P-201 Series `HE` Horizontal Pumps Brochure

ENERGY SAVING CENTRIFUGAL PUMPS FOR: ACID / AQUEOUS / CAUSTIC CHEMICAL / ETCHING / PHOTOGRAPHICPLATING / SCRUBBING / WASTESSERIES 'HE' HORIZONTAL PUMPSSERIES 'HE' SHOWN WITH 'DRI-STOP' PROTECTION,TO PREVENT DAMAGE FROM DRY OPERATIONHere is a pump capable of "total" chemical resistance, both internally and externally with its non-metallic construction of all wetted components, choice of seal assembly and elastomer materials. The use of engineered plastics in a choice of materials provide excellent chemical compatibility for the most demanding applications.The totally enclosed impeller is molded to close tolerances which allow this pump to operate at peak horsepower efficiency across a broad range of operational flow/head requirementsBULLETINP-201_TAUG 2010WASTETREATMENTFILTERSYSTEMPRESSURESPRAYINGSOLUTION TRANSFERw/PRIMING CHAMBER• Flows to 175 U.S. GPM or 130 ft. TDH @ 60 Hz(552 LPM or 28 M @ 50 Hz)• Non-metallic solution contactHigh temperature polypropylene, CPVC, PVDF or ECTFE (Refer to a chemical resistance chart)• Single or double mechanical seal,carbon/ceramic, or silicon carbide with EPDM or Viton® elastomers• Centrifugal - quiet, vibration-free• NPT or metric connections available• Pump casing indexes to six directions of discharge• Chemical duty motor (1.0 - 7.5 HP)Sealed oversized bearings, liquid/vapor seal and slinger, cast iron end bells, corrosion resistant two-part epoxy finish, stainless steel nameplate, 1.15 service factor at 50 or 60 Hz.The external mechanical seal and impeller sleeve design isolates metal components to provide non-metallic solution contact with the pumped solution. The standard (M8) seal assembly has silicon carbide seal faces and is the most durable and longest lasting mechanical seal available. The double mechanical seal models require water lubrication of the seal faces and allows the pump to be used for solutions containing abrasives, high salt concentrations and for electroless plating solutions. Either Viton or EPDM elastomers are available on the 'HE' pump.MOTORWT.*MOTOR HP A B C D E F G H J Lbs.NEMA1.5 (& 1 @ 1725 RPM) 16.94 8.63 3.5 5.5 6.75 10.5 4 4.75 9.25 432 (& 1.5 @ 1725 RPM) 18 8.63 3.5 5.5 6.75 10.5 5 5.75 9.25 443 19.63 9.63 4.5 7.5 9 11.25 4.5 5.5 10.25 505 21 9.63 4.5 7.5 9 11.25 5.5 6.5 10.25 657.5 21 9.63 4.5 7.5 9 11.25 5.5 6.5 10.25 110SERIES 'HE' Specifications and Performance Curves*For shipping weight, add 15 lbs (6.8 Kg.) to motor weight.DIMENSIONS for NEMA motors are in inches and those for metric motors are in mm.DIMENSIONS in inches (mm) P-201_TPage 2AFHG2-5/8(67)5-3/4(146)2-3/4(70)7-3/4(246)1-1/2” NPT2”NPT8-9/16(217)BDJCEGPM @ 3450 RPM, 60 HzLPM @ 2850 RPM, 50 Hz1725 RPM @ 60 Hz1450 RPM @ 50 Hz*METRICMOTOR KW A B C D E F G H J Kg.1.5 (90S frame) 496 212 90 140 170 307 100 125 236 232.2 (90L frame) 521 212 90 140 170 307 125 150 236 253.0 (100 frame) 549 236 100 160 197 314 140 172 246 30Standard models are constructed of CPVC, polypropylene, PVDF, or ECTFE with threaded connections. The motor shaft is protected by the impeller sleeve assembly. Elastomers are EPDM or Viton. Impellers are enclosed. The mechanical seal is type 21, externally mounted with stainless steel components not in solution contact. A double mechanical seal is recommended for solutions containing abrasives and for high temperature or other critical service. Close coupled motors are NEMA 'JM' or metric (IEC) standard. The motors designated NEMA can operate on 50 or 60 Hz at full rated horsepower. Consult Application Engineering Department for BSP fittings or adapters.P-201_TPage 3SERIES 'HE' Specifications and Ordering InformationFLOWCURVENO.CPVC/EPDM PRICECODENUMBERPOLYPROPYLENE**/EPDM