Microphone & Preamplifier Systems- Brochure

Model 378A13ICP Microphone SystemInstallation and Operating ManualThis manual contains the 377A13, 426E01 installation and operating manuals thatcomprise a Model 378A13 ICP Microphone System kit.For assistance with the operation of this product,contact PCB Piezotronics, Inc.Toll-free: 800-828-884024-hour SensorLine: 716-684-0001Fax: 716-684-0987E-mail: info@pcb.comWeb: www.pcb.com The information contained in this document supersedes all similar information that may be found elsewhere in this manual. Total Customer Satisfaction – PCB Piezotronics guarantees Total Customer Satisfaction. If, at any time, for any reason, you are not completely satisfied with any PCB product, PCB will repair, replace, or exchange it at no charge. You may also choose to have your purchase price refunded in lieu of the repair, replacement, or exchange of the product. Service – Due to the sophisticated nature of the sensors and associated instrumentation provided by PCB Piezotronics, user servicing or repair is not recommended and, if attempted, may void the factory warranty. Routine maintenance, such as the cleaning of electrical connectors, housings, and mounting surfaces with solutions and techniques that will not harm the physical material of construction, is acceptable. Caution should be observed to insure that liquids are not permitted to migrate into devices that are not hermetically sealed. Such devices should only be wiped with a dampened cloth and never submerged or have liquids poured upon them. Repair – In the event that equipment becomes damaged or ceases to operate, arrangements should be made to return the equipment to PCB Piezotronics for repair. User servicing or repair is not recommended and, if attempted, may void the factory warranty. Calibration – Routine calibration of sensors and associated instrumentation is recommended as this helps build confidence in measurement accuracy and acquired data. Equipment calibration cycles are typically established by the users own quality regimen. When in doubt about a calibration cycle, a good “rule of thumb” is to recalibrate on an annual basis. It is also good practice to recalibrate after exposure to any severe temperature extreme, shock, load, or other environmental influence, or prior to any critical test. PCB Piezotronics maintains an ISO-9001 certified metrology laboratory and offers calibration services, which are accredited by A2LA to ISO/IEC 17025, with full traceablility to N.I.S.T. In addition to the normally supplied calibration, special testing is also available, such as: sensitivity at elevated or cryogenic temperatures, phase response, extended high or low frequency response, extended range, leak testing, hydrostatic pressure testing, and others. For information on standard recalibration services or special testing, contact your local PCB Piezotronics distributor, sales representative, or factory customer service representative. Returning Equipment – Following these procedures will insure that your returned materials are handled in the most expedient manner. Before returning any equipment to PCB Piezotronics, contact your local distributor, sales representative, or factory customer service representative to obtain a Return Warranty, Service, Repair, and Return Policies and Instructions Materials Authorization (RMA) Number. This RMA number should be clearly marked on the outside of all package(s) and on the packing list(s) accompanying the shipment. A detailed account of the nature of the problem(s) being experienced with the equipment should also be included inside the package(s) containing any returned materials. A Purchase Order, included with the returned materials, will expedite the turn-around of serviced equipment. It is recommended to include authorization on the Purchase Order for PCB to proceed with any repairs, as long as they do not exceed 50% of the replacement cost of the returned item(s). PCB will provide a price quotation or replacement recommendation for any item whose repair costs would exceed 50% of replacement cost, or any item that is not economically feasible to repair. For routine calibration services, the Purchase Order should include