Noble TM Specs

TRAILER MATE SPECIFICATIONS TM50 2-Wheel Drive 3-Wheel Drive TABLE OF CONTENTS TM50 2-WD / 3-WD Specifications / Dimensions ……………………………. 1 General Specifications ..………………………………………………….. 2 Weights / Travel Speed / Tilt Table Degrees / Gradeability ….……….. 3 Gradeability conversion Table …………………………………......…… 4 Percent Grade vs. Degree of Angle ……………………………………… 5 Recommended Spare Parts List ……………………………………….... 6 Capacity Table …………………………………..……………………….. 7 Component Specifications ………………………………………………. 8 - 13 TM50 3WD with Flared Fender Option ……………………………….. 14 - 15 Table of Contents COMPONENT SPECIFICATIONS TM50 2-WD / 3-WD DIMENSIONAL DATA - 1 - 100”92” 48” 89.25” 60” Ground Clearance – 8.75”GENERAL SPECIFICATIONS TM50 2-WD / 3-WD SPECIFICATIONS - 2 - GENERAL SPECIFICATIONS Weight of Unit with the following Masts (31” x 15.5” Tires) Mast 3-WD 2-WD 72” 5310 lbs. 5,160 lbs. 96” 5500 lbs. 5,350 lbs. 120” 5640 lbs. 5,490 lbs. 144” 6000 lbs. 5,850 lbs. Travel Speeds - Both 3WD & 2WD Model Forward Reverse 3-WD 9.0 mph (14.5 km/h) 5.9 mph (9.5 km/h) 2-WD 9.0 mph (14.5 km/h) 5.9 mph (9.5 km/h) Tilt Table Degrees (per ASME B56.6) Platform Test Operation Scope Angle Load Longitudinal Stacking 6% 3.4 degrees Rated Capacity Longitudinal Traveling 22% 12.4 degrees Rated Capacity Lateral Stacking 10% 5.7 degrees Rated Capacity Lateral Traveling 40% 21.8 degrees No Load Lateral Stacking 10% 5.7 degrees No Load Gradeability (120” Mast) Configuration Gradeability Speed Left Hand Right Hand Rear (2 Speed) (%) (mph) Ratio Ratio Ratio Low (3-WD) 51% 2.4 24.85 24.85 24.85 High (2-WD) 31% 3.6 24.85 24.85 0 - 3 - GRADEABILITY Conversion Table Degrees to Percentage 100% Since the conversion of gradeability is often referred to 95% in percentages and then on the other hand often referred 90% to in degrees, this chart is being provided for your 85% convenience to quickly convert percents to degrees. 80% 75% 70% 65% 60% 55% Degrees 50% 100’ --45 45% --40 40% --35 35% --30 30% --25 25% --20 20% --15 15% --10 10% --5 5% --0 --- 100 feet --- - 4 - Percent Grade vs. Angle Percent of Grade Angle 1 0 degree 35’ 2 1 degree 9’ 3 1 degree 44’ 4 2 degrees 18’ 5 2 degrees 52’ 6 3 degrees 27’ 7 4 degrees 1’ 8 4 degrees 35’ 9 5 degrees 9’ 10 5 degrees 43’ 11 6 degrees 17’ 12 6 degrees 51’ 13 7 degrees 25’ 14 7 degrees 59’ 15 8 degrees 32’ 16 9 degrees 6’ 17 9 degrees 39’ 18 10 degrees 13’ 19 10 degrees 46’ 20 11 degrees 19’ 21 11 degrees 52’ 22 12 degrees 25’ 23 12 degrees 58’ 24 13 degrees 30’ 25 14 degrees 3’ 26 14 degrees 35’ 27 15 degrees 7’ 28 15 degrees 39’ 29 16 degrees 11’ 30 16 degrees 42’ 35 19 degrees 18’ 40 21 degrees 49’ 45 24 degrees 14’ 50 26 degrees 34’ 55 28 degrees 49’ - 5 - Recommended Spare Parts List Per truck Quantity Part Number Description Quantity Per Machine 60238 BATTERY – 12V 1EA 1 63741 FILTER – TRANS 1EA 1 60369 FILTER – HYD 1EA 1 62274 FILTER – ENGINE OIL 1EA 2 62685 FILTER – AIR 1EA 1 62260 FILTER – FUEL 1EA 2 62756 BELT – FAN 1EA 62190 BELT – ALT 1EA 2 62746 HOSE - LOWER RADIATOR 1EA 2 62747 HOSE - UPPER RADIATOR 1EA 2 64026 SWITCH – PARKING BRAKE 1EA 5 64027 SWITCH – TRACTION CONTROL 1EA 4 64028 SWITCH – TRACTION CONTROL 1EA 4 62284 DRAIN PLUG 1EA 5 60747 DRAIN PLUG SEAL 1EA 5 60925 THERMOSTAT 1EA 5 62263 THERMOSTAT O-RING 1EA 2 62573 RELAY 1EA 3 62312 RELAY – GLOW PLUG 1EA 1 62278 FUSE - 50A GLOW PLUG 2EA 2 62574 FUSE – 10A 2EA 1 62575 FUSE – 15A 2EA 1412759 FUSE – 5A 2EA 1243548 FUSE – 30A 2EA 62665 BULB – FLOODLIGHT 2EA 62663 BULB – IDENT 2EA 60588 BULB - BRAKE & TURN 2EA 60593 LAMP - SIDE MARKER 2EA 62268 SENSOR – TEMP H2O SHUTDOWN 1EA 62281 PLATE – 9 PIN RELAY 1EA 63851 Flash Tube- Strobe 1EA Contact EPI Parts at 806-767-4243 or Fax 888-429-8681 - 6 - MAST PERFORMANCE & CAPACITY TABLE Mast Maximum Overall Tilt Pantograph Pantograph Pantograph Type Fork Height Lowered Degrees Retracted Extended Extended Height Stabilizers Stabilizers Stabilizers Up (1) Up (1) Down (1) in (mm) in (mm) Fwd Back lb lb lb Two 72 (1829) 91 (2312) 5000 3500 5000 Stage 96 (2438) 103 (2618) 5 9 5000 5000 120 (3048) 115 (2922) 5000 5000 144 (3658) 127 (3226) 4000 4000 1. Capacities (Mast Vertical) 24” (500 mm) Load Center. WARNING: Before you lift or place a