mm Minimal bending radius 50mm Colour black Operating temperature 180°C Heat up time < 15 min Fusing External, on site On-time 100% Inner core PTFE Nominal width inner core ID4/ OD6 mm Signal cord 2 x 0,75², open endings Power cord IEC or country specific plug Cable length 2m each ORDER CODES Page 3 Part-No. Components description Content „Starter“ Content „Premium“ 34.00401 Heated hose 230VAC l=3m inside 6x4mm (v) 34.00402 Heated hose 230VAC l=5m inside 6x4mm (v) 34.00403 Heated hose 230VAC l=7m inside 6x4mm 34.00411 Heated hose 115VAC l=3m inside 6x4mm (v) 34.00412 Heated hose 115VAC l=5m inside 6x4mm (v) 34.90015 Filter element microfiber 2µm (PU 5 pcs) 1x v K3411305 Filter element PTFE 2µm 2x K3411310 Filter element SS sieve fabric 2µm, incl. sealing 34.00307 34.00308 34.00309 Sample pipe SS ID8/OD10mm, max. 600°C L= 300mm L= 500mm L=1000mm v v 34.00304 34.00305 34.00306 Sample pipe SS ID6/OD8mm, max. 600°C L= 300mm L= 500mm L=1000mm v 34.00301 34.00302 34.00303 Sample pipe SS ID4/OD6mm, max. 600°C L= 300mm L= 500mm L=1000mm v 34.00610 Heated sample pipe 230VAC l=1m 34.00615 Heated sample pipe 230VAC l=1,5m 34.00620 Heated sample pipe 230VAC l=2m 34.00710 Heated sample pipe 115VAC l=1m 34.00715 Heated sample pipe 115VAC l=1,5m 34.00720 Heated sample pipe 115VAC l=2m 34.00510 Calibration gas connector v 34.90025 Calibration gas tamping v v P3400100 Carrying case yellow with shell moulds v v K1001041 O-ring A (Filter lock inside) Ø15mm K1001043 O-ring B (Filter lock outside) Ø33mm K1001042 O-ring C (Quick on connectors) Ø6mm 34.90010 O-ring set: 1x O-ring A, 1x O-ring B, 4x O-ring C v K3419010 PTFE paste 113,4g collapsible tube v 34.00501 Mounting chain (2x1m) v v 34.00520 Filter lock complete K3419020 Disassembling aid (flat spanner) v v On request Stationary sampling point: sample gas con-nector with ferrule for screw in mounting On request Stationary sampling point: sample port with ferrule welded in mounting K3419030 Mobile sample point adapter universal (cone-shaped for pipe diameter20-60mm) v v Part-No. Components description 34.00150 JPESX Starter Kit, 115V 34.00250 JPES Starter Kit, 230V 34.00180 JPESX Premium Kit, 115V 34.00280 JPES Premium Kit, 230V JCT Analysentechnik GmbH Werner Heisenberg-Straße 4 A-2700 Wiener Neustadt Tel. +43 (0) 2622 / 87201 Fax +43 (0) 2622 / 872011 E-Mail: sales@jct.at Web: www.jct.at Specification subject to change without notice. PDS_E_JPES_v1.4 TECHNICAL DRAWINGS Page 3 Heated sample probe Heated hose Heated sample pipe