Trelleborg Sealing Solutions
Pneumatic Seals Catalog
3QHXPDWLF?6HDOV 999.9 mm and up to 2.600 mm usethe RG45 series Turcon® Glyd Ring® .ARG3Material Code (Seal Ring)TSS Series No.TSS Article No. -Type (Standard)*0800 Z80Material Code (O-Ring)N0Rod diameter x 10Quality Index (Standard)* Ordering Turcon® Glyd Ring® with radial notchesplease use suffix “N” in the fifth character.Rod seal - Type ARG13Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type ARGFigure 3 Installation drawingTable XIV Standard installation dimensionsTSS SeriesNo.Rod diameterdN f8/h9GroovediameterGroovewidthRadius RadialclearanceSmaxO-RingdiameterStandardrangeAvailablerangeD1 H8 L1 +0.15 r1 0 - 5 MPa d2ARG0 3 - 14.9 3 - 49.9 dN +4.0 2.00 0.5 0.25 1.78ARG1 15 - 29.9 6 - 119.9 dN +6.0 2.85 0.5 0.50 2.62ARG2 30 - 59.9 7 - 399.9 dN +7.5 3.80 0.8 0.50 3.53ARG3 60 - 199.9 16 - 799.9 dN +12.5 5.60 1.3 0.70 5.33ARG4 200 - 399.9 110 - 799.9 dN +15.0 7.55 1.5 0.90 7.00ARG8 400 - 999.9 150 - 999.9 dN +18.0 7.55 1.5 0.90 7.00Alternative installation with rod dimensionshaving tolerance f8/h9 and groove diametertolerance H9To obtain consistent compression of the O-Ring therecommended groove diameter tolerance is H8, but for awide diamter range H9 is also applicable as per Table XV.Table XV Alternative installation dimensionsgroove tolerance H9TSS Series No. Rod diameterdN f8/h9Groove diameterAvailable range D1 H9ARG0 3 - 29.9 dN +4.0ARG1 6 - 79.9 dN +6.0ARG2 7 - 249.9 dN +7.5ARG3 16 - 449.9 dN +12.5ARG4 110 - 399.9 dN +15.0ARG8 150 - 399.9 dN +18.0L1r max. 0.3r1PressurePressureSd ND1d 2Rod seal - Type ARG14Latest information available at www.tss.trelleborg.comEdition January 2009Table XVI Installation dimensions / TSS Part No.RoddN f8/h9GrooveDiameterD1 H8GrooveWidthL1 +0.15TSSPart No.O-ringSizes3.0* 7.0 2.00 ARG000030 3.68 x 1.784.0* 8.0 2.00 ARG000040 4.47 x 1.785.0* 9.0 2.00 ARG000050 5.60 x 1.805.5* 9.5 2.00 ARG000055 6.07 x 1.786.0 10.0 2.00 ARG000060 6.70 x 1.807.0* 11.0 2.00 ARG000070 7.65 x 1.788.0* 12.0 2.00 ARG000080 8.75 x 1.809.0 13.0 2.00 ARG000090 9.50 x 1.8010.0* 14.0 2.00 ARG000100 10.60 x 1.8010.0* 16.0 2.85 ARG100100 10.77 x 2.6211.0 15.0 2.00 ARG000110 11.80 x 1.8012.0 16.0 2.00 ARG000120 12.42 x 1.7812.0* 18.0 2.85 ARG100120 12.37 x 2.6214.0* 20.0 2.85 ARG100140 14.50 x 2.6515.0* 21.0 2.85 ARG100150 15.54 x 2.6216.0* 22.0 2.85 ARG100160 17.12 x 2.6218.0* 24.0 2.85 ARG100180 18.72 x 2.6218.0* 25.5 3.80 ARG200180 18.66 x 3.5319.0 25.0 2.85 ARG100190 20.29 x 2.6220.0 26.0 2.85 ARG100200 20.29 x 2.6220.0* 27.5 3.80 ARG200200 20.22 x 3.5322.0 28.0 2.85 ARG100220 23.47 x 2.6222.0* 29.5 3.80 ARG200220 21.82 x 3.5323.0* 30.5 3.80 ARG200230 23.40 x 3.5324.0 30.0 2.85 ARG100240 25.07 x 2.6225.0 31.0 2.85 ARG100250 25.07 x 2.6225.0* 32.5 3.80 ARG200250 25.00 x 3.5325.4 31.4 2.85 ARG100254 26.64 x 2.6226.0* 33.5 3.80 ARG200260 26.58 x 3.5328.0 34.0 2.85 ARG100280 28.24 x 2.6228.0* 35.5 3.80 ARG200280 28.17 x 3.5330.0* 37.5 3.80 ARG200300 31.35 x 3.5332.0* 39.5 3.80 ARG200320 32.92 x 3.5333.0* 40.5 3.80 ARG200330 34.52 x 3.5335.0* 42.5 3.80 ARG200350 36.09 x 3.5336.0* 43.5 3.80 ARG200360 37.69 x 3.5338.0* 45.5 3.80 ARG200380 37.69 x 3.5338.0* 50.5 5.60 ARG300380 40.64 x 5.3340.0 47.5 3.80 ARG200400 40.87 x 3.5340.0* 52.5 5.60 ARG300400 40.64 x 5.3342.0 49.5 3.80 ARG200420 44.04 x 3.5344.0* 56.5 5.60 ARG300440 46.99 x 5.33RoddN f8/h9GrooveDiameterD1 H8GrooveWidthL1 +0.15TSSPart No.O-ringSizes45.0* 52.5 3.80 ARG200450 44.04 x 3.5345.0* 57.5 5.60 ARG300450 46.99 x 5.3348.0 55.5 3.80 ARG200480 47.22 x 3.5350.0 57.5 3.80 ARG200500 50.39 x 3.5350.0* 62.5 5.60 ARG300500 53.34 x 5.3350.8 58.3 3.80 ARG200508 51.50 x 3.5552.0 59.5 3.80 ARG200520 53.57 x 3.5353.0* 65.5 5.60 ARG200530 56.52 x 5.3355.0 62.5 3.80 ARG200550 56.74 x 3.5356.0 63.5 3.80 ARG200560 56.74 x 3.5356.0* 68.5 5.60 ARG300560 56.52 x 5.3357.0 64.5 3.80 ARG200570 56.74 x 3.5358.0 65.5 3.80 ARG200580 59.92 x 3.5360.0* 72.5 5.60 ARG300600 62.87 x 5.3363.0* 75.5 5.60 ARG300630 66.04 x 5.3365.0* 77.5 5.60 ARG300650 66.04 x 5.3367.0 79.5 5.60 ARG300670 69.22 x 5.3368.0* 80.5 5.60 ARG300680 69.22 x 5.3370.0* 82.5 5.60 ARG300700 72.39 x 5.3373.0 85.5 5.60 ARG300730 75.57 x 5.3375.0* 87.5 5.60 ARG300750 78.74 x 5.3376.2 88.7 5.60 ARG300762 78.74 x 5.3377.0 89.5 5.60 ARG300770 78.74 x 5.3379.0* 91.5 5.60 ARG300790 81.92 x 5.3380.0* 92.5 5.60 ARG300800 81.92 x 5.3382.5 95.0 5.60 ARG300825 85.09 x 5.3385.0* 97.5 5.60 ARG300850 88.27 x 5.3388.0* 100.5 5.60 ARG300880 91.44 x 5.3390.0* 102.5 5.60 ARG300900 91.44 x 5.3395.0* 107.5 5.60 ARG300950 97.79 x 5.3398.0* 110.5 5.60 ARG300980 100.97 x 5.33100.0* 112.5 5.60 ARG301000 104.14 x 5.33101.6 114.1 5.60 ARG301016 104.14 x 5.33105.0* 117.5 5.60 ARG301050 107.32 x 5.33107.0* 119.5 5.60 ARG301070 110.49 x 5.33108.0 120.5 5.60 ARG301080 110.49 x 5.33110.0* 122.5 5.60 ARG301100 113.67 x 5.33115.0 127.5 5.60 ARG301150 116.84 x 5.33115.0* 130.0 7.55 ARG401150 116.84 x 7.00117.0* 132.0 7.55 ARG401170 120.02 x 7.00120.0* 132.5 5.60 ARG301200 123.19 x 5.33120.0 135.0 7.55 ARG401200 123.19 x 7.00Rod seal - Type ARG15Latest information available at www.tss.trelleborg.comEdition January 2009RoddN f8/h9GrooveDiameterD1 H8GrooveWidthL1 +0.15TSSPart No.O-ringSizes123.00* 138.0 7.55 ARG401230 123.19 x 7.00125.0 137.5 5.60 ARG301250 126.37 x 5.33125.0* 140.0 7.55 ARG401250 126.37 x 7.00127.0 139.5 5.60 ARG301270 129.54 x 5.33130.0 142.5 5.60 ARG301300 132.72 x 5.33130.0* 145.0 7.55 ARG401300 132.72 x 7.00132.0 144.5 5.60 ARG301320 135.89 x 5.33133.0* 148.0 7.55 ARG401330 135.89 x 7.00135.0 147.5 5.60 ARG301350 135.89 x 5.33135.0* 150.0 7.55 ARG401350 135.89 x 7.00140.0 152.5 5.60 ARG301400 142.24 x 5.33140.0* 155.0 7.55 ARG401400 142.24 x 7.00142.0* 157.0 7.55 ARG401420 142.24 x 7-00145.0 157.5 5.60 ARG301450 148.49 x 5.33145.0* 160.0 7.55 ARG401450 145.42 x 7.00150.0 162.5 5.60 ARG301500 151.77 x 5.33150.0* 165.0 7.55 ARG401500 151.77 x 7.00152.4 164.9 5.60 ARG301524 151.77 x 5.33155.0 167.5 5.60 ARG301550 158.12 x 5.33155.0* 173.0 7.55 ARG801550 158.12 x 7.00160.0 172.5 5.60 ARG301600 164.47 x 5.33160.0* 178.0 7.55 ARG801600 164.47 x 7.00165.0 177.5 5.60 ARG301650 170.82 x 5.33165.0* 183.0 7.55 ARG801650 170.82 x 7.00170.0 182.5 5.60 ARG301700 170.82 x 5.33170.0* 188.0 7.55 ARG801700 177.17 x 7.00175.0 187.5 5.60 ARG301750 177.17 x 5.33175.0* 193.0 7.55 ARG801750 177.17 x 7.00180.0 192.5 5.60 ARG301800 183.52 x 5.33180.0* 198.0 7.55 ARG801800 183.52 x 7.00190.0 202.5 5.60 ARG301900 196.22 x 5.33190.0* 208.0 7.55 ARG801900 196.22 x 7.00194.0 206.5 5.60 ARG301940 202.57 x 5.33195.0* 213.0 7.55 ARG801950 202.57 x 7.00200.0* 215.0 7.55 ARG402000 202.57 x 7.00203.2 218.2 7.55 ARG402032 202.57 x 7.00205.0 220.0 7.55 ARG402050 208.90 x 7.00210.0 225.0 7.55 ARG402100 215.27 x 7.00215.0 230.0 7.55 ARG402150 215.27 x 7.00220.0* 235.0 7.55 ARG402200 215.27 x 7.00230.0* 245.0 7.55 ARG402300 227.97 x 7.00240.0 255.0 7.55 ARG402400 240.67 x 7.00RoddN f8/h9GrooveDiameterD1 H8GrooveWidthL1 +0.15TSSPart No.O-ringSizes250.0 265.0 7.55 ARG402500 253.37 x 7.00254.0 269.0 7.55 ARG402540 253.37 x 7.00260.0 275.0 7.55 ARG402600 266.07 x 7.00265.0 280.0 7.55 ARG402650 266.07 x 7.00268.0 283.0 7.55 ARG402680 266.07 x 7.00270.0 285.0 7.55 ARG402700 266.07 x 7.00280.0 295.0 7.55 ARG402800 278.77 x 7.00290.0 305.0 7.55 ARG402900 291.47 x 7.00300.0 315.0 7.55 ARG403000 304.17 x 7.00304.8 319.8 7.55 ARG403048 304.17 x 7.00310.0 325.0 7.55 ARG403100 316.87 x 7.00320.0 335.0 7.55 ARG403200 316.87 x 7.00330.0 345.0 7.55 ARG403300 329.57 x 7.00340.0 355.0 7.55 ARG403400 342.27 x 7.00350.0 365.0 7.55 ARG403500 354.97 x 7.00360.0 375.0 7.55 ARG403600 367.67 x 7.00370.0 385.0 7.55 ARG403700 367.67 x 7.00380.0 395.0 7.55 ARG403800 380.37 x 7.00400.0 418.0 7.55 ARG804000 405.26 x 7.00425.0 443.0 7.55 ARG804250 430.66 x 7.00450.0 468.0 7.55 ARG804500 456.06 x 7.00475.0 493.0 7.55 ARG804750 481.38 x 7.00500.0 518.0 7.55 ARG805000 506.86 x 7.00525.0 543.0 7.55 ARG805250 532.26 x 7.00550.0 568.0 7.55 ARG805500 557.66 x 7.00575.0 593.0 7.55 ARG805750 582.68 x 7.00600.0 618.0 7.55 ARG806000 608.08 x 7.00650.0 688.0 7.55 ARG806500 658.88 x 7.00700.0 718.0 7.55 ARG807000 704.49 x 7.00750.0 768.0 7.55 ARG807500 754.49 x 7.00800.0 818.0 7.55 ARG808000 804.49 x 7.00850.0 868.0 7.55 ARG808500 854.49 x 7.00900.0 918.0 7.55 ARG809000 904.49 x 7.00950.0 968.0 7.55 ARG809500 954.49 x 7.00999.9 1017.9 7.55 ARG809999 1004.39 x 7.0* Standard diameter for Turcon® Glyd Ring® RG58Other dimensions and all intermediate sizes up to999.9 mm diameter can be supplied.For rod diameters >999.9 mm and up to 2.600 mm usethe RG45 series Turcon® Glyd Ring®.Piston