Prime Flex 900 XLV Brochure

PrimeFlexPrimeRezPrimeGelPrimeCoatPrimeBondJointShieldPrimeGuardPrimePatchWater Activated Polyurethane Foam Injection ResinADVANTAGES:• Single component.• Extremely tough and fl exible.• Up to 600% expansion unconfi ned.• Super low viscosity will penetrate tight cracks.CONFORMS TO:ANSI / NSF Standard 61 for contact with Drinking WaterPACKAGING:• 1 Gallon Jugs (case of 4)• 5 Gallon Pail• 2:1 “Quick Mix” Cartridge (case of 10) • 10 oz “Single Shot” Cartridge (case of 20) Packaged under a dry nitrogen blanket.DESCRIPTION AND USES:Detailed DescriptionPrime Flex 900 XLV is a thin liquid resin that reacts with water and expands to form a closed cell, watertight foam. 900 XLV is used to seal actively leaking joints and cracks in concrete structures. Material is typically injected under pressure through injection ports.Technical DescriptionSingle component, water activated, hydrophilic, low viscosity, polyurethane injection resin.UsesSealing active leaks in above or below grade concrete struc-tures. Hairline Cracks, Expansion Joints, Wide Cracks, Pipe Joints, Pipe PenetrationsOil Free Oakum or Open Cell Backer Rod may be soaked in Prime Flex 900 XLV to create a watertight gasket.Typical StructuresWater Treatment Tanks, Dams, Below Grade Concrete Walls, Tunnels, Manholes, Elevator Service Pits.PHYSICAL PROPERTIES:Physical Properties 73º F- LiquidViscosity 250-350 Centipoise. Solids Content 88%.Physical Properties - CuredTensile Strength (ASTM D-3574) 450 p.s.i.Tensile Elongation (ASTM D-3574) 350%Shrinkage (ASTM D-1042 / D-756) Less than 2%Tear Resistance (ASTM D-3574) 21 lbs / inch These properties were based on foam cured under pressure to simulate con-ditions inside a confi ned crack. Properties will vary depending on application conditions.Reaction TimesInitial Reaction 30 secondsFull Rise 1 minute, 50 secondsFull Cure 24 hours© 2012 Prime Resins, Inc. All rights reserved.GENERAL GUIDELINES:Store material overnight to precondition to 70º-80º F prior to use. It is not neces-sary to pre-mix Prime-Flex 900 XLV prior to use.Uses available water to initiate reaction. Inject as a single component or twin stream 2 parts resin to 1 or 2 parts water.See www.primeresins.com/primepractices.phpEco Flush, Oakum, Injection Ports, Prime Plug, Injection PumpsSafety Glasses, gloves, avoid skin contact, do not ingest, for professional use only, see MSDS. For use in well ventilated areas only to keep vapor concentra-tions low. Use mechanical ventilation if necessary. Use self contained breath-ing apparatus in confi ned areas.Flush injection equipment with Prime Flex Eco Flush.Clean off of skin with soap and water.Remove cured material by soaking in Prime Flex CGC.Cured material is environmentally safe. Dispose of in approved landfi ll. Clean up any spilled liquid material and add a small amount of water to cure unre-acted material.Eye Contact: Immediately fl ush with large amounts of water. Seek medical at-tention. Inhalation: Move to fresh air if symptoms occur. If breathing is diffi cult, seek medical attention. Ingestion: Seek medical attention immediately. Skin Contact: Wipe off contaminated area and wash with soap and water.Cold temperatures will slow down reaction time and increase viscosity. pH below 3 or above 10 may adversely affect foam properties.Prime Resins warrants its products to be free from manufacturing defects and that products meet the published characteristics when tested in accordance with ASTM and Prime Resins standards. No other warranties by Prime Resins are expressed or implied, including no warranty of merchantability or fi tness for a particular purpose. Prime Resins will not be liable for damages of any sort resulting from any claimed breach of warranty. Prime Resins’ liability under this warranty is limited to replacement of material or refund of sales price of the material. There are no warranties on any product that has exceeded the “shelf life” or “expiration date” printed on the package label.Store in dry environment between 40º and 80º F. Shelf Life: 18 months from date of manufacture in unopened containers prop-erly stored.Shipping Class: Motor Freight Class 60Hazard Classifi cation: Non HazardousThis product is manufactured by Prime Resins under strict quality assurance practices at our Conyers, GA plant.Material PreparationMix Ratio and Mixing Procedures:How To Use:Accessory Products:Personal Protection:Cleanup:Environmental Protection:First Aid:Limitations:Warranty:Storage:Shipping Information:Manufacturer Information:Rev. 03/11