authorization to proceed and return at current pricing, which can be obtained from a factory customer service representative. Warranty – All equipment and repair services provided by PCB Piezotronics, Inc. are covered by a limited warranty against defective material and workmanship for a period of one year from date of original purchase. Contact PCB for a complete statement of our warranty. Expendable items, such as batteries and mounting hardware, are not covered by warranty. Mechanical damage to equipment due to improper use is not covered by warranty. Electronic circuitry failure caused by the introduction of unregulated or improper excitation power or electrostatic discharge is not covered by warranty. Contact Information – International customers should direct all inquiries to their local distributor or sales office. A complete list of distributors and offices can be found at www.pcb.com. Customers within the United States may contact their local sales representative or a factory customer service representative. A complete list of sales representatives can be found at www.pcb.com. Toll-free telephone numbers for a factory customer service representative, in the division responsible for this product, can be found on the title page at the front of this manual. Our ship to address and general contact numbers are: PCB Piezotronics, Inc. 3425 Walden Ave. Depew, NY 14043 USA Toll-free: (800) 828-8840 24-hour SensorLineSM: (716) 684-0001 Website: www.pcb.com E-mail: info@pcb.com DOCUMENT NUMBER: 21354 DOCUMENT REVISION: B ECN: 17900 1122A AB BCODEIDENT. NO.52681DWG. NO.SCALE: SHEETDRAWN CHECKED ENGINEERTITLEUNLESS OTHERWISE SPECIFIED TOLERANCES ARE:DIMENSIONS IN MILLIMETERS[ IN BRACKETS ]ANGLES ? 2 DEGREES3425 WALDEN AVE. DEPEW, NY 14043(716) 684-0001 E-MAIL: sales@pcb.comDIMENSIONS IN INCHESANGLES ? 2 DEGREESFILLETS AND RADII .003 - .005 FILLETS AND RADII 0.07 - 0.13 OUTLINE DRAWING578321 OF 11.5X1/2" ICP MICROPHONE SYSTEM378A13DECIMALS XX ±.03XXX ±.010DECIMALS X ± 0.8XX ± 0.25JDM 12/20/13 JDM 12/20/13 MT 12/20/13jmorawski 08:17 1/20/201457832PCB Piezotronics Inc. claims proprietary rights inthe information disclosed hereon. Neither it nor anyreproduction thereof will be disclosed to otherswithout the written consent of PCB Piezotronics Inc.REVISIONSREV DESCRIPTION DINNR RELEASED TO DRAFTING 423623.50 [89.0]?.52 [13.2]3.08 [78.2].43 [10.9]BNC CONNECTOR (OUTPUT)?.03 [.8].53 [13.4]426E01 PREAMPLIFIER.50 [12.7]?377A13 MICROPHONE CARTRIDGEModel 377A13Precision Condenser MicrophoneInstallation and Operating ManualFor assistance with the operation of this product,contact PCB Piezotronics, Inc.Toll-free: 800-828-884024-hour SensorLine: 716-684-0001Fax: 716-684-0987E-mail: info@pcb.comWeb: www.pcb.com The information contained in this document supersedes all similar information that may be found elsewhere in this manual. Total Customer Satisfaction – PCB Piezotronics guarantees Total Customer Satisfaction. If, at any time, for any reason, you are not completely satisfied with any PCB product, PCB will repair, replace, or exchange it at no charge. You may also choose to have your purchase price refunded in lieu of the repair, replacement, or exchange of the product. Service – Due to the sophisticated nature of the sensors and associated instrumentation provided by PCB Piezotronics, user servicing or repair is not recommended and, if attempted, may void the factory warranty. Routine maintenance, such as the cleaning of electrical connectors, housings, and mounting surfaces with solutions and techniques that will not harm the physical material of construction, is acceptable. Caution should be observed to insure that liquids are not permitted to migrate into devices that are not hermetically sealed. Such devices should only be wiped with a dampened cloth and never submerged or have liquids poured upon them. Repair – In the event that equipment becomes damaged or ceases to operate, arrangements should be made to return the equipment to PCB Piezotronics for repair. User servicing or repair is not recommended and, if attempted, may void the factory warranty. Calibration – Routine calibration of sensors and associated instrumentation is recommended as this helps build confidence