Model SAE ISOLOK® Data Sheet 18.1.16

? Collects samples from slide or vertical drop chutes or direct from open processes? Single moving part collects accurate and repeatable 100 cc sample volume? Particle sizes up to 3/4" (19 mm) are accommodated without shearing or degrading sample material? Heavy 316 stainless steel construction features chrome-hardened body bore? Field-replaceable, application-specific seals include EPDM, polyurethane elastomers and more? Extended body with 4" (10 cm) plunger stroke allows for sampling well inside heavy-body/double-wall vessels? Heavy-duty 3" (7.6 cm) clamp ferrule & smooth-bore mounting port for easy installation? ATEX compliantISOLOK® Series SAE Large Capacity Sampler captures a volume of approximately 100 cc per cycle. Particle sizes up to 3/4" (19 mm) are accommodated without shearing or degrading the sampled material. An auxiliary top body port enables air ejection of non-free flowing materials.An air cylinder extends a single plunger into the process material, then immediately withdraws, carrying a fixed amount of sample trapped in an annular ring between plunger seals. Process or flow ports are always closed, preventing leaks or product loss. There are no tubes or passages to become clogged. The gravity-discharged sample is transferred directly to a closed container. Sample integrity is maintained while contamination of personnel or facility is eliminated.ISOLOK® Series SAE Samplers can be used for composite, batch or analysis sampling techniques. Composite sampling is accomplished by obtaining a series of precisely measured material samples at set intervals or adjusted in response to product flow. Samples can be collected in common or individual containers. Batch or analysis sampling in response to immediate need or on-line process control interface is facilitated using single or rapid-cycling material withdrawal.A complete line of programmable automatic controls is available for use in general purpose as well as hazardous environments.www.sentry-equip.com 18.1.16 Rev. 5 02/14ISOLOK ® series sAe sAmplerBulk solids samplerISOLOK® series sAeDescriptionFeaturesLarge Capacity SamplerHandles Large Diameter ParticlesSPECIFICATIONSSample Volume per Cycle 100 ccMaximum Particle Size 0.75" (19 mm)Operating Cycle Range maximum 12 samples/minuteBody Material 316 stainless steel; other alloys availablePlunger Material 316 stainless steel; other alloys availablePlunger Bore x Stroke 2.25" x 4" (57 mm x 102 mm)Plunger Seal Material. polyurethane, EPDM & others availableActuator Material 316 stainless steel; other alloys availableActuator Seal Material filled Teflon®; others availableStatic Seal Material fluoroelastomer; others availableSample Temperature Range -275° to 575°F (-170° to 302°C) depending on seal material & duty cycleAmbient Operating Temperature Range -5° to 131° F (-20° to 55° C) depending on seal materialLine Mount Adapter Type 3" (7.6 cm) clamp ferruleCompressed Air Requirement 0.70 cfm @ 30 psi / 19.82 l/min @ 2.07 bar maximum cycle rangeOverall Dimensions, length x diameter, less accessories 18.2" x 6.5" (462 mm x 165 mm)Net Weight, not including controller or accessories 29 lbs. (13.2 kg)ISOLOK® SAE TECHNICAL DATASAmPLINg PrOCESSplunger extended;process isolatedplunger retracted;sample isolatedand lockedISOLOK® series sae sampler (extended nose sHoWn)© Sentry Equipment Corp 2006 18.1.16 Rev. 5 02/14For further information, contact:It is solely the responsibility of the end-user, through its own analysis and testing, to select products and materials suitable for their specific application requirements, ensure they are properly installed, safely applied, properly maintained, and limit their use to their intended purpose. Improper selection, installation, or use may result in personal injury or property damage.SENTRY® EQUIPMENT CORP 966 Blue Ribbon Circle NorthOconomowoc, WI 53066 USATel: 262-567-7256 • Fax: 262-567-4523E-mail:sales@sentry-equip.comWebsite:www.sentry-equip.comEuropean Authorized Rep:OBELISBd. General Wahis 53-1030Brussels Belgium II 2GD TXTeflon is a registered trademark of E. I. Du Pont de Nemours and Company.