load over 3500 lbs. Or higher than 72” with the pantograph extended, you must fully lower the stabilizers. Do not raise the stabilizers until you have fully retracted the pantograph. Otherwise, the Trailer Mate could become unstable. STANDARD THREE-WHEEL DRIVE Mast (MFH) in / (mm) 72 (1829) 96 (2438) 120 (3048) 144 (3658) Overall Height Lowered in / (mm) 91 (2311) 103 (2616) 115 (2921) 127 (3226) Capacity @ 24” LC lbs./ (kg) 5000 (2268) 5000 (2268) 5000 (2268) 4000 (1814) Weight lbs. / (kg) 5310 (2408) 5500 (2494) 5640 (2558) 6000 (2721) Extension / Pantograph in / (mm) 48 (1219) 48 (1219) 48 (1219) 45 (1143) Gradeability @ 2 MPH % 53 52 51 49 Tires in 31 x 15.5 Overhead Guard Height in / (mm) 92 (2337) Tilt (± 1) Forward/Back Degrees 5 / 9 Sideshift Total S/S in / (mm) 6 (152) Ground Clearance in / (mm) 8.75 (222) Frame Opening in / (mm) 60 (1524) Overall Width in / (mm) 100 (2540) Overhang in / (mm) 65 (1651) Overall Length in / (mm) 107.5 (2731) Turning Radius in / (mm) 93 (2360) Power HP Cummins 4 Cylinder 2.3L 50 HP water-cooled diesel engine Travel Speed mph / (km/h) Forward – 9.0 (14.5) / Reverse – 5.9 (9.5) - 7 - COMPONENT SPECIFICATIONS - 8 - COMPONENT SPECIFICATIONS ENGINE Cummins 2.3 Liter Diesel Engine • Naturally aspirated, water-cooled diesel for longer life. • Rated 50 hp @ 3000 RPM; Governed to 2700 RPM maximum while producing 50 hp for longer engine life. • Four-cylinder in-line diesel with a swirl chamber gives more complete combustion. • Direct valve operation via overhead cam driven by a toothed belt – simple to replace, lower maintenance costs. • Maintenance-free valve timing gear with hydraulic tappets for lower operating costs. • Distributor fuel injection pump driven with a toothed belt is simple to replace for lower maintenance costs. • Improved combustion keeps exhaust emissions well below restrictive European Standards and reduces customer complaints. • Tight sound –proofing tolerances cuts noise to a hush and reduces operator fatigue. • Enhanced fuel efficiency delivers more power and torque per pound for lower operating costs. General Features: Four-stroke naturally aspirated. Four cylinders in line. Cast Iron cylinder block. Maintenance free hydraulic tappets. Sheet metal sump. Light alloy cylinder head. Five bearing crankshaft. Valves operated by overhead camshaft and toothed belt drive. Sealed pressurized water cooling system. Pressure fed lubricating system, with pump and filter. Mechanical fuel injection system with distributor type pump. Dry air cleaner with paper element. - 9 - COMPONENT SPECIFICATIONS WHEELS AND TIRES Standard High Flotation Tires / For Agricultural and Industrial Service • Tire Size Designation: 31” x 15.50” – 15” NHS • Tire Type: Regular Lug Traction Tread • Ply Rating: 8 ply • Maximum Load: 3660 lbs rolling (5000 lbs static per Tire) • Inflation Pressure: 45 PSI • Section Width: 15.10” • Overall Diameter: 31.40” • Design Rim Width: 13.00” Wheel Rim / 13 lb Rim Contour • Design Rim Width: 13.00” • Nominal Diameter: 15.00” • Flange offset: +2” (outboard of center) • Pilot Diameter (OD): 7.875 +/- .010” • Stud Size: 5/8” – 18 UNF • Number of Studs: 9 each • Bolt Circle: 0 9.500” • Flange Diameter (OD): 11” CAPACITIES Fuel: 6.7 gallons (Consumption Rate – 1 gallon per hour @ full throttle) Engine Oil: 4.77 quarts with filter Hydraulic Oil: 20 gallons Coolant: 5.3 quarts Gear Oil: 0.66 quarts for each drive hub HYRAULIC SYSTEM PRESSURES Transmission Charge Pump: 315 PSI Transmission Loop: 5000 PSI max. Steering Circuit: 2750 PSI max. Implement Circuit: 3000 PSI max. - 10 - COMPONENT SPECIFICATIONS MAST / CARRIAGE Side Shifting Mast: (Allows lateral adjustment of fork-load) • Gives the operator the capability of more precise fork-load placement. • Reduces product damage and allows for better cube utilization. • Also makes it easier to mount the Trailer Mate. Pantograph-Reach Mechanism: Allows forks to extend out 48” to pick up load. Heel of forks extend beyond front of tires when pantograph is fully extended. Allows loads wider than frame opening to be picked up from ground level safely. • Most of the load can be removed from one side of the trailer (compared to a truck with a sliding mast). No need