in measurement accuracy and acquired data. Equipment calibration cycles are typically established by the users own quality regimen. When in doubt about a calibration cycle, a good “rule of thumb” is to recalibrate on an annual basis. It is also good practice to recalibrate after exposure to any severe temperature extreme, shock, load, or other environmental influence, or prior to any critical test. PCB Piezotronics maintains an ISO-9001 certified metrology laboratory and offers calibration services, which are accredited by A2LA to ISO/IEC 17025, with full traceablility to N.I.S.T. In addition to the normally supplied calibration, special testing is also available, such as: sensitivity at elevated or cryogenic temperatures, phase response, extended high or low frequency response, extended range, leak testing, hydrostatic pressure testing, and others. For information on standard recalibration services or special testing, contact your local PCB Piezotronics distributor, sales representative, or factory customer service representative. Returning Equipment – Following these procedures will insure that your returned materials are handled in the most expedient manner. Before returning any equipment to PCB Piezotronics, contact your local distributor, sales representative, or factory customer service representative to obtain a Return Warranty, Service, Repair, and Return Policies and Instructions Materials Authorization (RMA) Number. This RMA number should be clearly marked on the outside of all package(s) and on the packing list(s) accompanying the shipment. A detailed account of the nature of the problem(s) being experienced with the equipment should also be included inside the package(s) containing any returned materials. A Purchase Order, included with the returned materials, will expedite the turn-around of serviced equipment. It is recommended to include authorization on the Purchase Order for PCB to proceed with any repairs, as long as they do not exceed 50% of the replacement cost of the returned item(s). PCB will provide a price quotation or replacement recommendation for any item whose repair costs would exceed 50% of replacement cost, or any item that is not economically feasible to repair. For routine calibration services, the Purchase Order should include authorization to proceed and return at current pricing, which can be obtained from a factory customer service representative. Warranty – All equipment and repair services provided by PCB Piezotronics, Inc. are covered by a limited warranty against defective material and workmanship for a period of one year from date of original purchase. Contact PCB for a complete statement of our warranty. Expendable items, such as batteries and mounting hardware, are not covered by warranty. Mechanical damage to equipment due to improper use is not covered by warranty. Electronic circuitry failure caused by the introduction of unregulated or improper excitation power or electrostatic discharge is not covered by warranty. Contact Information – International customers should direct all inquiries to their local distributor or sales office. A complete list of distributors and offices can be found at www.pcb.com. Customers within the United States may contact their local sales representative or a factory customer service representative. A complete list of sales representatives can be found at www.pcb.com. Toll-free telephone numbers for a factory customer service representative, in the division responsible for this product, can be found on the title page at the front of this manual. Our ship to address and general contact numbers are: PCB Piezotronics, Inc. 3425 Walden Ave. Depew, NY 14043 USA Toll-free: (800) 828-8840 24-hour SensorLineSM: (716) 684-0001 Website: www.pcb.com E-mail: info@pcb.com DOCUMENT NUMBER: 21354 DOCUMENT REVISION: B ECN: 17900 Model Number 377A13 PRECISION CONDENSER MICROPHONE Revision: D ECN #: 42896 Performance ENGLISH SI Nominal Microphone Diameter 1/2" 1/2" Frequency Response Characteristic Pressure Pressure Open Circuit Sensitivity 12.6 mV/Pa 12.6 mV/Pa [3] Open Circuit Sensitivity(± 2 dB) -38.0 dB re 1 V/Pa -38.0 dB re 1 V/Pa [3] Frequency Range(± 2 dB) 4 to 20,000 Hz 4 to 20,000 Hz Lower