Seal - Type APDE16Latest information available at www.tss.trelleborg.comEdition January 2009Piston seal type APDEDescriptionSingle acting piston seal with U-shaped cross-section. Fordouble acting pistons, two seals are used ”back to back”.Special lip design for pneumatic application to maintainlubricating film and minimize friction.Suitable for cylinders with pneumatic cushioning.Technical dataOperatingpressure: 1.6 MPaSpeed: d 1 m/sTemperature: from -40 °C to +80 °CMedia: oil free air (initial grease lubricationrequired), lubricated air, nonagressivegasesMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationSnap-in installation into closed grooves.It is important to remove all sharp edges and burrs fromthe groove and tube before installation.Ordering examplePiston Seal,type APDEPiston diameter: D = 50 mmGroove width: L = 7.5 mmTSS Part No.: APDE00500 (Table XVII)Material No.: WU9E1Material CodeTSS Series No.TSS Article No. 0500 WU9E1-Piston diameter x 10APDE0Piston Seal - Type APDE17Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type APDEBL b1d D1D20°-30°R 0.2Figure 4 Installation drawingTable XVII Installation dimensions / TSS Part No.BorediameterFlangediameterGroovediameterGroovewidthRingwidthInletchamferTSS Part No.D H10 D1 h10 d h10 L +0.2 B b14.0 3.0 1.5 2.0 1.5 1.0 APDE000405.0 4.0 2.5 2.0 1.5 1.0 APDE000506.0 5.0 3.0 2.5 2.0 1.0 APDE000608.0 7.0 4.0 3.0 2.55 1.5 APDE000808.0 7.0 4.8 2.7 2.3 1.5 APDE100808.0 7.0 4.8 3.0 2.55 1.5 APDE2008010.0 9.0 6.0 3.0 2.55 1.5 APDE0010012.0 11.0 7.0 3.0 2.55 1.5 APDE0012013.0 12.0 8.0 3.0 2.55 1.5 APDE0013014.0 13.0 8.0 3.0 2.55 1.5 APDE0014015.0 14.0 9.0 3.0 2.55 1.5 APDE0015016.0 15.0 10.0 3.0 2.55 2.0 APDE0016017.0 16.0 11.0 3.0 2.55 2.0 APDE0017018.0 17.0 12.0 3.0 2.55 2.0 APDE0018020.0 19.0 12.0 6.0 5.5 2.0 APDE2020020.0 19.0 14.0 3.0 2.55 2.0 APDE0020020.0 19.0 14.0 4.5 4.0 2.0 APDE1020022.0 21.0 16.0 3.0 2.55 2.0 APDE0022024.0 23.0 18.0 3.0 2.55 2.0 APDE0024025.0 24.0 17.0 6.0 5.5 2.0 APDE1025025.0 24.0 19.0 3.5 3.25 2.0 APDE0025025.0 24.0 19.0 4.5 4.0 2.0 APDE2025028.0 27.0 18.0 7.5 7.0 2.0 APDE1028028.0 27.0 22.0 3.5 3.25 2.0 APDE00280Piston Seal - Type APDE18Latest information available at www.tss.trelleborg.comEdition January 2009BorediameterFlangediameterGroovediameterGroovewidthRingwidthInletchamferTSS Part No.D H10 D1 h10 d h10 L +0.2 B b130.0 29.0 22.0 3.5 3.25 2.0 APDE0030032.0 31.0 24.0 3.5 3.25 2.0 APDE0032032.0 31.0 24.0 6.0 5.5 2.0 APDE1032035.0 34.0 27.0 3.5 3.25 2.0 APDE0035036.0 35.0 28.0 3.5 3.25 2.0 APDE0036038.0 37.0 30.0 3.5 3.25 2.0 APDE0038038.0 37.0 30.0 6.0 5.5 2.0 APDE1038040.0 39.0 30.0 7.5 7.0 2.5 APDE0040040.0 39.0 32.0 3.5 3.25 2.5 APDE1040042.0 41.0 30.0 6.5 6.0 2.5 APDE1042042.0 41.0 34.0 3.5 3.25 2.5 APDE0042045.0 44.0 37.0 3.5 3.25 2.5 APDE0045050.0 49.0 40.0 5.5 5.0 2.5 APDE2050050.0 49.0 40.0 7.5 7.0 2.5 APDE0050050.0 49.0 42.0 3.5 3.25 2.5 APDE1050052.0 51.0 42.0 4.5 4.25 2.5 APDE0052055.0 54.0 45.0 7.5 7.0 2.5 APDE0055058.0 57.0 48.0 4.5 4.25 2.5 APDE0058060.0 59.0 50.0 5.7 5.0 2.5 APDE0060060.0 59.0 50.0 7.5 7.0 2.5 APDE1060063.0 62.0 53.0 4.5 4.25 2.5 APDE1063063.0 62.0 53.0 7.5 7.0 2.5 APDE0063065.0 64.0 55.0 7.5 7.0 2.5 APDE0065068.0 67.0 58.0 5.5 4.7 2.5 APDE0068070.0 69.0 58.0 9.5 8.5 2.5 APDE0070075.0 74.0 63.0 9.5 8.5 2.5 APDE0075080.0 79.0 67.3 7.0 6.35 2.5 ADPE2080080.0 79.0 68.0 9.5 8.5 2.5 APDE0080080.0 79.0 70.0 4.5 4.25 2.5 APDE1080085.0 84.0 73.0 9.5 8.5 2.5 APDE0085090.0 89.0 78.0 9.5 8.5 2.5 APDE0090090.0 89.0 80.0 4.5 4.25 2.5 APDE10900100.0 99.0 88.0 9.5 8.5 2.5 APDE01000100.0 99.0 90.0 4.5 4.25 2.5 APDE21000110.0 109.0 95.0 11.0 10.0 3.0 APDE01100120.0 119.0 105.0 11.0 10.0 3.0 APDE01200125.0 124.0 105.0 8.5 8.25 3.0 APDE01250125.0 124.0 110.0 11.0 10.0 3.0 APDE11250140.0 139.0 120.0 8.5 8.25 3.0 APDE01400152.0 151.0 145.0 4.0 3.75 2.5 APDE01520160.0 159.0 140.0 8.5 8.25 3.0 APDE01600160.0 159.0 145.0 11.0 10.0 3.0 APDE11600180.0 179.0 160.0 15.0 14.0 3.0 APDE01800200.0 199.0 180.0 8.5 8.25 3.0 APDE02000200.0 199.0 180.0 15.0 14.0 3.0 APDE12000250.0 249.0 230.0 15.0 14.0 3.0 APDE02500Piston Seal - Type APDF19Latest information available at www.tss.trelleborg.comEdition January 2009Piston seal type APDFDescriptionA seal perfectly suited for standard pneumaticapplications and made from a special polyurethane typedeveloped for piston seals.Seal dimensions are in line with cylinder diametersaccording to ISO 3320.Seal design guaranties high reliability and simple snapassembly.The seal has an optimized, stick-slip reducing design foruse in endpositioned damped cylinders with exhaustthrottles.The particular polyurethane offers exceptional wearresistance and extremly high operating performance.Special lip design for pneumatic application to maintainlubrication and minimize friction.Technical dataOperatingpressure: 1.6 MPaSpeed: <=1 m/sTemperature: -35 °C to +85 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonagressive gasesMaterialStandard Material: Zurcon® PU, 83 Shore A,colour grey-blueMaterial No.: Z30InstallationSnap-in installation into closed grooves.It is important to remove all sharp edges and burrs fromthe groove and tube before installation.Ordering examplePiston Seal,type APDFPiston diameter: D = 50 mmGroove width: L = 7.5 mmTSS Part No.: APDF00500 (Table XVIII)Material No.: Z30Material CodeTSS Series No.TSS Article No. 0500Piston diameter x 10APDF Z30-Piston Seal - Type APDF20Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type APDFRmax. 0.2L b120°-30°Bd D1DFigure 5 Installation drawingTable XVIII Installationdimensions / TSS PartNo.BorediameterFlangediameterGroovediameterGroovewidthRingwidthInletchamferTSS Part No.D H10 D1 h10 d h10 L +0.2 B b125.0 24.0 17.0 6.0 5.5 2.0 APDF0025032.0 31.0 24.0 6.0 5.5 2.0 APDF0032040.0 39.0 30.0 7.5 7.0 2.5 APDF0040050.0 49.0 40.0 7.5 7.0 2.5 APDF0050063.0 62.0 53.0 7.5 7.0 2.5 APDF0063080.0 79.0 68.0 9.5 8.5 2.5 APDF00800100.0 99.0 88.0 9.5 8.5 2.5 APDF01000125.0 124.0 110.0 11.0 10.0 3.0 APDF01250Piston Seal - Type APDG21Latest information available at www.tss.trelleborg.comEdition January 2009Piston seal type APDGDescriptionA seal perfectly suited for standard pneumaticapplications and small installation space made from aspecial polyurethane type developed for piston seals.Seal dimensions are in line with cylinder diametersaccording to ISO 3320.Seal design guaranties high reliability and simple snapassembly.This particular polyurethane offers exceptional wearresistance and extremly high operating performance.Special lip design for pneumatic application to maintainlubrication film and minimize friction.The seal has an optimized, stick-slip reducing design foruse in endpositioned damped cylinders with exhaustthrottles.Technical dataOperatingpressure: 1.6 MPaSpeed: <=1 m/sTemperature: -35 °C to +85 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonagressive gasesMaterialStandard Material: Zurcon® PU, 83 Shore A,colour grey-blueMaterial No.: Z30InstallationSnap-in installation into closed grooves.It is important to remove all sharp edges and burrs fromthe groove and tube before installation.Ordering examplePiston Seal,type APDGPiston diameter: D = 50 mmGroove width: L = 3.5 mmTSS Part No.: APDG00500 (Table XIX)Material No.: Z30Material CodeTSS Series No.TSS Article No. 0500Piston diameter x 10Z30-APDG0Piston Seal - Type APDG22Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type APDGBRmax. 