Model JES 301 - Heated Gas Sample Probe Brochure

GENERAL The JES 301 series of heated gas sampling probe is designed for continuous use with extractive sampling systems even where the sample contains dust and aerosols. Water vapour and high dew-point corrosive gases must be kept above the dew-point to prevent corrosion and sample degradation prior to hot analysis or sample conditioning. The JES 301 is available in several versions which may be custom configured to meet user's specific requirements. The JES 301 incorporates a non-corrosive heated, replaceable ceramic filter element with a filter porosity of 2 micron. The filter element is mounted in an electrically heated and thermally isolated stainless steel housing, which is installed in a weather protection housing. The temperature regula-tion is done by a maintenance free, fully electronic temperature controller with under temperature alarm. The heated line series JH can be easily connected to the JES 301 by a movable PG42 fastening screw. TECHNOLOGY The complete unit, consisting of the heated filter head, temperature controller, mounting flange and probe assembly, can be mounted anywhere horizon-tally or vertically. The probe can be connected with a standard DN65 PN6, Form B flange directly. The flange material is stainless steel. When mounted horizontally, the JES 301 should be inclined at an angle of 5° to 15° to allow any condensate formed to drain away from the filter head. A broad range of different materials for In-Situ probe tubes, electrically heated In-Situ probe tubes and large In-Situ - pre filters make the JES 301 versatile in application. FEATURES A temperature alarm contact signalizes fault and un-der temperature, an over temperature protection avoids overheating. The filters can be replaced easi-ly without any tools and without disconnecting the heated line. conditioning systems CONDITIONING SYSTEMS Gas Sampling Probe JES 301 Page 1 ???? Sampling Conditioning Systems ???? Process Analytics ???? System Integration ???? Gas Generators ???? FTIR-Analysers FEATURES ? Rugged Construction ? Easy filter replacement ? Low maintenance? ? Painted steel enclosure ? Calibration gas inlet ? Microprocessor based temperature controller ? Low temperature contact ? Modular ? Status and alarm display at front side TECHNICAL DATA Filter element SiC; pore size 2 µm; 40/20 x 135 mm Operating pressure 50 ... 150 kPa abs. Mounting flange Option DN 65, PN6; DIN 2573; SS316 2“ ANSI-flange, 150lb. Mounting angle recommended 5°-15° incline to allow condensate drainage Sample gas inlet G3/4“ female thread Sample gas outlet 1/8“ NPT female thread Test gas connection 1/8“ NPT female thread Gas wetted parts 1.4571, SiC, Viton Temperature adjustment Option 5 ... 200°C 5 ... 315°C Factory setting 180°C Ambient temperature -20°C ... +60°C Heater element Approx. 500 Watt Temperature sensor PT100 Power supply Option 230VAC / 50Hz or 115VAC / 60Hz Junction box 160 x 120 x 90 mm (WxHxD) Electrical connection Clamps max. 2,5 mm2 Alarm contakt 250VAC, 2 A Protection class IP65 for electronic Weight Approx. 11 kg Dimensions 160 x 350 x 290 mm (WxHxD) Power consumption Approx. 505 Watt SPECIFICATIONS SPECIFICATIONS Page 2 ORDER CODE Gas sampling probes, 230V 35.00005 JES 301W Unheated sampling probe, DN65/PN6 35.00208 JES 301H Heated sampling probe without tem-perature controller, 230V, DN65/PN6 35.00210 JES 301 Heeated sampling probe with cont-roller and housing (180°C), 230V, DN65/PN6 35.00011 JES 301BP Heated sampling probe with tempera-ture controller, housing and back purge equipment 230V, DN65/PN6 35.00014 JES 301FTIR Heated sampling probe with tempera-ture controller, housing (180°C) and calibration gas (raw gas side), 230V, DN65/PN6 35.00016 JES 301SH Steam heated sampling probe 35.00320 JES 301Z Heated sampling probe with tempera-ture controller and housing (180°C), 230V, 2“ ANSI, 150lb. Sampling pipe Max. 600°C Material Length 35.00060 