Multi Purpose Epoxy Coating-HydraLine 4134

HydraTech Engineered Products LLC • 10448 Chester Rd • Cincinnati, OH 45215 • 513-827-9169 1 HydraTech HydraLine 4134 Issue 2.09 Multi Purpose Epoxy Coating PRODUCT DESCRIPTION • The HydraLine 4134 is a unique, high build epoxy coating for corrosion resistant applications. • The 4134 provides excellent adhesion to a variety of substrates while allowing a sag free application at high film builds. • HydraLine 4134 can be filled with chopped fibers to create a polymeric filler / putty or be filled with Portland cement to form a polymeric mortar / grout. • The HydraLine 4134 can be utilized in combination with a variety of woven fabrics to give a structural repair. Advantages • Rapid development of physical properties with ambient cure. No post cure required. • Good Chemical Resistance • Excellent Adhesion • 100% Solvent-Free, Zero V.O.C. • Low temperature cure down to 40ºF (4ºC). • Full contract support services, if required HydraLine 4134 The HydraTech HydraLine 4134 is a performance driven product that provides a chemical and corrosion resistant repair for primary and secondary containment applications. The 4134 is backed by our engineering staff that services each application with assessment and technical support. PHYSICAL PROPERTIES 4134 Color Steel Blue Working Life – 68ºF (20ºC) 15 minutes Dry Times – 68ºF (20ºC) 4 Hours % Vol Solids (ASTM 2369) 100 Shore D Hardness (ASTM D2240) 80 Mix Ratio Pre-measured 1:1/container Flash Point > 200ºF (93ºC) Storage Life Twelve months when stored in original sealed containers, between 50-77ºF (10-25ºC) Adhesion to Cold Rolled Steel (psi) (ASTM D4541) >2,000 Adhesion to Hot Rolled Steel (psi) (ASTM D4541) >2,000 Adhesion to Cast Iron (psi) (ASTM D4541) >2,000 Adhesion to 304 Stainless (psi) (ASTM D4541) >2,000 Adhesion to 316 Stainless (psi) (ASTM D4541) >2,000 Adhesion to Concrete (ASTM D4541) Concrete Failure APPLICATION RECOMMENDATIONS SUBSTRATE PREPARATION Minimum Application Temperature 40ºF (4.4ºC) Maximum Relative Humidity 85% Substrate Temperature 5ºF (3ºC) above dew point Thinning Do not thin Cleaning Fluid Hunting Universal Equipment Cleaner To aid application at low temperatures, both components should be warmed to 60-68ºF (15.5-20ºC) prior to mixing. Substrate preparation dictates the adhesion performance of any coatings system. A properly prepped surface will ensure maximum life and performance of the system. Concrete: NACE No.6* / SSPC-SP 13* Steel: NACE No.2* / SSPC-SP 10* NACE No.3 / SSPC-SP 6 NACE No.5 / SSPC-SP 12 *indicates recommended method www.hydratechllc.com HydraTech Engineered Products LLC • 10448 Chester Rd • Cincinnati, OH 45215 • 513-827-9169 2 HydraTech HydraLine 4134 Issue 2.09 Acid Resistant Epoxy Coating INSTALLATION PROCEDURE • Prep substrate • Mechanically mix together both 4134 components until uniform in color. • Apply 4134 to prepared substrate via brush or spreader. • Allow 4134 to cure a minimum of 24Hr before return to service. NOTE PERFORMANCE DATA CHEMICAL RESISTANCE ASTM D543 (31 day immersion) Water No effect Sodium Hydroxide 5% No effect Ammonium Hydroxide 5% No effect Sodium Hypochlorite (bleach) No effect Ferric Chloride 1% No effect Sulfuric Acid 20% No effect Nitric Acid 1% No effect Detergent Solution No effect Gasoline No effect Toluene No effect (Testing reflects results after seven day cure) ADHESION ASTM D4541 (psi) Cold Rolled Steel >2,000 Hot Rolled Steel >2,000 Cast Iron >2,000 304 Stainless Steel >2,000 316 Stainless Steel >2,000 Concrete Concrete Failure (Testing reflects results after 24Hr cure) The 4134 System is not intended for applications with exposure to strong acids, organic acids, strong solvents (MEK, Acetone, Alcohol). Consult technical staff regarding applications where exposure to organic acids or strong solvents may exist. To be applied by certified personnel only. See MSDS for additional safety information. System will discolor when exposed to sunlight. COVERAGE INHALATION: Wear suitable respiratory cartridge mask in enclosed spaces. Work in well ventilated areas. EYES: Wear suitable goggles. SKIN: Wear protective clothing and gloves made of impervious material. STORAGE: Store away from direct sunlight and sources of heat. Store at 40º to 90ºF (4º to 32ºC). Avoid Freezing. (Primer coverage based on 32mil film build.) KIT SIZE COVERAGE 4134 Pt 4.5 sqft Qt 9 sqft Hg 23.5 sqft ORDER INFORMATION Part No. for standard kits consist of: Product Code - Component – Container Code Pint Kit Quart Kit Half Gallon Kit 4134A63 4134A71 4134A11 4134B63 4134B71 4134B75 *** NOTE: Custom kit quantities can be packaged for special application. *** www.hydratechllc.com www.hydratechllc.com www.hydratechllc.com