0.2L b1d D1D20°-30°Figure 6 Installation drawingTable XIX Installation dimensions / TSS Part No.BorediameterFlangediameterGroovediameterGroovewidthRingwidthInletchamferTSS Part No.D H10 D1 h10 d h10 L +0.2 B b132.0 31.0 24.0 3.5 3.3 2.0 APDG0032040.0 39.0 32.0 3.5 3.3 2.5 APDG0040042.0 41.0 34.0 3.5 3.3 2.5 APDG0042050.0 49.0 42.0 3.5 3.3 2.5 APDG0050063.0 62.0 53.0 4.5 4.3 2.5 APDG0063080.0 79.0 70.0 4.5 4.3 2.5 APDG00800100.0 99.0 90.0 4.5 4.3 2.5 APDG01000Piston Seal - Type APDS23Latest information available at www.tss.trelleborg.comEdition January 2009Piston seal type APDSDescriptionSingle acting piston seal with U-shaped cross-section. Fordouble acting pistons, two seals are used ”back to back”.Same design as APDE-type, but lower interference of thedynamic lip for reduced friction and break-off pressure.Recommended for return spring cylinders. Note: goodguiding system required. Suitable for cylinders withpneumatic cushioning.Technical dataOperatingpressure: 1.6 MPaSpeed: d 1 m/sTemperature: from -40 °C to +80 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonagressive gasesMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationSnap-in installation into closed grooves.It is important to remove all sharp edges and burrs fromthe groove and tube before installation.Ordering examplePiston Seal,type APDSPiston diameter: D = 20 mmGroove width: L = 3 mmTSS Part No.: APDS00200 (Table XX)Material No.: WU9E1Material CodeTSS Series No.TSS Article No. 0200 WU9E1-Piston diameter x 10APDS0Piston Seal - Type APDS24Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type APDSBb1d D1DLR 0.220°-30°Figure 7 Installation drawingTable XX Installation dimensions / TSS Part No.BorediameterFlangediameterGroovediameterGroovewidthRingwidthInletchamferTSS Part No.D H10 D1 h10 d h10 L +0.2 B b16.0 5.0 3.0 2.5 2.0 1.0 APDS000608.0 7.0 4.0 3.0 2.55 1.5 APDS000808.0 7.0 4.0 3.0 2.55 1.5 APDS2008010.0 9.0 6.0 3.0 2.55 1.5 APDS0010012.0 11.0 7.0 3.0 2.55 1.5 APDS0012014.0 13.0 8.0 3.0 2.55 1.5 APDS0014016.0 15.0 10.0 3.0 2.55 2.0 APDS0016017.0 16.0 11.0 3.0 2.55 2.0 APDS0017018.0 17.0 12.0 3.0 2.55 2.0 APDS0018020.0 19.0 14.0 3.0 2.55 2.0 APDS0020025.0 24.0 19.0 3.5 3.25 2.0 APDS0025027.0 26.0 21.0 3.5 3.25 2.0 APDS0027030.0 29.0 22.0 3.5 3.25 2.0 APDS0030032.0 31.0 24.0 3.5 3.25 2.0 APDS0032035.0 34.0 27.0 3.5 3.25 2.0 APDS0035040.0 39.0 32.0 3.5 3.25 2.5 APDS1040050.0 49.0 42.0 3.5 3.25 2.5 APDS0050063.0 62.0 53.0 4.5 4.25 2.5 APDS0063080.0 79.0 70.0 4.5 4.25 2.5 APDS00800100.0 99.0 90.0 4.5 4.25 2.5 APDS01000Piston Seal - Type APMP25Latest information available at www.tss.trelleborg.comEdition January 2009Piston seal type APMPDescriptionSingle acting piston seal with integrated guiding elementand buffer for mechanical cushioning. For double actingpistons, two seals are used ”back to back”. Suitable forshort stroke cylinders and/or magnetic pistons. Themagnet is protected between the piston seals.Technical dataOperatingpressure: 1.6 MPaSpeed: d 1 m/sTemperature: from -40 °C to +80 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonagressive gasesMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationThe installation is done by forced overlapping on thepiston diameter, shaped in a proper way to fit the retainertooth of the seal.Ordering examplePiston Sealtype APMPPiston diameter: D = 32 mmMagnet groove width: t = 3 mmTSS Part No.: APMP00320 (Table XXII)Material No.: WU9E1Material CodeTSS Series No.TSS Article No. 0320 WU9E1-Piston diameter x 10APMP0Piston Seal - Type APMP26Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type APMPtBB2120°bR03.Dd2dq???????????????????????????????????????standard:1Figure 8 Installation drawingTable XXI Installation dimensions / TSS Part No.BorediameterPistonaxialwidthRingwidthMagnetgroovewidthRetainerdeviationCouplingdiameterRetainerdepthMagnetdiameterTSS Part No.D B2 B t b d1h7 q d28.0 12.0 6.0 4.0 4.0 4.0 0.35 6.5 APMP0008010.0 12.0 6.0 3.0 3.5 4.0 0.35 8.5 APMP0010012.0 12.0 6.0 3.0 3.5 6.0 0.40 10.5 APMP0012016.0 12.0 6.0 3.0 3.5 8.0 0.40 14.5 APMP0016020.0 12.0 6.0 3.0 3.5 10.0 0.50 18.0 APMP0020025.0 12.0 6.0 3.0 3.5 10.0 0.50 23.0 APMP00250Piston Seal - Type APMP27Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type APMPtB2120°bDd d1 2qR0.3Bd????????????????????????????????????????????????????????????b2Figure 9 Installation drawingTable XXII Installation dimensions / TSS Part No.BorediameterSealaxialwidthRingwidthMagnetgroovewidthRetainerdeviationProfilewidthPistondiameterRetainerdepthRoddiameterMagnetdiameterTSS Part No.D B2 B t b b2 +0.1 d1h7 q dh7 d232.0 14.0 7.0 3.0 4.0 2.9 26.0 0.5 12.0 29.5 APMP0032032.0 14.0 7.0 5.0 4.0 2.9 26.0 0.5 12.0 29.5 APMP1032040.0 14.5 7.25 5.0 4.25 3.5 34.0 0.5 12.0 37.5 APMP0040050.0 14.5 7.25 5.0 4.25 3.4 43.0 0.6 16.0 46.5 APMP0050063.0 20.0 10.0 5.0 6.0 5.9 55.0 0.8 16.0 59.5 APMP0063080.0 22.0 11.0 5.0 6.5 6.9 72.0 0.8 20.0 76.5 APMP00800100.0 26.0 13.0 5.0 7.5 8.4 90.0 0.8 25.0 96.5 APMP01000Piston Seal - Type APG28Latest information available at www.tss.trelleborg.comEdition January 2009Piston seal type APGDescriptionDouble acting Glyd Ring® piston seal comprising aslipper seal and an energising O-Ring. Speciallydesigned for low friction pneumatic applications withsmall installation space. Suitable for cylinders withpneumatic cushioning. Available for all diameters from 6to 2700 mm.Technical dataOperatingpressure: 1.6 MPa (max. 5 MPa)Speed: <=5 m/sTemperature*: -30 °C ... +200 °C (othertemperature ranges on request)Media: oil free air (initial grease lubricationrecommended), lubricated air,nonagressive gases - depending onthe O-Ring material compatibility.MaterialStandard Material: Zurcon® Z80, ultra-high-molecularweight-polyethylen, 61 Shore D,colour white to off-white.Maximum temperature: 80 °CMaterial No.: Z80N or Z80V *Alternative: Turcon® T19, high grade compo-sition of PTFE resin with mineralfibre intensifier, 62 Shore D,colour dark green-grey.Maximum temperature: 200 °CMaterial No.: T19N or T19V ** depends on O-Ring material (N=NBR / V=FKM)O-Ring material: N7083 NBR 70 Shore A(-30 °C ... +100 °C)V70GA FKM 70 Shore A(-10 °C ... +200 °C)InstallationInstallation into colsed grooves above piston diameter15 mm (above 10 mm for T19).DirectO-Ring installation followedby snap inGlyd Ring®.WhenGlyd Ring® is mounted over a wear ring groove aninstallation sleeve must be used (specimen drawing uponrequest).It is important to remove all sharp edges and burrs fromthe groove and tube before installation.Ordering exampleTurcon Glyd Ring APG complete with O-Ring.Standard application.Series APG from Table XXIIIPiston diameter: DN = 270 mmTSS Part No.: APG802700 from Table XXVSelect the material from Table I.The corresponding code numbers are appended to theTSS Part No. from Table XXV.Together they form the TSS Article number.Other dimensions and all intermediate sizes up to<999.9 mm diameter can be supplied. Fore borediameters >999.9 mm and up to 2.700 mm use thePG46 series Turcon® Glyd Ring®.APG8Material Code (Seal Ring)TSS Series No.TSS Article No. -Type (Standard)*2700 Z80Material Code (O-Ring)N0Bore diameter x 10Quality Index (Standard)* Ordering Turcon® Glyd Ring® with radial notchesplease use suffix “N” in the fifth character.Piston Seal - Type APG29Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type APGFigure 10 Installation drawingTable XXIII Standard installations dimensionsTSS Series No Bore diameterDN H9GroovediameterGroovewidthRadius RadialclearanceSmaxO-RingdiameterStandardrangeAvailableranged1 h8 L1 +0.15 r1 0 - 5 MPa d2APG0 8 - 13.9 6 - 49.9 DN -4.0 2.00 0.5 0.25 1.78APG1 14 - 29.9 10 - 119.9 DN -6.0 2.85 0.5 0.50 2.62APG2 30 - 79.9 15 - 399.9 DN -7.5 3.80 0.8 0.50 3.53APG3 80 - 132.9 40 - 799.9 DN -12.5 5.60 1.3 0.70 5.33APG4 133 - 249.9 110 - 799.9 DN -15.0 7.55 1.5 0.90 7.00APG8 250 - 999.9 150 - 999.9 DN -18.0 7.55 1.5 0.90 7.00For Standard Tube Tolerances H11To extend the availability of cylinder tubes up to a boretolerance of H11 a limited range of diameter areapplicable as per Table XXIV.Table XXIV Alternative installation with boredimensions having tolerance H11 and d1 h8TSS Series No. Bore diameterDN H11Groove diameterAvailable range d1 h8APG0 Not recommended DN - 4.0APG1 Not recommended DN - 6.0APG2 15 - 29.9 DN - 7.5APG3 40 - 179.9 DN -12.5APG4 110 - 179.9 DN - 15.0APG8 150 - 179.9 DN - 18.0r max. 0.3SPressure PressureL1r1d 1DNd 2Piston Seal - Type APG30Latest information available at www.tss.trelleborg.comEdition January 2009Table XXV Installation dimensions / TSS Part No.RodDN H9GrooveDiameterD1 h8GrooveWidthL1 +0.15TSSPart No.O-ringSizes8.0* 4.0 2.00 APG000080 3.68 x 1.789.0* 5.0 2.00 APG000090 4.80 x 18.010.0* 6.0 2.00 APG000100 5.60 x 1.8011.0* 7.0 2.00 APG000110 6.70 x 1.8012.0* 8.0 2.00 APG000120 7.65 x 1.7814.0 8.0 2.85 APG100140 7.59 x 2.6215.0 9.0 2.85 APG100150 9.19 x 2.6216.0* 10.0 2.85 APG100160 9.19 x 2.6218.0* 12.0 2.85 APG100180 10.77 x 2.6219.0* 13.0 2.85 APG100190 12.37 x 2.6220.0* 14.0 2.85 APG100200 13.94 x 2.6222.0* 16.0 2.85 APG100220 15.54 x 2.6224.0 18.0 2.85 APG100240 17.12 x 2.6225.0* 19.0 2.85 APG100250 18.72 x 2.6225.4 19.4 2.85 APG100 4 18.72 x 2.6227.0* 21.0 2.85 APG100270 20.29 x 2.6228.0 22.0 2.85 APG100280 21.89 x 2.6228.0* 20.5 3.80 APG200280 20.22 x 3.5330.0* 22.5 3.80 APG200300 21.82 x 3.5332.0* 24.5 3.80 APG200320 23.40 x 3.5334.0* 26.5 3.80 APG200340 26.58 x 3.5335.0* 27.5 3.80 APG200350 26.58 x 3.5336.0 28.5 3.80 APG200360 28.17 x 3.5337.0* 29.5 3.80 APG200370 28.17 x 3.5338.0* 30.5 3.80 APG200380 29.75 x 3.5340.0* 32.5 3.80 APG200400 31.35 x 3.5342.0* 34.5 3.80 APG200420 34.52 x 3.5343.0* 35.5 3.80 APG200430 34.52 x 3.5344.0* 36.5 3.80 APG200440 36.09 x 3.5345.0 37.5 3.80 APG200450 36.09 x 3.5348.0 40.5 3.80 APG200480 40.87 x 3.5350.0 42.5 3.80 APG200500 40.87 x 