Limiting Frequency(-3 dB) 1.0 to 3.0 Hz 1.0 to 3.0 Hz Resonant Frequency(90° Phase Shift) 18,500 Hz 18,500 Hz [1] Inherent Noise <20 dB(A) re 20 µPa <20 dB(A) re 20 µPa Dynamic Range(3% Distortion Limit) >155 dB re 20 µPa >155 dB re 20 µPa Standards Designation(IEC 61094-4) WS2P WS2P Environmental Temperature Range(Operating) -40 to +248 °F -40 to +120 °C Temperature Coefficient of Sensitivity(+14 to +158°F (-10 to +70°C)) 0.004 dB/°F 0.008 dB/°C [1][3]Static Pressure Coefficient -0.005 dB/kPa -0.005 dB/kPa [1][3]Humidity Coefficient of Sensitivity(0 to 100%, non-condensing) ± 0.001 dB/%RH ± 0.001 dB/%RH [3] Influence of Axial Vibration(0.1g (1 m/s²)) 66 dB re 20 µPa 66 dB re 20 µPa [1] Electrical Capacitance(Polarized) 14 pF 14 pF [1] Polarization Voltage 0 V 0 V [2] Physical Housing Material Stainless Alloy Stainless Alloy Venting Rear Rear Mounting Thread(Preamplifier) 0.4606 - 60 UNS 11.7 mm - 60 UNS Mounting Thread(Grid) 0.5 - 60 UNS 12.7 mm - 60 UNS Size (Diameter x Height)(with grid) 0.52 in x 0.5 in 13.2 mm x 12.7 mm Size (Diameter x Height)(without grid) 0.5 in x 0.47 in 12.7 mm x 11.9 mm Weight 0.23 oz 6.5 gm [1] All specifications are at room temperature unless otherwise specified. In the interest of constant product improvement, we reserve the right to change specifications without notice. ICP® is a registered trademark of PCB Group, Inc. OPTIONAL VERSIONS Optional versions have identical specifications and accessories as listed for the standard model except where noted below. More than one option may be used. NOTES:[1] Typical.[2] Prepolarized[3] re 250 Hz SUPPLIED ACCESSORIES: Model ACS-20 Calibration of Precision Condensor Microphones (1) Entered: AP Engineer: MJN Sales: MV Approved: MT Spec Number: Date: 5/7/2014 Date: 5/7/2014 Date: 5/7/2014 Date: 5/7/2014 37188 3425 Walden Avenue, Depew, NY 14043Phone: 716-684-0001 Fax: 716-684-0987 E-Mail: info@pcb.comCODEIDENT. NO.52681DWG. NO.SCALE: SHEETDRAWN CHECKED ENGINEERTITLEUNLESS OTHERWISE SPECIFIED TOLERANCES ARE:DIMENSIONS IN MILLIMETERS[ IN BRACKETS ]ANGLES ? 2 DEGREES3425 WALDEN AVE. DEPEW, NY 14043(716) 684-0001 E-MAIL: sales@pcb.comDIMENSIONS IN INCHESANGLES ? 2 DEGREESFILLETS AND RADII .003 - .005 FILLETS AND RADII 0.07 - 0.13 OUTLINE DRAWING292881 OF14X1/2" PRE-POLARIZEDMICROPHONESDECIMALS XX ±.03XXX ±.010DECIMALS X ± 0.8XX ± 0.25JDM 9/14/05 ECB 9/14/05 CCL 9/14/05 1122A AB B.60 [15.3].64 [16.4].36 [9.2]?.50 [12.7] .4606-60 UNS[11.7 mm-60 UNS] THREADS.52 [13.2]?.47 [12.0]?.48 [12.1]?.5000-60 UNS[12.7mm-60 UNS] THREADSDIAPHRAGM WITH GRID CAP WITHOUT GRID CAP?.04[1.0]BLACK O-RINGREVISIONSREV DESCRIPTION DINNR RELEASED TO DRAFTING 29288PCB Piezotronics Inc. claims proprietary rights inthe information disclosed hereon. Neither it nor anyreproduction thereof will be disclosed to otherswithout the written consent of PCB Piezotronics Inc.Model 426E01Microphone PreamplifierInstallation and Operating ManualFor assistance with the operation of this product,contact PCB Piezotronics, Inc.Toll-free: 800-828-884024-hour SensorLine: 716-684-0001Fax: 716-684-0987E-mail: info@pcb.comWeb: www.pcb.com The information contained in this document supersedes all similar information that may be found elsewhere in this manual. Total Customer Satisfaction – PCB Piezotronics guarantees Total Customer Satisfaction. If, at any time, for any reason, you are not completely satisfied with any PCB product, PCB will repair, replace, or exchange it at no charge. You may also choose to have your purchase price refunded in lieu of the repair, replacement, or exchange of the product. Service – Due to the sophisticated nature of the sensors and associated instrumentation provided by PCB Piezotronics, user servicing or repair is not recommended and, if attempted, may void the factory warranty. Routine maintenance, such as the cleaning of electrical connectors, housings, and mounting surfaces with solutions and techniques that will not harm the physical material of construction, is acceptable. Caution should be observed to insure that liquids are not permitted to migrate into devices that are not hermetically sealed. Such devices should only be wiped with a dampened cloth and never submerged or have liquids poured upon