Potable Water Pipeline Renewal WaterLine

HydraTech Engineered Products LLC • 10448 Chester Rd • Cincinnati, OH 45215 • 513-827-9169 1 HydraTech 8001 WATERLINE EPOXY FAST FACTS PHYSICAL PROPERTIES • A High Build, solvent free epoxy lining system. • Approved for potable water contact in the United States (ANSI/NSF 61). • Low temperature cure down to 37ºF (3ºC). • Fast recommissioning time at minimum cure temperature of 37ºF (3ºC). • Fully trained application specialists. • Compatible with a variety of substrates. • Full contract support services, when required. A HIGH BUILD, SOLVENT-FREE, EPOXY LINING SYSTEM FOR POTABLE WATER APPLICATIONS. The HydraTech Waterline product is a fast-curing, solvent-free epoxy coating. To date, potable water contact approval has been granted by: • NSF International (ANSI/NSF 61) United States for pipe = 4 inches in diameter and tanks = 5 gallons Color Base - Black Hardener - White Mixed - Gray Mix Ratio (by volume) 2:1 V/V Base:Hardener Working Life – 68ºf (20ºC) 20 Minutes Drying Times – 40ºF (3ºC) Touch - 3 Hours Hard - 6 Hours Useable - 16 Hours Wet Film Thickness (mils) 40 (1000µ) Dry Film Thickness (mils) 40 (1000µ) % Volume Solids 100 Theoretical Coverage 1 Rate (m/l) Flash Point Above 212ºF (100ºC) Storage Life Twelve months when stored in original sealed containers, between 50-77ºF (10-25ºC) Tensile Strength (MPa) 22.26 Elongation at Yield (%) 1.18 Young’s Modulus (MPa) 1814 Compressive Yield Strength (MPa) 118.67 Flexural Strength (MPa) 38.21 Coating to Concrete 3316 Bond Strength (N) Coating to Metal 2808 Bond Strength (N) PRODUCT INFORMATION INCORPORATING TECHNICAL AND HEALTH & SAFETY DATA APPLICATION RECOMMENDATIONS SUGGESTED USE: A low temperature cured lining system for equipment, vessels and pipes which require approval for contact with drinking water for human consumption. SURFACE PREPARATION: Surfaces must be sound and free from grease, dust and, if possible, all moisture. Minimum Application Temperature 40ºF (3ºC) Maximum Relative Humidity 85% Substrate Temperature 5ºF (3ºC) above dew point Thinning Not Recommended Brush/Roller Application Multi-coats are necessary to achieve correct film thickness. To aid application at low temperatures, both components should be warmed to 60-68ºF (15-20ºC) prior to mixing. Mix and apply as quickly as possible. Airless Spray Application See attached Airless Spray Details page. Cleaning Fluid Universal Equipment Cleaner HydraTech Engineered Products LLC • 10448 Chester Rd • Cincinnati, OH 45215 • 513-827-9169 2 PHYSICAL DATA FIRST AID PROCEDURE INHALATION: Effect – Headache, dizziness. Emergency First Aid – Remove into fresh air; loosen collar; do not walk around. SWALLOWING: Effect – Irritation. Emergency First Aid – Do not induce vomiting; seek medical advice. EYES: Effect – Irritation. Emergency First Aid – Flush with clean water for ten minutes; seek medical advice. SKIN: Effect – Irritation. Emergency First Aid – Remove contaminated clothing, wash thoroughly with soap and water. SPILLAGE APPEARANCE: Base – Black Thixotropic Liquid Reactor – White Liquid ODOR: Base – Very Mild Reactor – Strong Amine Odor COMPOSITION: Base – Epoxy Resin, Iron Oxide, Thixatrope Reactor – Aliphatic Amine, Silica, Titanium Dioxide % VOLATILES: Base – 0% Reactor – 0% FLASH POINT (Abel Closed Cup): Base – 212ºF (100ºC) Reactor -212ºF (100ºC) O.E.L. (8 Hours): Base – Unknown Reactor – Unknown LD50 (Indications Only): Base – Unknown Reactor - Unknown PERSONAL PROTECTION CLEAN-UP METHOD: Scrape up excess material or absorb onto sand or sawdust and place in sealable containers. Ventilate area, avoid inhalation of vapors. WATE DISPOSAL: See MSDS. FIRE INHALATION: Wear suitable respiratory cartridge mask in enclosed spaces. Work in well ventilated areas. EYES: Wear suitable goggles. SKIN: Wear protective clothing and gloves made of impervious material. STORAGE: Store away from direct sunlight and sources of heat. Do not allow temperature to exceed 77ºF (25ºC). EXTINGUISHING METHODS: Fire Carbon Dioxide, Dry Powder, Water Mist. SPECIAL PROCEDURES: Do not inhale vapors. UNUSUAL HAZARDS: Dangerous to aquatic life. Do not let uncured material enter the water course. AIRLESS SPRAY DETAILS EQUIPMENT: Dual component feed hot airless spray SPRAY TEMPERATURE: 95-115ºF (35-45ºC) SPRAY PRESSURE: Minimum 2200 psi at the tip NOZZLE SIZE: 19-21 thou tip 60º nozzle angle WORKING TIME: Maximum 5 minutes (@104ºF [40ºC]) HydraTech 8001 WATERLINE EPOXY FAST FACTS