3.5350.0* 37.5 5.60 APG300500 37.47 x 5.3350.8 43.3 3.80 APG200508 40.87 x 3.5352.0 44.5 3.80 APG200520 44.04 x 3.5355.0 47.5 3.80 APG200550 47.22 x 3.5355.0* 42.5 5.60 APG300550 40.64 x 5.3357.0 49.5 3.80 APG200570 47.22 x 3.5358.0 50.5 3.80 APG200580 50.39 x 3.5358.0* 45.5 5.60 APG300580 43.82 x 5.3360.0 52.5 3.80 APG200600 51.50 x 3.5560.0* 47.5 5.60 APG300600 46.99 x 5.3362.0 54.5 3.80 APG200620 53.57 x 3.5363.0 55.5 3.80 APG200630 53.57 x 3.5363.0* 50.5 5.60 APG300630 50.17 x 5.33RodDN H9GrooveDiameterD1 h8GrooveWidthL1 +0.15TSSPart No.O-ringSizes65.0 57.5 3.80 APG200650 56.74 x 3.5367.0* 54.5 5.60 APG300670 53.34 x 5.3368.0 60.5 3.80 APG200680 59.92 x 3.5370.0 62.5 3.80 APG200700 59.92 x 3.5370.0* 57.5 5.60 APG300700 56.52 x 5.3372.0* 59.5 5.60 APG300720 56.52 x 5.3375.0 67.5 3.80 APG200750 66.27 x 3.5375.0* 62.5 5.60 APG300750 59.69 x 5.3376.2 68.7 3.80 APG200762 66.27 x 3.5378.0 70.5 3.80 APG200780 69.44 x 3.5380.0* 67.5 5.60 APG300800 66.04 x 5.3382.0* 69.5 5.60 APG300820 69.22 x 5.3382.5 70.0 5.60 APG300825 69.22 x 5.3385.0* 72.5 5.60 APG300850 72.39 x 5.3390.0* 77.5 5.60 APG300900 75.57 x 5.3392.0* 79.5 5.60 APG300920 78.74 x 5.3395.0* 82.5 5.60 APG300950 81.92 x 5.33100.0* 87.5 5.60 APG301000 85.09 x 5.33101.6 89.1 5.60 APG301016 88.27 x 5.33102.0* 89.5 5.60 APG301020 88.27 x 5.33105.0* 92.5 5.60 APG301050 91.44 x 5.33108.0* 95.5 5.60 APG301080 94.62 x 5.33110.0* 97.5 5.60 APG301100 94.62 x 5.33115.0* 102.5 5.60 APG301150 100.97 x 5.33118.0* 105.5 5.60 APG301180 104.14 x 5.33120.0* 107.5 5.60 APG301200 107.32 x 5.33125.0* 112.5 5.06 APG301250 110.49 x 5.33127.0 114.5 5.60 APG301270 113.67 x 5.33130.0 117.5 5.60 APG301300 116.84 x 5.33130.0* 115.0 7.55 APG401300 113.67 x 7.00133.0 118.0 7.55 APG401330 116.84 x 7.00135.0* 120.0 7.55 APG401350 120.02 x 7.00137.0* 122.0 7.55 APG401370 120.02 x 7.00140.0* 125.0 7.55 APG401400 123.19 x 7.00143.0* 128.0 7.55 APG401430 126.37 x 7.00145.0* 130.0 7.55 APG401450 129.54 x 7.00150.0* 135.0 7.55 APG401500 132.72 x 7.00152.4 137.4 7.55 APG401524 135.89 x 7.00153.0* 138.0 7.55 APG401530 135.89 x 7.00155.0* 140.0 7.55 APG401550 139.07 x 7.00160.0* 145.0 7.55 APG401600 142.24 x 7.00165.0* 150.0 7.55 APG401650 148.59 x 7.00170.0* 155.0 7.55 APG401700 151.77 x 7.00175.0 160.0 7.55 APG401750 158.12 x 7.00180.0 165.0 7.55 APG401800 164.47 x 7.0025Piston Seal - Type APG31Latest information available at www.tss.trelleborg.comEdition January 2009RodDN H9GrooveDiameterD1 h8GrooveWidthL1 +0.15TSSPart No.O-ringSizes180.0* 162.0 7.55 APG801800 158.12 x 7.00185.0* 167.0 7.55 APG801850 164.47 x 7.00190.0* 175.0 7.55 APG401900 170.82 x 7.00194.0 179.0 7.55 APG401940 177.17 x 7.00195.0* 177.0 7.55 APG801950 177.17 x 7.00200.0 185.0 7.55 APG402000 183.52 x 7.00200.0* 182.0 7.55 APG802000 177.17 x 7.00203.2 188.2 7.55 APG402032 183.52 x 7.00205.0 190.0 7.55 APG402050 189.87 x 7.00210.0* 192.0 7.55 APG802100 189.87 x 7.00210.0 195.0 7.55 APG402100 189.87 x 7.00215.0 200.0 7.55 APG402150 196.22 x 7.00215.0* 197.0 7.55 APG802150 196.22 x 7.00220.0 205.0 7.55 APG402200 202.57 x 7.00220.0* 202.0 7.55 APG802200 202.57 x 7.00230.0 215.0 7.55 APG402300 215.27 x 7.00240.0 225.0 7.55 APG402400 227.97 x 7.00250.0 232.0 7.55 APG802500 227.97 x 7.00254.0 236.0 7.55 APG802540 227.97 x 7.00255.0 237.0 7.55 APG802550 227.97 x 7.00260.0 242.0 7.55 APG802600 240.67 x 7.00265.0 247.0 7.55 APG802650 240.67 x 7.00268.0 250.0 7.55 APG802680 240.67 x 7.00270.0 252.0 7.55 APG802700 253.37 x 7.00280.0 262.0 7.55 APG802800 253.37 x 7.00290.0 272.0 7.55 APG802900 266.07 x 7.00300.0 282.0 7.55 APG803000 278.77 x 7.00304.8 286.8 7.55 APG803048 278.77 x 7.00310.0 292.0 7.55 APG803100 291.47 x 7.00320.0 302.0 7.55 APG803200 304.17 x 7.00330.0 312.0 7.55 APG803300 304.17 x 7.00350.0 332.0 7.55 APG803500 329.57 x 7.00354.9 336.9 7.55 APG803549 329.57 x 7.00400.0 382.0 7.55 APG804000 380.37 x 7.00425.0 407.0 7.55 APG804250 405.26 x 7.00450.0 432.0 7.55 APG804500 430.66 x 7.00475.0 457.0 7.55 APG804750 456.06 x 7.00500.0 482.0 7.55 APG805000 481.38 x 7.00525.0 507.0 7.55 APG805250 506.86 x 7.00550.0 532.0 7.55 APG805500 532.26 x 7.00575.0 557.0 7.55 APG805750 557.66 x 7.00600.0 582.0 7.55 APG806000 582.68 x 7.00650.0 632.0 7.55 APG806500 633.48 x 7.00700.0 682.0 7.55 APG807000 681.51 x 7.00750.0 732.0 7.55 APG807500 731.51 x 7.00RodDN H9GrooveDiameterD1 h8GrooveWidthL1 +0.15TSSPart No.O-ringSizes800.0 782.0 7.55 APG808000 781.51 x 7.00850.0 832.0 7.55 APG808500 831.51 x 7.00900.0 882.0 7.55 APG809000 881.51 x 7.00950.0 932.0 7.55 APG809500 931.51 x 7.00999.9 981.90 7.55 APG809999 981.41 x 7.00* Standard diameter for Turcon® Glyd Ring® PG59Other dimensions and all intermediate sizes up to999.9 mm diameter can be supplied.For bore diameters>999.9mm andup to 2.700mmusethe RG46 series Turcon® Glyd Ring®.Complete piston - Type AK32Latest information available at www.tss.trelleborg.comEdition January 2009Piston seal type AKDescriptionReady-to-install double acting piston with integratedmetal disc and sealing lips. The rubber cover on the sidesof the metal disc has air channels to ensure pressureapplication on the full piston surface.Technical dataOperatingpressure: 1.2 MPaSpeed: <=1 m/sTemperature: -30 °C ... +100 °C(other temperatureranges on request)Media: oil free air (initial grease lubricationrequired), lubricated air,nonagressive gasesMaterialStandard Material: Material combination NBR 70Shore A / carbon steel 1.0315(fully rubber covered).Material No.: N7MMInstallationReady-to-install piston to be pushed onto the end of therod and fixed with a nut.Ordering examplePiston Sealtype AKBore diameter: D = 63.0 mmOutside diameter: d = 16.0 mmRing width: B = 22 mmTSS Part No.: AK1606322 (Table XXVI)Material No.: N7MMMaterial CodeTSS Series No.TSS Article No. -Piston diameter x 10AK 160 N7MM63 22Bore diam. / Ring widthComplete piston - Type AK33Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type AKD2Bb2tb1ØdØD1ØDFigure 11 Installation dimensionsTable XXVI Range of sizesBorediameterInsiderdiameterRing width Thickness Diameter TSS Article No.D H11 d B b1 b2 t D1 D225.0 8.0 12.0 3.6 6.0 3.0 21.0 16.0 AK080251232.0 8.0 15.0 3.6 6.0 3.0 27.5 16.0 AK080321540.0 10.0 18.0 4.6 7.0 4.0 35.0 23.0 AK100401850.0 10.0 18.0 4.6 7.0 4.0 45.0 25.0 AK100501863.0 16.0 22.0 5.6 8.0 5.0 57.0 40.0 AK160632280.0 16.0 24.0 5.6 8.0 5.0 73.0 55.0 AK1608024100.0 20.0 26.0 6.6 10.0 6.0 92.5 72.0 AK2010026125.0 20.0 26.0 7.4 10.0 6.0 116.0 90.0 AK2012526140.0 22.0 28.0 6.6 10.5 6.0 127.0 100.0 AK2214028160.0 27.0 30.0 9.5 11.5 8.0 149.5 110.0 AK2715030200.0 27.0 35.0 12.0 15.0 10.0 183.0 150.0 AK2720035Sizes other than those listed above can also be manufactured on request.Piston Seal - Type ARS34Latest information available at www.tss.trelleborg.comEdition January 2009Piston seal type ARSDescriptionA seal-scraper perfectly suited for high temperaturepneumatic applications and applications with aggressivemedia, made from FKM as rubber metal bonded seal.The ARS seal-scraper offers exceptionally highoperational performance and strength. The designallows easy assembly into open grooves and is fixed by acirclip.Assembly space equal to ARAA, ARAN and ARV items.Technical dataOperatingpressure: 1.6 MPaSpeed: <= 1 m/sTemperature: -15 °C to + 150 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonagressive gasesMaterialStandard Material: FKM, 75 Shore A, colour brownMaterial No.: VC4VRSpecial elastomer on the basis ofFKM with an integrated vulcanisedsteel supporting disk.A circlip according DIN 7993vers. B for fixing theseal in the groove included indelivery.InstallationInstallation into open groove and fixation with a circlip. Ifthere is a removal notch the ARS-seal-scraper may beexchanged without removing the piston rod.Ordering examplePiston Sealtype ARSRod diameter: D = 50 mmGroove width: L = 10.4 mmTSS Part No.: ARS00500 (Table XXVII)Material No.: VC4VRMaterial CodeTSS Series No.TSS Article No.Piston diameter x 10ARS00 0500 VC4VR-Piston Seal - Type ARS35Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation type ARSBNL1LbfDad D D1R0.2 30°30°rFigure 12 Installation drawingTable XXVII Range of sizesRoddiameterGroove dimensions RingwidthTSS PartNo.d e9 D H10 D1 H10 L1 +0.5 L +0.25 b r a N f B12.0 22.0 24.0 13.0 8.8 2.2 1.1 1.8 4.0 1.5 9.0 ARS00012016.0 26.0 28.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 9.0 ARS00016020.0 30.0 32.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 9.0 ARS00020025.0 35.0 37.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 9.0 ARS00025032.0 42.0 44.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 9.0 ARS00032040.0 50.0 52.