them. Repair – In the event that equipment becomes damaged or ceases to operate, arrangements should be made to return the equipment to PCB Piezotronics for repair. User servicing or repair is not recommended and, if attempted, may void the factory warranty. Calibration – Routine calibration of sensors and associated instrumentation is recommended as this helps build confidence in measurement accuracy and acquired data. Equipment calibration cycles are typically established by the users own quality regimen. When in doubt about a calibration cycle, a good “rule of thumb” is to recalibrate on an annual basis. It is also good practice to recalibrate after exposure to any severe temperature extreme, shock, load, or other environmental influence, or prior to any critical test. PCB Piezotronics maintains an ISO-9001 certified metrology laboratory and offers calibration services, which are accredited by A2LA to ISO/IEC 17025, with full traceablility to N.I.S.T. In addition to the normally supplied calibration, special testing is also available, such as: sensitivity at elevated or cryogenic temperatures, phase response, extended high or low frequency response, extended range, leak testing, hydrostatic pressure testing, and others. For information on standard recalibration services or special testing, contact your local PCB Piezotronics distributor, sales representative, or factory customer service representative. Returning Equipment – Following these procedures will insure that your returned materials are handled in the most expedient manner. Before returning any equipment to PCB Piezotronics, contact your local distributor, sales representative, or factory customer service representative to obtain a Return Warranty, Service, Repair, and Return Policies and Instructions Materials Authorization (RMA) Number. This RMA number should be clearly marked on the outside of all package(s) and on the packing list(s) accompanying the shipment. A detailed account of the nature of the problem(s) being experienced with the equipment should also be included inside the package(s) containing any returned materials. A Purchase Order, included with the returned materials, will expedite the turn-around of serviced equipment. It is recommended to include authorization on the Purchase Order for PCB to proceed with any repairs, as long as they do not exceed 50% of the replacement cost of the returned item(s). PCB will provide a price quotation or replacement recommendation for any item whose repair costs would exceed 50% of replacement cost, or any item that is not economically feasible to repair. For routine calibration services, the Purchase Order should include authorization to proceed and return at current pricing, which can be obtained from a factory customer service representative. Warranty – All equipment and repair services provided by PCB Piezotronics, Inc. are covered by a limited warranty against defective material and workmanship for a period of one year from date of original purchase. Contact PCB for a complete statement of our warranty. Expendable items, such as batteries and mounting hardware, are not covered by warranty. Mechanical damage to equipment due to improper use is not covered by warranty. Electronic circuitry failure caused by the introduction of unregulated or improper excitation power or electrostatic discharge is not covered by warranty. Contact Information – International customers should direct all inquiries to their local distributor or sales office. A complete list of distributors and offices can be found at www.pcb.com. Customers within the United States may contact their local sales representative or a factory customer service representative. A complete list of sales representatives can be found at www.pcb.com. Toll-free telephone numbers for a factory customer service representative, in the division responsible for this product, can be found on the title page at the front of this manual. Our ship to address and general contact numbers are: PCB Piezotronics, Inc. 3425 Walden Ave. Depew, NY 14043 USA Toll-free: (800) 828-8840 24-hour SensorLineSM: (716) 684-0001 Website: www.pcb.com E-mail: info@pcb.com DOCUMENT NUMBER: 21354 DOCUMENT REVISION: B ECN: 17900