Model HIF-UPFLOW - Industrial Filters Brochure

HIF 7Not shown: HIF 14, HIF 16, HIF 21, HIF 42, HIF 75, HIF 100 and HIF 150FLHIF 24 HIF 200FLHARMSCO®HIF Up-Flow Cartridge HousingsHARMSCO® Filtration ProductsUtility WaterGround Water RemediationIndustrial Waste Water TreatmentSurface Water Treatment Rule (SWTR) II Process WaterCooling Tower FiltrationResidential and Commercial Drinking WaterReverse Osmosis Pre-filtration304 stainless steel construction, standardElectropolished finish, standard150 psi (10.3 bar) pressure ratingIndividual studs for safe, secure lid closureEasy cartridge installation, removal and serviceExtensive choice of cartridge micron ratings and mediaAll filter housings hydrostatically testedFlow Rates up to 800 gpmOptions:316 stainless steelChemical resistent coatingFlanged options on HIF 24, HIF 42, HIF 75 and HIF 100Features Applications Commercial / IndustrialUp-Flow FiltrationA design so superior it’s patented.RMade in USAThis product is designed with a patented Up-flow technology which prevents the accumulation of air inside the filter housing keeping the filter operating at 100%.HARMSCO EUROPE SRL® Via Salvo D’Acquisto 10a-12 46040 Guidizzolo (MN) ItaliaTel: (0039) 0376 818782 • Fax: (0039) 0376 818399 • E-mail: info@harmscoeurope.com© Harmsco, Inc. 01B 2/11www.harmscoeurope.comHIF 200FLHIF 100 HIF 150FLHIF 75Cartridge Cluster FiltersAll cartridges in our 7, 14, 16, 21 and 24 models are arranged in a single “cartridge cluster,” so all cartridges are removed atone time for easy cartridge cleaning or replacement.HIF 42HIF 24HIF 21HIF 16HIF 14HIF 7Harmsco® HIF Up-Flow Cartridge Housings *Flow rates shown above are for guidelines only. Actual flow rates are based on cartridge type, micron rating, viscosity, solids content and a number of other factors. For complete flow and pressure drop information please refer to your cartridge manufacture guidelines.Filter Model HIF 7 HIF 14 HIF 16 HIF 21 HIF 24 HIF 42 HIF 75 HIF 100 HIF 150FL HIF 200FLFlow Rate* (GPM) Up to 30 Up to 60 Up to 75 Up to 90 Up to 100 Up to 175 Up to 300 Up to 400 Up to 600 Up to 800Flow Rate* (LPM) Up to 113 Up to 226 Up to 284 Up to 340 Up to 397 Up to 662 Up to 1,135 Up to 1,514 Up to 2,271 Up to 3,028Flow Rate* (M3/HR) Up to 7 Up to 14 Up to 17 Up to 20 Up to 23 Up to 40 Up to 68 Up to 91 Up to 136 Up to 181Cartridges 7 - 9-3/4”“Singles”7 - 19-1/2”“Doubles”8 - 19-1/2”“Doubles”7 - 29-1/4”“Triples”8 - 29-1/4”“Triples”14 - 29-1/4”“Triples”25 - 29-1/4”“Triples”50 - 19-1/2”“Doubles”50 - 29-1/4”“Triples”100 - 19-1/2”“Doubles”Ordering InformationFilter Vessel / Metal Components - 304 stainless steel, electropolished for increased resistance to corrosionBottom Seals - natural gum rubber, standard; EPDM, Viton available Wing Nuts - brass; brass hex nuts, stainless steel flat washers availableHolding/ Lifting Rods, Standpipes and Pipe Caps - CPVC, standard models; 304 stainless steel for All-Stainless models Rim Gaskets - EPDM, standard; Buna-N, Viton available Temperature - rated to 140°F (60°C) with CPVC rods, pipe caps, standpipes and standard Harmsco cartridges; to 200°F (93°C) for all stainless models with stainless steelrods, pipe caps and standpipes, and Harmsco High-Temp cartridges; temperature limits vary and depend on pressure and time under loadPressure - rated for pressures to 150 PSI (10.3 bar) maxFlow - up to 800 gpm; typical flow rates are 4-6 gpm per single length (9-3/4”) Harmsco cartridge; published data is for guidelines only; please consult pressure drop chartsO-rings - Buna-N, standard; EPDM, Viton availableSpecificationsDimensionsMade in USADC CDAB BAFilter ModelAHeightBDiameterCLeg WidthDHeight Service Ht. Inlet/Outlet DrainHIF 7 19-1/2” 13” 13” 3-1/2” 35” 1-1/2” NPT 1” NPTHIF 14 28” 13” 13” 3-1/2” 48” 1-1/2” NPT 1” NPTHIF 16 28” 13” 13” 4” 48” 2” NPT 1” NPTHIF 21 37” 13” 13” 3-1/2” 68” 1-1/2” NPT 1” NPTHIF 24 37” 13” 13” 4” 68” 2” NPT 1” NPTHIF 42 40” 18” 18” 5-3/8” 68” 2” NPT 1” NPTHIF 75 42” 20” 20” 6-3/8” 70” 3” NPT 1-1/2” NPTHIF 100 52” 20” 20” 5-7/8” 87” 3” NPT 1-1/2” NPTHIF 150FL 48” 28” 28” 5-3/16” 76” 4” flange 1-1/2” NPTHIF 200FL 58” 28” 28” 5-3/16” 93” 4” flange 1-1/2” NPTFlanged options on HIF 24, HIF 42, HIF 75 and HIF 100HIF 150FLHIF 200FLNote: This publication is to be used as a guide. The data within has been obtained from many sources and is considered to be accurate. Harmsco does not assume liability for the accuracy and/orcompleteness of this data. Changes to the data can be made without notification. Temperature, Pressure, Flow Rates, Differential Pressures, Chemical Combinations and other unknown factors can affect performance in unknown ways. Limited Warranty: Harmsco warrants their products to be free of material and workmanship defects. Determination of suitability of Harmsco products for uses and applications contemplated by Buyer shall be the sole responsibility of Buyer. The end user/installer/buyer shall be liable for the product’s performance and suitability regarding their specific intended applications. End users should perform their own tests to determine suitability for each application.