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 9.0 ARS00040050.0 60.0 63.2 15.0 10.4 3.6 1.8 2.5 10.0 2.0 9.0 ARS00050063.0 75.0 78.2 16.0 11.4 3.6 1.8 2.5 10.0 2.0 10.0 ARS000630Seal-Scraper - Type AWNS36Latest information available at www.tss.trelleborg.commEdition January 2009Seal-Scraper type AWNSDescriptionAsymmetric lip seal with sealing lip and scraper lip. Smallgroove dimensions and double function allow space andcost savings.Technical dataOperatingpressure: 1.6 MPaSpeed: d 1 m/sTemperature: from -40 °C to +80 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonaggressive gaseMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationInstallation into split grooves or in closed grooves (aboverod diameter 12). It is important to remove all sharpedges and burrs from the groove and rod beforeinstallation.Ordering exampleSeal-scraper,type AWNSRod diameter: d = 20 mmGroove width: L = 7 mmTSS Part No.: AWNS10200 (Table XXVIII)Material No. WU9E1Material CodeTSS Series No.TSS Article No. 0200 WU9E1-Rod diameter x 10AWNS1Seal-Scraper - Type AWNS37Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type AWNSBLDd1DR 0.2aFigure 13 Installation drawingTable XXVIII Installation dimensions / TSS Part No.RoddiameterGroovediameterGroovewidthCouplindiameterRingwidthStepwidthTSS Part No.d f7 D H10 L +0.15 D1 H11 B min a+0.13.0 8.8 4.5 5.0 5.2 1.2 AWNS000304.0 8.8 4.5 6.0 5.2 1.2 AWNS000404.0 7.0 2.7 5.4 2.8 1.0 AWNS100405.0 8.0 2.7 6.2 2.8 1.0 AWNS000506.0 9.0 2.7 7.2 2.8 1.0 AWNS100606.0 10.8 4.5 8.0 5.2 1.2 AWNS000608.0 11.5 3.0 9.2 3.2 1.0 AWNS100808.0 12.8 4.5 10.0 5.2 1.2 AWNS000808.0 14.0 4.5 11.0 5.2 1.2 AWNS2008010.0 14.0 3.2 11.4 3.7 1.0 AWNS1010010.0 16.0 4.0 12.5 4.6 1.0 AWNS2010010.0 16.8 4.5 13.0 5.2 1.2 AWNS0010010.0 18.0 5.0 14.0 6.0 1.6 AWNS3010012.0 16.5 3.7 13.7 4.0 1.2 AWNS4012012.0 18.0 4.0 14.5 4.8 1.2 AWNS0012012.0 20.0 3.7 16.0 5.7 1.6 AWNS6012012.0 20.0 5.0 16.0 6.0 1.6 AWNS1012012.0 20.0 5.5 16.0 6.5 1.6 AWNS2012012.0 22.0 6.0 16.0 6.5 1.5 AWNS3012014.0 18.5 3.7 15.7 4.0 1.2 AWNS2014014.0 20.0 4.0 16.5 4.8 1.2 AWNS0014014.0 22.0 5.0 18.0 6.0 1.5 AWNS30140Seal-Scraper - Type AWNS38Latest information available at www.tss.trelleborg.commEdition January 2009RoddiameterGroovediameterGroovewidthCouplingdiameterRingwidthStepwidthTSS Part No.d f7 D H 10 L +0.15 D1 H11 B min a+0.114.0 24.0 6.0 18.0 6.5 1.5 AWNS1014015.0 22.0 4.0 18.0 5.0 1.5 AWNS0015016.0 20.5 3.7 17.7 4.0 1.2 AWNS2016016.0 22.0 4.0 18.5 5.0 1.2 AWNS0016016.0 24.0 5.0 18.5 6.0 1.5 AWNS3016016.0 26.0 6.0 20.0 6.5 1.5 AWNS1016018.0 22.5 3.7 19.7 4.0 1.2 AWNS1018018.0 24.0 4.0 20.5 5.0 1.4 AWNS2018018.0 26.0 5.0 21.0 6.0 1.6 AWNS3018018.0 28.0 6.0 22.0 6.5 1.5 AWNS0018020.0 25.0 4.0 21.9 4.6 1.2 AWNS2020020.0 26.0 4.0 22.5 4.8 1.2 AWNS0020020.0 30.0 7.0 24.0 7.5 1.5 AWNS1020022.0 27.0 4.0 23.9 4.6 1.2 AWNS0022022.0 28.0 4.0 24.5 5.0 1.4 AWNS1022022.0 32.0 7.0 26.0 7.5 1.5 AWNS2022025.0 30.0 4.0 26.9 4.6 1.2 AWNS2025025.0 31.0 4.0 27.5 4.8 1.2 AWNS0025025.0 35.0 7.0 29.0 7.5 1.5 AWNS1025028.0 38.0 7.0 32.0 7.5 1.5 AWNS0028030.0 35.5 4.55 32.1 5.0 1.2 AWNS1030030.0 38.0 5.0 33.0 5.8 1.5 AWNS2030030.0 40.0 7.0 34.0 7.5 1.5 AWNS0030032.0 37.5 4.55 34.1 5.0 1.2 AWNS2032032.0 40.0 5.0 35.0 5.8 1.3 AWNS1032032.0 42.0 7.0 36.0 7.5 1.5 AWNS0032035.0 45.0 7.0 39.0 7.5 1.5 AWNS0035036.0 44.0 5.0 39.0 6.0 1.3 AWNS0036036.0 46.0 7.0 40.0 7.5 1.5 AWNS1036040.0 46.0 4.9 42.2 5.5 1.4 AWNS1040040.0 50.0 7.0 44.0 7.5 1.5 AWNS0040045.0 53.0 5.0 48.0 6.0 1.3 AWNS0045045.0 55.0 7.0 49.0 7.5 1.5 AWNS1045050.0 62.0 8.5 55.0 9.0 2.0 AWNS0050070.0 80.0 6.0 75.0 7.0 1.5 AWNS00700Seal-Scraper - Type AWSD39Latest information available at www.tss.trelleborg.comEdition January 2009Seal-scraper type AWSDDescriptionAsymmetric lip seal with sealing lip and scraper lip. Smallgroove dimensions and double function allow space andcost savings. Special design facilitates installationespecially for small diameters.Technical dataOperatingpressure: 1.6 MPaSpeed: d 1 m/sTemperature: from -40 °C to +80 °CMedia: oil free air (initial lubricationrequired), lubricated air,nonaggressive gasesMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationInstallation into split grooves or in closed grooves.It is important to remove all sharp edges and burrs fromthe groove and rod before installation.AttentionFor all rod diameters above 20 mm,we recommend onlythe groove design with oversized step (type L1 in Fig.14,page 39).Ordering exampleRod wiper,type AWSDRod diameter: d = 20 mmGroove width: L = 4 mmTSS Part No.: AWSD00200 (Table XXIX)Material No.: WU9E1Material CodeTSS Series No.TSS Article No.Rod diameter x 10AWSD0 0200 WU9E1-Seal-Scraper - Type AWSD40Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type AWSDBL aaL1DD2D D1dR 0.2 R 0.2Figure 14 Installation DrawingTable XXIX Installations dimensions / TSS Part No.RoddiameterGroovediameterGroovewidthGroovewidthToothwidthStepdiameterStepdiameterRingwidthTSS Part No.d e9 D H10 L +0.15 L1+0.15 a+0.1 D1 H11 D2 H11 B4.0 8.1 3 3.8 0.8 6.7 6.1 4.0 AWSD000406.0 11.1 3.6 4.6 1.0 9.1 8.5 5.0 AWSD000608.0 14.1 3.6 4.6 1.0 12.1 11.1 5.0 AWSD0008010.0 16.1 4.2 5.4 1.2 14.1 13.1 6.0 AWSD0010012.0 18.1 4.2 5.4 1.2 15.5 14.9 6.0 AWSD0012012.0 20.0 4.0 6.0 2.0 18.0 15.5 8.0 AWSD1012016.0 24.0 4.0 6.0 2.0 22.0 19.5 8.0 AWSD0016018.0 26.0 4.0 6.0 2.0 24.0 21.5 8.0 AWSD0018020.0 28.0 4.0 6.0 2.0 26.0 23.5 8.0 AWSD0020025.0 33.0 4.0 6.0 2.0 31.0 28.5 8.0 AWSD0025028.0 36.0 4.0 6.0 2.0 34.0 31.5 8.0 AWSD0028030.0 38.0 4.0 6.0 2.0 36.0 33.5 8.0 AWSD1030032.0 40.0 4.0 6.0 2.0 38.0 35.5 8.0 AWSD0032035.0 43.0 4.0 6.0 2.0 41.0 38.5 8.0 AWSD0035036.0 44.0 4.0 6.0 2.0 42.0 39.5 8.0 AWSD0036040.0 48.0 4.0 6.0 2.0 46.0 43.5 8.0 AWSD0040042.0 50.0 4.0 6.0 2.0 48.0 45.5 8.0 AWSD0042045.0 53.0 4.0 6.0 2.0 51.0 48.5 8.0 AWSD0045050.0 58.0 4.0 6.0 2.0 56.0 53.5 8.0 AWSD0050055.0 63.0 4.0 6.0 2.0 61.0 58.5 8.0 AWSD0055056.0 64.0 4.0 6.0 2.0 62.0 59.5 8.0 AWSD00560Seal-Scraper - Type AWSD41Latest information available at www.tss.trelleborg.comEdition January 2009RoddiameterGroovediameterGroovewidthGroovewidthStepwidthCouplingdiameterCouplingdiameterRingwidthTSS Part No.d e9 D H10 L +0.15 L1 +0.15 a+0.1 D1 H11 D2 H11 B60.0 68.0 4.0 6.0 2.0 66.0 63.5 8.0 AWSD0060063.0 71.0 4.0 6.0 2.0 69.0 66.5 8.0 AWSD0063065.0 73.0 4.0 6.0 2.0 71.0 68.5 8.0 AWSD0065070.0 78.0 4.0 6.0 2.0 76.0 73.5 8.0 AWSD0070075.0 83.0 4.0 6.0 2.0 81.0 78.5 8.0 AWSD0075080.0 88.0 4.0 6.0 2.0 86.0 83.5 8.0 AWSD0080085.0 93.0 4.0 6.0 2.0 91.0 88.5 8.0 AWSD0085090.0 98.0 4.0 6.0 2.0 96.0 93.5 8.0 AWSD00900100.0 108.0 4.0 6.0 2.0 106.0 103.5 8.0 AWSD01000Seal-Scraper - Type ARAA42Latest information available at www.tss.trelleborg.comEdition January 2009Seal-Scraper type ARAADescriptionRod seal-scraper with integrated fixing capability.Compared to ARAN improved in seal-lip design for bettersealing and scraping performance. Very good protectionagainst dirt ingress.Assembly space equal to ARAN, ARS and ARV items.This particular polyurethane offers exceptional wearresistance and extremly high operating performance.Special lip design for pneumatic application to maintainlubricating film and minimize friction.For high humidity applications an alternative materialwith improved hydrolysis resistance is available.Technical dataOperatingpressure: 1.6 MPaSpeed: <= 1 m/sTemperature: -35 °C to + 110 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonagressive gasesMaterialStandard Material: Zurcon® PU, 94 Shore A,colour turquoiseMaterial No.: Z20InstallationThe ARAA-seal-scraper snaps into a special groove.Separate fixing elements are not neccessary. It isimportant to remove all sharp edges from the groove andshaft to prevent damaging the seal / seal lips.Note: Avoidgrease on outer diameter and groove.Ordering examplePiston Sealtype ARAARod diameter: D = 20 mmGroove width: L = 8.8 mmTSS Part No.: ARAA00200 (Table XXX)Material No.: Z20Material CodeTSS Series No.TSS Article No.Piston diameter x 10ARAA0 0200 Z20-Seal-Scraper - Type ARAA43Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type ARAANLbfBL1Dd1DDraR 0.230°30°Figure 15 Installation drawingTable XXX Range of sizesRoddiameterGroove dimensions RingwidthTSS PartNo.d e9 D H10 D1 H10 L1 +0.5 L +0.25 b r a N f B12.0 22.0 24.0 13.0 8.8 2.2 1.1 1.8 4.0 1.5 10.7 ARAA1012016.0 26.0 28.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARAA0016020.0 30.0 32.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARAA0020025.0 35.0 37.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARAA0025032.0 42.0 44.