Model Z1 Series - Pressure and Level Transmitter Datasheet

Pressu re and Leve l T ransmi t t e r sProduct SummaryADDRESSSUITE 1TRIDENT BUSINESS VILLAGEKILVERSTONETHETFORDNORFOLK IP24 2RL E-MAILsales@pctflow.comWEBwww.pctflow.comTELEPHONE+44 (0) 1842 753 456FAX+44 (0) 1842 752 424PROCESS CONNECTIONSZ1 SERIES TRANSMITTERSDIMENSIONS (MM)Parts description:1 Cover2 Push buttons / display(behind cover)3 Cover with venting4 Venting5 PG9 cable gland6 O-ring7 Electronic housing8 Foot with cooling fins9 O-ring (code S = 1´ ´BSP)10 O-ring11 M8 Bolt12 Diaphragm and ring13 Weld-on nipple ø 33mm (WTB = 1´ ´ BSP)The Z1 Series transmitter has been designed for measuring pressure and level on applications that may require a flush diaphragm, such as viscous orsticky medias.The flush mounted diaphragms are very robust andare available in a choice of connections such as 1/2”and 1” BSP or NPT.The transmitters are accurate to 0.1% of adjustedspan and fully temperature compensated.Z1 setup is via the front buttons and display.The Z1 also has the ability to simulate the mA loopoutput without pressure being applied.Accuracy : 0,1% of adjusted spanMeasuring ranges : 0 - 0,1 bar to 0 - 60 barOutput signal : 4 - 20 mA / 2-wireHART® protocol (option)PROFIBUS-PA (option)Adjustment : by 3 pushbuttons or H.H.T.Power supply : 12 - 40 VdcExternal load : 600 Ohm / 24V to 1400 Ohm / 40VProtection grade : IP66Process temperature : -20 °C to +100 °CTemperature effect : ±0,015% / KWetted parts : AISI 316 (standard)Electronic housing : AISI 304Process connections : See below. Also available:PMC, Valmet, Valcom connections.Code: XDescription SpecificationsCode WWeld-on nipple diam. 33 mm.Code WTB or WTNThreaded nipple 1´ ´ BSP or NPTCode S or N1´ ´ BSP or 1´ ´ NPTCode WCode WTB/WTNCode S or NTalk to Us about Flow - Pressure - Temp - LevelPROCESS CONNECTIONSZ2 SERIESDIMENSIONS (MM)Parts description:1 Cover2 Push buttons / display(behind cover)3 Cover with venting4 Venting5 PG9 cable gland6 O-ring7 Electronic housing8 Foot9 Lockring10 Weld-on nipple (W) orFlange (F)11 Packing12 DiaphragmThe Z2 Series are designed for all pressure and level applications in the food, beverage, chemical and pharmaceutical industries. All hygienic processconnections are available, most of them are according to the EHEDG, 3A and FDA approvals.The transmitters have very robust flush diaphragmsare accurate to 0.1% of adjusted span and are fullytemperature compensated. Z2 setup is via the front buttons and display.The Z2 also has the ability to simulate the mA loopoutput without pressure being applied.Accuracy : 0,1% of adjusted spanMeasuring ranges : 0 - 0,04 bar to 0 - 60 barOutput signal : 4 - 20 mA / 2-wire HART® protocol (option)PROFIBUS-PA (option)Adjustment : by 3 pushbuttons or H.H.T.Power supply : 12 - 40 VdcExternal load : 600 Ohm / 24V to 1400 Ohm / 40VProtection grade : IP66Process temperature : -20 °C to +100 °C (135° / 30 min)Temperature effect : ±0,015% / KWetted parts : AISI 316 (standard)Electronic housing : AISI 304Process connections : See below (all standard processconnections available)Description SpecificationsCode MMilkcoupling (DN 25, 40 or 50)Code FFlange (DIN or ANSI)Code WWeld-on nipple diam. 85 mm.Code MCode FCode WTechnical Help 01842 753 456 or technical@pctflow.comPROCESS CONNECTIONSZ3 SERIESParts description:1 Cover2 Push buttons + display(behind cover)3 Cover with venting4 Venting5 PG9 cable gland6 O-ring7 Electronic housing8 Foot with cooling fins9 Ceramic sensor10 Process connectionThe Z3 Series pressure transmitter has a ceramicmeasuring sensor. Z3 Series is suitable for pressureapplications on clean liquids, gases and vapours.The ceramic measuring cell can withstand high overpressures and is sealed by an O Ring (viton as standard, other materials on request)The transmitters are accurate to 0.1% of adjustedspan and fully temperature compensated.Z3 setup is via the front buttons and display.The Z3 also has the ability to simulate the mA loopoutput without pressure being applied.Accuracy : 0,1% of adjusted spanMeasuring ranges : 0 - 0,2 bar to 0 - 320 barOutput signal : 4 - 20 mA / 2-wire HART® protocol (option)PROFIBUS-PA (option)Adjustment : by 3 pushbuttons or H.H.T.Power supply : 12 - 40 VdcExternal load : 600 Ohm / 24V to 1400 Ohm / 40VProtection grade : IP66Process temperature : -20°C to +90°CTemperature effect : ±0,015% / KMeasuring sensor : ceramic (Al2O3 / 96%)Sensor sealing : viton o-ring (standard) other materials on requestOther wetted parts : AISI 316 (standard)Material housing : AISI 304Description SpecificationsCode R1/2´ ´ BSP (DIN 16288)Code S1/2´ ´ BSP M / 1/4´ ´ BSP FCode N1/2´ ´ NPT M / 1/4´ ´ NPT FCode RCode SCode NDIMENSIONS (MM)Providing Total Instrumentation Solutions