PRICECODENUMBERMODEL NO. MODEL NO.1 H2 x 11/2 CE1L(M8) -D1.5 42-0110A H2 x 11/2 PE1L(M8) -D1.5 42-0410A2 H2 x 11/2 CE2L(M8) -D2.0 42-0120B H2 x 11/2 PE2L(M8) -D2.0 42-0420B3 H2 x 11/2 CE3L(M8) -D3.0 42-0130C H2 x 11/2 PE3L(M8) -D3.0 42-0430C4 H2 x 11/2 CE4L(M8) -D5.0 42-0140D H2 x 11/2 PE4L(M8) -D5.0 42-0440D5 H2 x 11/2 CE5L(M8) -D7.5 42-0150E H2 x 11/2 PE5L(M8) -D7.5 42-0450E6 H2 x 11/2 CE6L(M8) -H1.0 42-0160F H2 x 11/2 PE6L(M8) -H1.0 42-0460FFLOWCURVENO.PVDF/Viton PRICECODENUMBERECTFE/EPDM PRICECODENUMBERMODEL NO. MODEL NO.1 H2 x 11/2 KE1V(M8) -D1.5 42-0318A H2 x 11/2 HE1L(M8) -D1.5 42-0610A2 H2 x 11/2 KE2V(M8) -D2.0 42-0328B H2 x 11/2 HE2L(M8) -D2.0 42-0620B3 H2 x 11/2 KE3V(M8) -D3.0 42-0338C H2 x 11/2 HE3L(M8) -D3.0 42-0630C4 H2 x 11/2 KE4V(M8) -D5.0 42-0348D H2 x 11/2 HE4L(M8) -D5.0 42-0640D5 H2 x 11/2 KE5V(M8) -D7.5 42-0358E H2 x 11/2 HE5L(M8) -D7.5 42-0650E6 H2 x 11/2 KE6V(M8) -H1.0 42-0368F H2 x 11/2 HE6L(M8) -H1.0 42-0660FORDERING INFORMATIONSelect flow curve number providing the desired performance. Then match to Model Number listed below. Standard models include silicon carbide single mechanical seal with EPDM or Viton elastomers. Motor HP is non-overloading at full capacity with 1.1 specific gravity fluids.For standard CPVC, PP, PVDF, and ECTFE pump-motor combination, select model from TABLE 1. For other pump-motor combinations, select from TABLE II.TABLE I STANDARD MODELS** Polypropylene models are glass reinforcedPUMP/MOTOR MODEL NUMBERTO ORDER FROM TABLE II To determine pump-motor for a selected GPM, TDH and/or specific gravity, select flow/pressure point on curve. Required HP is determined by moving vertically to corresponding dotted line and then horizontally to HP scale. Multiply indicated HP by specific gravity. Select pump materials and mechanical seal(s) and construct Model and Price Code No.PRICE CODE NO.H2x1-1/2KE 1 V(M8xM1) -D1.5 = 42-0319AMOTORLong-coupled kit includes cast iron bearing pedestal frame, fiberglass reinforced channel (23-1/2" x 10" x 2-3/4"), flexible coupling and guard, and stainless steel shaft and fasteners. (Order pump separately)OPTIONALSEALIMPELLER2900 MacArthur Blvd. Northbrook, IL. 60062-2005 U.S.A. email: sales@serfilco.com (800) 323-5431 (847) 509-2900 Fax: (847) 559-1141 www.serfilco.com F.O.B. Northbrook, Illinois Specifications subject to change without notice.P-201_TPage 4 * Ceramic is silica free** SERIES 'HE' Ordering Information and Optional EquipmentRegistered Trademark: Viton - DuPont Dow ElastomersPUMPPRICECODENO.CPVCH2 x 1-1/2CE 42-01PVDFH2 x 1-1/2KE 42-03POLYPROP.H2 x 1-1/2PE 42-04ECTFEH2X1-1/2HE 42-06FLOWCURVENO.ADD TO . . .MODELNO. PRICE123456123456123456'O'-RING & MECHANICALSEAL MATERIAL(SOLUTION CONTACT)ADD TO . . .MODELNUMBERPRICE CODENO. SINGLE MECHANICAL SEALEPDM CARBON/CERAMIC* L(M1) 1EPDM SILICON CARBIDE L(M8) 0VITON CARBON/CERAMIC* V(M2) 2VITON SILICON CARBIDE V(M8) 8DOUBLE MECHANICAL SEAL**EPDM CARBON/CERAMIC* L(M1xM1) 5EPDM SILICON CARBIDE L(M8xM1) 4VITON CARBON/CERAMIC* V(M2xM1) 6VITON SILICON CARBIDE V(M8xM1) 9TEFC 208-230/460/3/60 or190/380-415/3/50RPMNEMA MOTORSADD TO . . .HPMODELNUMBERPRICECODE NUMBER3450or2850D1.5D2.0D3.0D5.0D7.5ABCDE1725or1450H1.0H1.5FGDESCRIPTION PRICE CODENUMBERFLANGE CONNECTIONSANSI 150 Lbs. (ASA 150) 2"x1-1/2"(not installed)CPVC 42-0200PVDF 42-0211Polypropylene 42-0218STAINLESS STEEL SHAFT 42-0230METRIC PIPE ADAPTER SETS Consult Application Sales Dept.LONG COUPLED KITMODEL FOR MOTOR FRAME PRICE CODE NUMBERLCK-1 182T & 184T 42-0201ALCK-2 143T & 145T 42-0202ALCK-3 56 42-0203ALCK-4 182 & 184 42-0205AMOTOR MOUNTING & ALIGNMENT 42-0204TABLE IIEXAMPLEPUMPA DRI-STOP pressure switch is available to prevent damage to pump due to dry operation; consult Bulletin A-105.