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARAA00320Seal-Scraper - Type ARAN44Latest information available at www.tss.trelleborg.comEdition January 2009Seal-Scraper type ARANDescriptionAsymmetric lip seal with sealing lip and scraper lip. Verygood protection against dirt ingress. Special groove andseal design allows fast installation either automatically ormanually.Assembly space equal to ARAA, ARS and ARV items.Technical dataOperatingpressure: 1.6 MPaSpeed: d 1 m/sTemperature: from -40 °C to +80 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonaggresive gasesMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationThe ARAN-seal-scraper snaps into a special groove.Separate fixing elements are not neccessary. It isimportant to remove all sharp edges from the groove andshaft to prevent damaging the seal / seal lips.Note: Avoidgrease on outer diameter and groove.Ordering exampleRod wiper,type ARANRod diameter: d = 20 mmGroove width: L = 8.8 mmTSS Part No.: ARAN00200 (Table XXXI)Material No.: WU9E1Material No.:TSS Series No.TSS Article No. 0200 WU9E1-Rod diameter x 10ARAN0Seal-Scraper - Type ARAN45Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation type ARANNLbfBL1Dd1DDraR 0.230°30°Figure 16 Installation drawingTable XXXI Installation dimensions / TSS Part No.Roddia-meterGroove dimensions RingwidthTSS Part No.d e9 D H10 D1 H10 L1+0.5 L+0.25 b r a N f B12.0 20.0 22.0 13.0 8.8 2.2 1.1 1.8 4.0 1.5 10.7 ARAN0012012.0 22.0 24.0 13.0 8.8 2.2 1.1 1.8 4.0 1.5 10.7 ARAN1012016.0 26.0 28.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARAN0016018.0 26.0 28.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARAN0018018.0 28.0 30.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARAN1018020.0 30.0 32.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARAN0020022.0 32.0 34.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARAN0022025.0 35.0 37.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARAN0025030.0 40.0 42.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARAN0030032.0 42.0 44.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARAN0032040.0 50.0 52.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARAN0040045.0 55.0 58.2 15.0 10.4 3.6 1.8 2.5 10.0 2.0 12.2 ARAN0045050.0 60.0 63.2 15.0 10.4 3.6 1.8 2.5 10.0 2.0 12.2 ARAN00500Scraper - Type AWSW46Latest information available at www.tss.trelleborg.comEdition January 2009Scraper type AWSWDescriptionSingle acting scraper for use with separate rod seal.Special lip design for pneumatic application to maintainrod lubrication.Technical dataOperatingpressure: -Speed: d 1 m/sTemperature: from -40 °C to +80 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonaggressive gasesMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationIn split grooves or in closed grooves.It is important to remove all sharp edges and burrs fromthe groove and rod before installation.Ordering exampleRod wiper,type AWSWRod diameter: d = 20 mmGroove width: L = 4 mmTSS Part No.: AWSW00200 (Table XXXII)Material No.: WU9E1Material code:TSS Series No.TSS Article No. 0200 WU9E1-Rod diameter x 10AWSW0Scraper - Type AWSW47Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type AWSWLBad D D1R 0.2Figure 17 Installation drawingTable XXXII Installation dimensions / TSS Part No.RoddiameterGroovediameterGroovewidthCouplingdiameterStepwidthRingwidthTSS Part No.d f7 D H11 L +0.15 D1 H11 a min. B6.0 10.0 2.0 8.0 1.0 4.0 AWSW000608.0 14.0 2.5 12.0 1.0 5.0 AWSW0008010.0 18.0 4.0 16.0 1.0 7.0 AWSW0010010.0 16.0 2.5 14.0 1.0 5.0 AWSW1010012.0 20.0 4.0 18.0 1.0 7.0 AWSW0012012.0 18.0 2.5 16.0 1.0 5.0 AWSW1012014.0 22.0 4.0 20.0 1.0 7.0 AWSW0014014.0 20.0 2.5 18.0 1.0 5.0 AWSW1014016.0 24.0 4.0 22.0 1.0 7.0 AWSW0016018.0 26.0 4.0 24.0 1.0 7.0 AWSW0018020.0 28.0 4.0 26.0 1.0 7.0 AWSW0020022.0 30.0 4.0 28.0 1.0 7.0 AWSW0022025.0 33.0 4.0 31.0 1.0 7.0 AWSW0025028.0 36.0 4.0 34.0 1.0 7.0 AWSW0028030.0 38.0 4.0 36.0 1.0 7.0 AWSW0030032.0 40.0 4.0 38.0 1.0 7.0 AWSW0032035.0 43.0 4.0 41.0 1.0 7.0 AWSW0035038.0 46.0 4.0 44.0 1.0 7.0 AWSW0038040.0 48.0 4.0 46.0 1.0 7.0 AWSW0040045.0 53.0 4.0 51.0 1.0 7.0 AWSW0045050.0 58.0 4.0 56.0 1.0 7.0 AWSW0050055.0 63.0 4.0 61.0 1.0 7.0 AWSW0055060.0 68.0 4.0 66.0 1.0 7.0 AWSW00600Wipers for guiding units - Type AWBB48Latest information available at www.tss.trelleborg.comEdition January 2009Wipers for guiding units, type AWBBDescriptionWiper specially designed for guide units with linear ballbearings. Wiper lip with minimal pre-load to avoidnegative influences on the sliding behaviour of the guideunit. The outer diameter is designed for fixing by astandard circlip retainer groove.The installation dimensions correspond to the housingdiameter of the ball bearing.Technical dataOperatingpressure: -Speed: <= 4 m/sTemperature: from -40 °C to +80 °CMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationInstallation by snapping the fixing collar into a standardcirclip retainer groove.It is important to remove all sharp edges and burrs fromthe groove and rod before installation.Ordering exampleWiper,type AWBBRod diameter: d = 20 mmGroove width: L = 1.6 mmTSS Part No.: AWBB00200 (Table XXIII)Material No.: WU9E1Material code:TSS Series No.TSS Article No. 0200 WU9E1-Rod diameter x 10AWBB0Wipers for guiding units - Type AWBB49Latest information available at www.tss.trelleborg.comEdition January 2009guide unit withlinear ball bearingBØdØd1Ød2LL1Rmax.0.2Figure 18 Installation drawingTable XXXIII Range of sizesRoddiameterGroove dimensions RingwidthTSS Part No.d e9 d1 H10 d2 H10 L1 +0.1 L +0.1 B8.0 15.0 17.6 3.0 1.6 4.5 AWBB0008010.0 17.0 19.6 3.0 1.6 4.5 AWBB0010012.0 19.0 21.6 3.0 1.6 4.5 AWBB0012014.0 21.0 23.6 3.0 1.6 4.5 AWBB0014016.0 24.0 26.6 3.0 1.6 4.5 AWBB0016020.0 28.0 30.6 3.0 1.6 4.5 AWBB0020025.0 35.0 37.6 3.0 1.6 4.5 AWBB0025030.0 40.0 42.6 3.0 1.6 4.5 AWBB0030040.0 52.0 54.6 3.0 1.6 4.5 AWBB00400Seal-Scraper - Type ARV50Latest information available at www.tss.trelleborg.comEdition January 2009Seal-Scraper type ARVDescriptionAsymmetric Variseal® type seal with spring energizedsealing lip and scraper lip. Suitable for poor lubrication,high speed or foodstuff application (FDA compliant). Verygood protection against dirt ingress. (Hi-Clean versionavailable where the spring cavity of the scraper lip is filledwith a Silicone gel preventing contaminants from beingentrapped.)Special groove and seal design allows fast installationeither automatically or manually.Technical dataOperatingpressure: 1.6 MPaSpeed: <= 5 m/sTemperature: -30 °C to +80 °Cother temperatureranges on requestMedia: oil free air with or without initialgrease lubrication, lubricated air,nonaggressive gases, foodstuffMaterialStandard Material: Ultra-high-molecularweight-polyethylene, 52 Shore D,colour white to off whiteMaterial No.: Z80SV-spring: standard materials AISI 301InstallationSnap-in installation into open grooves.It is important to remove all sharp edges and burrs fromthe groove and rod before installation. Note: Inletchamfer on rod and bore diameter required.Ordering exampleRod wiper,type ARVRod diameter: d = 20 mmGroove width: L = 8.8 mmTSS Part No.: ARV00200 (Table XXXIV)Material No.: Z80SMaterial No.:TSS Series No.TSS Article No. 0200 -Rod diameter x 10ARV00 Z80SMaterial code for springSeal-Scraper - Type ARV51Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation type ARVBN LL1bfDad D D1R0.2 30°30°rFigure 20 Installation drawingTable XXXIV Installation dimensions / TSS Part No.RoddiameterGroove dimensions RingwidthTSS Part No.d e9 D H10 D1 H10 L1+0.5 L+0.25 b r a N f B10.0 18.0 20.0 12.0 7.7 2.2 1.1 1.8 4.0 1.5 10.7 ARV00010012.0 20.0 22.0 13.0 8.8 2.2 1.1 1.8 4.0 1.5 10.7 ARV00012012.0 22.0 24.0 13.0 8.8 2.2 1.1 1.8 4.0 1.5 10.7 ARV01012014.0 24.0 26.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARV00014016.0 26.0 28.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARV00016018.0 26.0 28.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARV00018018.0 28.0 30.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARV01018020.0 30.0 32.0 13.0 8.8 2.2 1.1 1.8 5.0 1.5 10.7 ARV00020022.0 32.0 34.