ER-S10 SS316 (1.4571) 1000 mm 35.00061 ER-S15 SS316 (1.4571) 1500 mm 35.00062 ER-S20 SS316 (1.4571) 2000 mm 35.00063 ER-S25 SS316 (1.4571) 2500 mm 35.00065 ER-S30 SS316 (1.4571) 3000 mm Sampling pipe Max. 1200°C Material Length 35.00050 ER-K10 Kanthal 1000 mm 35.00051 ER-K15 Kanthal 1500 mm 35.00052 ER-K20 Kanthal 2000 mm Sampling pipe Max. 1100°C Material Length 35.00070 ER-H10 SS310 (1.4841) 1000 mm 35.00071 ER-H15 SS310 (1.4841) 1500 mm Heated sampling pipe Max. 200°C Material Length 35.07050 ER-EH05 SS316 500 mm 35.07070 ER-EH07 SS316 700 mm 35.07100 ER-EH10 SS316 1000 mm 35.07150 ER-EH15 SS316 1500 mm 35.07200 ER-EH20 SS316 2000 mm 35.07250 ER-EH25 SS316 2500 mm Page 3 Gas sampling probes, 115V 35.00025 JES 301WZ Unheated sampling probe, 2“ ANSI, 150lb. 35.00209 JES 301HX Heated sampling probe without tempe-rature controller, 115V, DN65/PN6 35.00211 JES 301X Heated sampling probe with temperatu-re controller and housing (180°C), 115V, DN65/PN6 35.00321 JES 301XZ Heated sampling probe with temperatu-re controller and housing (180°C), 115V, 2“ ANSI, 150lb. Sampling pipe Max. 140°C Material Length 35.00080 ER-T10 Teflon 1000 mm 35.00081 ER-T15 Teflon 1500 mm 35.00082 ER-T05 Teflon 500 mm Standard configuration Gas sampling probes Option 1: unheated sampling pipe Option 2: heated sampling pipe Accessories heated sampling pipe 35.07501 HTI-16 Temperature controller, 230V 35.07502 3/4 Thread 3/4“ thread for additional pipe ????? Analysentechnik GmbH Werner Heisenberg-Straße 4 A-2700 Wiener Neustadt Tel. +43 (0) 2622 / 87201 Fax +43 (0) 2622 / 872011 E-Mail: sales@jct.at Web: www.jct.at Specification subject to change without notice. PDS_E_JES301_06/08_Rev. 0 ORDER CODE Consumable parts 35.90010 O-Ring A, 200°C, Viton 35.90011 O-Ring B, 200°C, Viton 35.90012 O-Ring A, 315°C, Kalrez 35.90013 O-Ring B, 315°C, Kalrez Spare parts 35.90014 Filter element SiC F10, 2 µ, 40/20 x 135 35.90015 Gasket for filter element, 200°C, Viton 35.90016 Gasket for filter element, 315°C, Kalrez 35.90100 Spare part kit, consisting of 1 x O-Ring A and B, 1 x filter element SiC F10, 2 x gaskets Viton 35.90018 Surface coated filter element, 40/20x135 35.90050 Heater element; 230V, 50/60 Hz, 500 W 35.90052 Heater element; 115 V, 50/60 Hz, 500 W 35.90060 Thermocouple type K for PCB of JES 300 35.90065 Thermal isolation 35.90080 Male connector SS316, for 6 mm tube 35.90081 Male connector SS316, for 8 mm tube 35.90082 Plug, SS316 35.90083 Male connector, SS316, for 1/4“ tube 35.90084 Male connector, SS316, for 3/8“ tube 35.90085 Elbow connector, SS316, for 6 mm tube 35.90086 Male connector, SS316, for 6 mm tube 35.90087 Adapter for G3/8“ connector SS316, for 10 mm tube 35.90088 Seal SS-6RS-2 35.90230 PCB temperature controller with housing, 230V/115V 35.90260 Temperature sensor PT100 for PCB of JES 301 35.94000 Conversion kit JES 301 consisting of temperature sensor PT100 and PCB 230V/115V Spare parts 0041010039 1.4301 DN65/PN6 to 2 1/2“ 0041010044 1.4301 DN65/PN6 to DN80/PN6 0041010072 1.4301 DN65/PN6 to 3“ 0041010075 1.4571 DN65/PN6 to DN100/PN25 Flange adapter Material Dimensions Page 4 Standard configuration Option 3: In-Situ pre filter In-Situ pre filter, pore size 3 µm, SS 1.4404, Max. 550°C, diameter 50 mm 35.00703 HD-03 Length 300 mm, up to 10 g/m³ 35.00705 HD-05 Length 500 mm, up to 20 g/m³ 35.00710 HD-10 Length 1000 mm, up to 15 g/m³ In-Situ pre filter with V-deflector, pore size 3 µm, SS 1.4404, Max. 550°C, diameter 50 mm 35.00803 HD-03V Length 300 mm, up to 10 g/m³ 35.00805 HD-05V Length 500 mm, up to 20 g/m³ 35.00810 HD-10V Length 1000 mm, up to 15 g/m³ Extension tube For In-Situ pre filter Material Length 35.00910 HD-ET10 SS316 1000 mm 35.00920 HD-ET20 SS316 2000 mm 35.00925 HD-ET25 SS316 2500 mm Extension tube For In-Situ pre filter Material Length 35.00926 HD-ETK25 Kanthal 2500 mm Gasket for extension tube 35.00950 HD-ETGK 3/4“, 27x38,2, SIL C 4400 Consumable parts and flange adaptors Spare parts