to go out into traffic. • Allows double stacking two pallets deep. • Better space utilization. • Helps keep the horizontal center of gravity within the stability triangle. Double Scissor Pantograph: Improves visibility through the mast when in all positions. • Leads to improved productivity-operator more confident of fork-load position. • Reduces product damage and subsequent clean up. • Eases mounting to trailer. Self-Lubricating Slider blocks on Mast and Pantograph: Spreads contact load over larger area and reduces maintenance compared to rollered mast. • Reduces wear on mast rails – due to larger contact area. • Blocks can be replaced in a matter of minutes with no mast or carriage disassembly. • Self-lubricating blocks reduce need for greasing. • No high cost roller bearings to fail. Center Seating: Allows operator to be seated directly behind the center of the mast. • Gives the operator a clear and in-line view of both drive wheels and both fork tips for more positive load placement. • Reduces product damage and subsequent clean up costs. • Also gives the operator a more comfortable ride. • Provides space between operator & obstructions on either side of machine. - 11 - COMPONENT SPECIFICATIONS Tight 93” Turning Radius (3-WD): Allows work to be done in tight quarters. • Gives the operator the potential of working in tighter quarters than most competitive machines. • Reduces space required for maneuvering the vehicle-especially around residential construction sites. Hydrostatic Power Steering Standard on both 2-Wheel and 3-Wheel Drive: Reduces steer effort. • Unlike a rear caster wheel or dolly, the TM50 gives the operator precise control of lateral movement. • Allows operator with a lower skill level to operate the TM50 vs. some competitive units. • Turning radius is the same in both directions. Hydrostatic Drive: Provides for Horizontal Movement. No Shifting required. • Eliminates need for service brakes. • No clutch packs or brake lining and drums to wear. • Reduces maintenance cost vs. a truck with conventional transmission, torque converter set up. • Gives the operator infinitely variable control of the speed and torque range. • Improves productivity vs. a mechanical drive. On demand traction control: Applies equal torque to all Drive wheels only as required. • Helps reduce heat build up in system and provides better fuel efficiency than if the traction lock was engaged all the time. • Provides longer component life and lower fuel costs. • Operator has more precise control over steering. - 12 - COMPONENT SPECIFICATIONS Detent in stabilizer valve spool: Ensures that valve lever remains engaged until stabilizer is fully extended or retracted. • Minimizes potential damage to stabilizer. • Reduces likelihood that operator may extend the pantograph without stabilizers being fully engaged or try to travel without stabilizers being fully disengaged. Check valve in stabilizers: Prevents oil from flowing out of the stabilizers when in use if a hydraulic line should fail. • Helps prevent an unstable condition that could occur if a hydraulic line should fail while stabilizers are in use. O-Ring Face Seals at all hydraulic connections: Virtually eliminates leaks. • Substantially reduces leaks and therefore customer complaints. No leaks mean fewer oil spots on floor that people can slip on or need to clean up. • Reduces the possibility for the system to be contaminated, because fewer repairs are required and exposure to dirt is minimized. Excellent service and daily maintenance accessibility: Reduce maintenance costs. • The easier something is to do, the greater the likelihood that it will be done. • All daily maintenance checks can be performed from the right hand side of the vehicle after the hood has been opened. • Reduces maintenance time and cost. • Missing daily maintenance checks can lead to major truck failures, so we made them easy to do. All major engine components can be removed and replaced. - 13 - COMPONENT SPECIFICATIONS Notes: - 14 - TM50 3-Wheel Drive with Load Support Option. COMPONENT SPECIFICATIONS Notes: - 15 - TM50 3-Wheel Drive With Load Support Option. COMPONENT SPECIFICATIONS -Page 16- TM50 3-Wheel Drive with High Air Intake