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARV00022025.0 35.0 37.5 14.0 9.4 2.8 1.4 2.0 7.5 2.0 11.2 ARV000250Cushioning Seal - Type AICM52Latest information available at www.tss.trelleborg.comEdition January 2009Cushioning seal, type AICMDescriptionThe cushioning seal AICM is designed especially forpneumatic cushioning where high pressure peaks occur.Effective cushioning due to lip sealing with inlet chamfer.After change of pressure direction, the integrated checkvalve function ensures pressure application on the fullpiston surface.Technical dataOperatingpressure: 1.6 MPaSpeed: d 1 m/sTemperature: Z20 -35 °C to +110 °CWU9E1 -40 °C to +80 °CMedia: oil free air (initial grease lubricationrequired), lubricated air,nonaggressive gasesMaterialStandard: Zurcon® PU, 94 Shore A,colour turquoiseMaterial No.: Z20* Available dimensions on request.Alternative: Standard polyurethane with fairperformance level.Polyurethane, 90 Shore A,Material No.: WU9E1InstallationSnap-in installation into closed grooves.It is important to remove all sharp edges and burrs fromthe groove and rod before installation.Ordering exampleCushioning seal,type AICMRod diameter: d = 20 mmGroove width: L = 7 mmTSS Part No.: AICM00200 (Table XXXV)Material No.: Z20Material CodeTSS Series No.TSS Article No. 0200 -Rod diameter x 10AICM0 Z20Cushioning Seal - Type AICM53Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type AICMLbBmin. 2 mmdDD2D1R 230°R 0.2d1Figure 21 Installation drawingTable XXXV Installation dimensions / TSS Part No.Rod diameter Groove dimensions Ring width TSS Part No.d h10 D H11 D1 H11 D2 H11 L r0.1 d1 h11 b +0.2 B6.0 10.0 6.5 8.0 3.7 4.5 2.0 4.0 AICM000608.0 11.6 8.5 10.0 3.3 7.0 2.0 3.5 AICM000809.5 15.0 10.0 12.0 4.5 8.0 2.0 4.5 AICM0009510.0 18.0 11.0 15.0 7.0 8.0 2.0 7.8 AICM0010012.0 18.0 13.0 15.5 4.8 10.0 2.0 5.0 AICM1012012.0 20.0 13.0 17.0 7.0 10.0 2.0 7.8 AICM0012014.0 22.0 15.0 19.0 7.0 12.0 2.0 7.8 AICM0014016.0 22.0 17.0 19.5 5.2 14.0 2.0 5.5 AICM1016016.0 24.0 17.0 21.0 7.0 14.0 2.0 7.8 AICM0016018.0 26.0 19.0 23.0 7.0 16.0 2.0 7.8 AICM0018020.0 28.0 21.0 24.0 7.0 17.5 2.0 7.8 AICM0020022.0 30.0 23.0 26.0 7.0 19.5 2.0 7.8 AICM0022025.0 33.0 26.0 29.0 7.0 22.5 2.0 7.8 AICM0025028.0 36.0 29.0 32.0 7.0 25.5 2.0 7.8 AICM0028030.0 40.0 31.5 35.0 7.0 27.5 2.0 7.8 AICM0030032.0 42.0 33.5 37.0 7.0 29.0 2.0 7.8 AICM0032036.0 46.0 37.5 41.0 7.0 33.0 2.0 7.8 AICM0036040.0 50.0 41.5 45.0 7.0 37.0 2.0 7.8 AICM0040050.0 60.0 51.5 55.0 7.0 47.0 2.0 7.8 AICM0050057.0 74.0 60.0 65.0 12.5 54.0 2.0 11.0 AICM00570Cushioning Seal - Type AIAS54Latest information available at www.tss.trelleborg.comEdition January 2009Cushioning Seal, type AIASDescriptionThe cushioning seal AIAS is designed especially forpneumatic cushioning where high pressure peaks occur.Small groove dimensions to replace O-rings. Afterchange of pressure direction, the integrated check valvefunction ensures pressure application on the full pistonsurface.Technical dataOperatingpressure: 1.6 MPaSpeed: d 1 m/sTemperature: from -40 °C to +80 °CMedia: oil free air (initial grease lubricationrequired), lubeicated air,nonaggressive gasesMaterialStandard polyurethane with fair performance level.Standard Material: Polyurethane, 90 Shore A,Material No.: WU9E1InstallationSnap-in installation into closed grooves.It is important to remove all sharp edges and burrs fromthe groove and rod before installation.Ordering exampleCushioning seal,type AIASRod diameter: d = 50 mmGroove width: L = 6 mmTSS Part No.: AIAS00500 (Table XXXVI)Material No.: WU9E1Material CodeTSS Series No.TSS Article No. 0500 WU9E1-Rod diameter x 10AIAS0Cushioning Seal - Type AIAS55Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, type AIASLmin. 2 mmbdDD2d1D1WR 230°R 0.2Figure 22 Installation drawingTable XXXVI Installation dimensions / TSS Part No.Rod diameter Groove dimensions Ring width TSS Part No.d h10 D H11 D1 H11 D2 H11 L r0.1 d1 h11 b +0.2 W10.0 18.0 10.5 12.0 4.8 7.0 2.0 4.0 AIAS0010012.0 20.0 12.5 14.0 4.8 9.0 2.0 4.0 AIAS0012014.0 22.0 14.5 16.0 4.8 11.0 2.0 4.0 AIAS0014016.0 24.0 16.5 18.0 4.8 13.0 2.0 4.0 AIAS0016018.0 26.0 18.5 20.0 4.8 15.0 2.0 4.0 AIAS0018020.0 28.0 20.5 22.0 4.8 17.0 2.0 4.0 AIAS0020022.0 30.0 22.5 24.0 4.8 18.0 2.0 4.0 AIAS0022025.0 33.0 25.5 27.0 4.8 21.0 2.0 4.0 AIAS0025030.0 40.0 30.6 32.0 6.0 26.0 2.0 5.0 AIAS0030032.0 42.0 32.6 34.0 6.0 28.0 2.0 5.0 AIAS0032035.0 45.0 35.6 37.0 6.0 31.0 2.0 5.0 AIAS0035036.0 46.0 36.6 38.0 6.0 32.0 2.0 5.0 AIAS0036040.0 50.0 40.6 42.0 6.0 36.0 2.0 5.0 AIAS0040050.0 60.0 50.6 52.0 6.0 46.0 2.0 5.0 AIAS00500Wear Ring56Latest information available at www.tss.trelleborg.comEdition January 2009Wear ring in modified POM for piston and rodDescriptionThe wear ring has the twin function of guiding the pistonor the rod in a cylinder and of absorbing transversalforces in it.At the same time, the metal contact between the slidingparts of the cylinder (piston and bore or cylinder rod andcylinder head) must be avoided.The wear ring in modified POM material has beenspecifically designed for the use on such pneumaticcylinders.The ring is available for a wide range of standarddimensions (see tables XXXIX and XXXXIII, page 56 and 59).Other dimensions are available on request.The TSS Serial No. for wear rings in modified POM arelisted in the following table.Table XXXVII TSS Serial numbers for injectionmolded wear rings in modified POMPiston Rod Groove RingPistonTSS Serial No.RodTSS Serial No.GroovewidthRingthicknessTSS Serial No. TSS Serial No. widthL2thicknessWGP41 GR41 2.50 1.55GP43 GR43 4.00 1.55GP48 GR48 8.20 2.00GP49 GR49 9.70 2.00GP51 GR51 10.00 2.00GP53 GR53 15.00 2.00GP54 GR54 20.00 2.00GP55 GR55 25.00 2.00GP56 GR56 30.00 2.00Other materials and dimensions available - see also”Hydraulic catalogue chapt. Slydrings” or ask TSS.All wear guide rings have chamfered edges, in order toavoid undesired edge forces in the corner radii of thegrooves.The choice for the correct size of the ring can be based onthe following formula:F x fh = ———d x pwhere the meaning of the letters are the following:p = admissible pressureF = radial loadf = safety factord = average guide diameterh = guide widthMaterialPOTBWThis compound in polyacetal was specifically formulatedfor pneumatic cylinders made in aluminium.Advantages:H Good price/performance ratioH High compressive strengthH Very good sliding effect in dry conditionsH Good resistance to abrasionH Low stick-slip effectH Simple installation also in closed groovesH Long lifeWear Ring57Latest information available at www.tss.trelleborg.comEdition January 2009Fields of applicationSpeed: Up to 1 m/s, with reciprocatingmovements.Temperature: from -40 °C to +110 °CCalculation value:Static compressivestrength: max. 36.3 N/mm2 at roomtemperature.The load capacity for dynamic applicationsmost dependson the operating temperature, which, therefore, shouldnot exceed 90 °C.Wear Ring58Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, wear ring for piston2LDS2D1WR maxZFigure 23 Installation drawingTable XXXVIII Installation dimensionsTSS Serial No. Borediameter1)GroovediameterGroovewidthRadialclearanceRingthicknessRinggapD H9 D2 h8 L2+0.2 S12) W ZGP41 8 - 20,0 D -3.10 2,50 0.20 - 0.30 1.55 1 - 3GP43 10 - 50.0 D -3.10 4.00 0.20 - 0.40 1.55 2 - 4GP48 20 - 40.0 D -4.00 8.20 0.20 - 0.40 2.00 1 - 3GP49 16 - 20.0 D -4.00 9.70 0.20 - 0.50 2.00 1 - 3GP51 45 - 70.0 D -4.00 10.00 0.30 - 0.50 2.00 1 - 3GP53 75 - 100.0 D -4.00 15.00 0.30 - 0.50 2.00 1 - 3GP54 105 - 140.0 D -4.00 20.00 0.30 - 0.50 2.00 2 - 4GP55 150 - 200.0 D -4.00 25.00 0.30 - 0.60 2.00 3 - 5GP56 220 - 250.0 D -4.00 30.00 0.30 - 0.60 2.00 4 - 61) Recommended diameter ranges 2) Specifications valid only in the area of the wear rings.Table XXXIX Recommended radii forgroove diameterD R max.8 -250 0.2>250 0.4Table XXXX Surface roughnessParameter Matingsurface PmGroovesurface PmR max. 1.00 - 4.00 < 16.0RZ DIN 0.63 - 2.50 < 10.0Ra 0.10 - 0.40 < 2.5Wear Ring59Latest information available at www.tss.trelleborg.comEdition January 2009Table XXXXI Wear ring for pistonBorediameterGroovediameterGroovewidthThickness TSS Part No.D H9 D2 h8 L2+0.2 W8.0 4.9 2.5 1.55 GP410008010.0 6.9 2.5 1.55 GP410010010.0 6.9 4.0 1.55 GP430010012.0 8.9 4.0 1.55 GP430012014.0 10.9 4.0 1.55 GP430014015.0 11.9 4.0 1.55 GP430015016.0 12.9 4.0 1.55 GP430016016.0 12.0 9.7 2.00 GP490016018.0 14.9 4.0 1.55 GP430018018.0 14.0 9.7 2.00 GP490018020.0 16.9 4.0 1.55 GP430020020.0 16.0 8.2 2.00 GP480020020.0 16.0 9.7 2.00 GP490020022.0 18.0 9.7 2.00 GP490022025.0 21.9 4.0 1.55 GP430025025.0 21.0 8.2 2.00 GP480025030.0 26.0 8.2 2.00 GP480030032.0 28.9 4.0 1.55 GP430032032.0 28.0 8.2 2.00 GP480032035.0 31.0 8.2 2.00 GP480035040.0 36.0 8.2 2.00 GP480040045.0 41.0 10.0 2.00 GP510045050.0 46.0 9.7 2.00 GP490050050.0 46.0 10.0 2.00 GP510050055.0 51.0 9.7 2.00 GP490055055.0 51.0 10.0 2.00 GP510055058.0 54.0 10.0 2.00 GP510058060.0 56.0 9.7 2.00 GP490060060.0 56.0 10.0 2.00 GP510060063.0 59.0 10.0 2.00 GP510063065.0 61.0 9.7 2.00 GP490065065.0 61.0 10.0 2.00 GP510065070.0 66.0 10.0 2.00 GP510070075.0 71.0 9.7 2.00 GP490075075.0 71.0 15.0 2.00 GP530075080.0 76.0 9.7 2.00 GP490080080.0 76.0 10.0 2.00 GP510080080.0 76.0 15.0 2.00 GP530080085.0 81.0 9.7 2.00 GP490085085.0 81.0 15.0 2.00 GP530085090.0 86.0 15.0 2.00 GP530090095.0 91.0 15.0 2.00 GP5300950100.0 96.0 9.7 2.00 GP4901000100.0 96.0 10.0 2.00 GP5101000100.0 96.0 15.0 2.00 GP5301000Wear Ring60Latest information available at www.tss.trelleborg.comEdition January 2009BorediameterGroovediameterGroovewidthThickness TSS Part No.D H9 D2 h8 L2+0.2 W105.0 101.0 20.0 2.00 GP5401050110.0 106.0 20.0 2.00 GP5401100115.0 111.0 20.0 2.00 GP5401150120.0 116.0 20.0 2.00 GP5401200125.0 121.0 15.0 2.00 GP5301250125.0 121.0 20.0 2.00 GP5401250130.0 126.0 20.0 2.00 GP5401300135.0 131.0 20.0 2.00 GP5401350140.0 136.0 20.0 2.00 GP5401400150.0 146.0 25.0 2.00 GP5501500160.0 156.0 15.0 2.00 GP5301600180.0 176.0 25.0 2.00 GP5501800200.0 196.0 20.0 2.00 GP5402000200.0 196.0 25.0 2.00 GP5502000220.0 216.0 30.0 2.00 GP5602200250.0 246.0 20.0 2.00 GP5402500250.0 246.0 30.0 2.00 GP5602500Ordering exampleWear ring for piston, diameter D = 20.00 mmSeries GP49 from Table XXXVIII, page 58Groove width: 9.70 mm, ring thickness: 2.00 mmMaterial: POTBWTSS Article No.: GP4900200(from Table XXXXI, page 59)Material code:TSS Series No.TSS Article No. 0200Piston diameter x 10GP49 0Design code (standard)POTBWFor all intermediate dimensions not listed in table XXXIX,the TSS Article No. can be formed from the example.Wear Ring61Latest information available at www.tss.trelleborg.comEdition January 2009Installation recommendation, wear ring for rodL2dS2dW1RmaxZFigure 24 Installation drawingTable XXXXII Installation dimensionsTSS Serial No. Roddiameter1)GroovediameterGroovewidthRadialclearanceRingthicknessRinggapd f8/h9 d2 H8 L2+0.2 S12) W ZGR41 8 - 20.0 d +3.10 2.50 0.20 - 0.30 1.55 1 - 3GR43 10 - 50.0 d +3.10 4.00 0.20 - 0.40 1.55 2 - 4GR49 16 - 20.0 d +4.00 9.70 0.20 - 0.50 2.00 1 - 31) Recommended diameter ranges 2) Specifications valid only in the area of the wear ringsTable XXXXIII Recommended radiifor groove diameterD R max.8 -250 0.2>250 0.4Table XXXXIV Surface roughnessParameter Matingsurface PmGroovesurface PmR max. 1.00 - 4.00 < 16.0RZ DIN 0.63 - 2.50 < 10.0Ra 0.10 - 0.40 < 2.5Wear Ring62Latest information available at www.tss.trelleborg.comEdition January 2009Table XXXXV Wear ring for rodRod diameter Groove diameter Groove width thickness TSS Part No.d f8/h9 d2 H8 L2 +0.2 W8.0 11.1 2.5 1.55 GR410008010.0 13.1 2.5 1.55 GR410010010.0 13.1 4.0 1.55 GR430010012.0 15.1 4.0 1.55 GR430012012.0 16.0 9.7 2.00 GR490012014.0 17.1 4.0 1.55 GR430014014.0 18.0 9.7 2.00 GR490014015.0 18.1 4.0 1.55 GR430015016.0 19.1 4.0 1.55 GR430016016.0 20.0 9.7 2.00 GR490016018.0 21.1 4.0 1.55 GR430018018.0 22.0 9.7 2.00 GR490018020.0 23.1 4.0 1.55 GR430020022.0 25.1 4.0 1.55 GR430022025.0 28.1 4.0 1.55 GR430025028.0 31.1 4.0 1.55 GR430028030.0 33.1 4.0 1.55 GR430030032.0 35.1 4.0 1.55 GR430032035.0 38.1 4.0 1.55 GR430035035.0 39.0 9.7 2.00 GR490035036.0 39.1 4.0 1.55 GR430036040.0 43.1 4.0 1.55 GR430040040.0 44.0 9.7 2.00 GR490040045.0 49.0 9.7 2.00 GR490045046.0 60.0 9.7 2.00 GR490046050.0 53.1 4.0 1.55 GR430050050.0 54.0 9.7 2.00 GR490050055.0 59.0 9.7 2.00 GR490055060.0 64.0 9.7 2.00 GR4900600Wear Ring63Latest information available at www.tss.trelleborg.comEdition January 2009Ordering exampleWear ring for rod, diameter d = 16.00 mmSeries GR43 from Table XXXXII, page 61Groove width: 4.00 mm, ring thickness: 1.55 mmMaterial: POTBWTSS Article No.: GR4300160 (from Table XXXXV, page 62)Material code:TSS Series No.TSS Article No. 0160Rod diameter x 10GR43 0Design code (standard)POTBWFor all intermediate dimensions not listed in table XXXXIII,the TSS Article No. can be formed from the example.Static Seal - Type DRV464Latest information available at www.tss.trelleborg.comEdition January 2009Static Seal type DRV4DescriptionThe DRV4-seal is a static operating seal ring developedfor pneumatic applications.It is a 2-component-injection-molding part (plastics /polyurethane).DRV4-seal is conform according ISO 16030 andachieves the following properties:- captive on thread (triple-lug principle)- reusable (up to 5 - 10 x)- capable of providing long-term performanceIn addition DRV4 offers more advantages:- close by hand-torque- no corrosion, because plasitcs-polyurethane-bonded- long-time tight- excellent automatically mountable- lightweightTechnical dataOperatingpressure: 1.0 MPaTemperature: -10 °C to +60 °CMaterialbasic ring: PA, greyseal: TPU, blackInstallationThe seal has only to be fitted on the threaded bolt. If thebolted connection is tightened the sealing lip is pressedagainst the flat surfaces. The thickness of the basic ringlimits the compression of the elastomer seal. Sealingeffects will already be achieved by hand-torque.Ordering exampleStatic Seal,type DRV4Thread diameter: 1/2 ”TSS Part No.: DRV401270 (Table XXXXVI)Material No.: U8XPAMaterial No.:TSS Series No.TSS Article No. -DimensionDRV4 U8XPA01270outside diameterinside diameterthicknessFigure 25Further solutions for static applications:Please see also O-Ring catalogue or Static Sealcatalogue.Static Seal - Type DRV465Latest information available at www.tss.trelleborg.comEdition January 2009Table XXXXVISize Inside diameter Outside diameter Thickness TSS Article No.1/8 inch 9.90 mm +0.05/-0.05 13.15 mm +0.05/-0.05 1.60 mm +0.05/-0.05 DRV400990-U8XPA1/4 inch 13.30 mm +0.05/-0.05 18.15 mm +0.05/-0.05 2.20 mm +0.05/-0.05 DRV401330-U8XPA3/8 inch 16.80 mm +0.05/-0.05 22.15 mm +0.05/-0.05 2.20 mm +0.05/-0.05 DRV401680-U8XPA1/2 inch 21.20 mm +0.05/-0.05 26.45 mm +0.05/-0.05 2.35 mm +0.05/-0.05 DRV402120-U8XPA3/4 inch 26.70 mm +0.05/-0.05 32.45 mm +0.05/-0.05 2.95 mm +0.05/-0.05 DRV402670-U8XPAYour Partner for Sealing TechnologyTrelleborg Sealing Solutions is a major international sealing force, uniquely placed to offer dedicated design and development from our market-leading product and material portfolio: a one-stop-shop providing the best in elastomer, thermoplastic, PTFE and composite technologies for applications in aerospace, industrial and automotive industries.With 50 years of experience, Trelleborg Sealing Solutions engineers support customers with design, prototyping, production, test and installation using state-of-the-art design tools. An international network of over 70 facilities worldwide includes over 20 manufacturing sites, strategically-positioned research and development centers, including materials and development laboratories and locations specializing in design and applications.Developing and formulating materials in-house, we utilize the resource of our material database, including over 2,000 proprietary compounds and a range of unique products.Trelleborg Sealing Solutions ful?lls challenging service requirements, supplying standard parts in volume or a single custom-manufactured component, through our integrated logistical support, which effectively delivers over 40,000 sealing products to customers worldwide.Facilities are certi?ed to ISO 9001:2008 and ISO/TS 16949:2009. Trelleborg Sealing Solutions is backed by the experiences and resources of one of the world‘s foremost experts in polymer technology: the Trelleborg Group.The information in this brochure is intended to be for general reference purposes only and is not intended to be a speci?c recommendation for any individual application. The application limits for pressure, temperature, speed and media given are maximum values determined in laboratory conditions. In application, due to the interaction of operating parameters, maximum values may not be achieved. It is vital therefore, that customers satisfy themselves as to the suitability of product and material for each of their individual applications. Any reliance on information is therefore at the user‘s own risk. In no event will Trelleborg Sealing Solutions be liable for any loss, damage, claim or expense directly or indirectly arising or resulting from the use of any information provided in this brochure. While every effort is made to ensure the accuracy of information contained herewith, Trelleborg Sealing Solutions cannot warrant the accuracy or completeness of information.To obtain the best recommendation for a speci?c application, please contact your local Trelleborg Sealing Solutions marketing company.This edition supersedes all previous brochures. This brochure or any part of it may not be reproduced without permission.® All trademarks are the property of Trelleborg Group.The turquoise color is a registered trademark of Trelleborg Group.© 2011, Trelleborg Group. All rights reserved.ISO 9001:2008 ISO/TS 16949:20093QHXPDWLF?6HDOV
Most popular related searches