RA 2, RA 6, RA 8, RA 12 (AVM/MVM) Brochure

RA and RA HPipe Cutting and Beveling MachinesRA 2, RA 6, RA 8 and RA 12Perform economical cutting and beveling with technology made by Orbitalum ToolsAdvantages:• Multiple point clamping• Fast adjustment of dimensions• Regulated cutting speed• Optimal tool contact• Working direction from the inside towards the outside• Fast tool replacementYour benefits:• Square, burr-free and deformation-free pipe end• Cold machining process• Cutting in seconds• Simultaneous or seperate cutting and beveling• Increased productivity• Improved cutting quality• Increased service life of toolsprecision.power.simplicity.l Planetary Cutting Technologywww.orbitalum.coml also available with automatic or manual feed module AVM/MVM Info-Hotline: +49 (0) 77 31 792-787 up to 789© Orbitalum Tools GmbH | An ITW Company | 11.2008Josef-Schüttler-Straße 17, 78224 Singen, GermanyPhone +49 (0) 77 31 792-0, Fax +49 (0) 77 31 792-524www.orbitalum.com, tools@orbitalum.comPipe Cutting and Beveling MachinesTechnical data RA 2 (H) RA 6 (H) RA 8 (H) RA 12 (H)Weight [kg]* 45 (47) 95 (97) 115 (117) 135 (137)Power [kW] 1.6 1.6 1.6 1.6Protection class Totally insulated in accordance with class II, DIN VDE 0740Built-in electronic speed regulation with speed stabilisation [rpm]*150 - 270(40 - 70)150 - 270(40 - 70)150 - 270(40 - 70)150 - 270(40 - 70)Versions 200 - 240 V, 50/60 Hz or 100 - 120 V, 50/60 Hz. Pneumatic drive only on request.Vibration level according to EN 28662, part 1 [m/s²] 2.5 2.5 2.5 2.5Noise level in the workplace approx. [dB (A)] 75 75 75 75 Working range RA 2 (H) RA 6 (H) RA 8 (H) RA 12 (H)Pipe OD [mm]Pipe OD [inch]12 - 630.472 - 2.48044** - 1821.732** - 7.165114 - 2304.488 - 9.055154 - 3256.063 - 12.795Wall thickness, depends on material [mm]***Wall thickness, depends on material [inch]***1.5 - 5.50.059 - 0.2172 - 100.079 - 0.3942 - 100.079 - 0.3942 - 100.079 - 0.394Pipe ID min. (saw blade-Ø 63 mm) [mm] Pipe ID min. (saw blade-Ø 2.480 inch) [inch] 70.276762.9921375.3941857.283Pipe ID min. (saw blade-Ø 68 mm) [mm]Pipe ID min. (saw blade-Ø 2.677 inch) [inch] 20.079712.7951325.1971766.929Pipe ID min. (saw blade-Ø 80 mm) [mm]Pipe ID min. (saw blade-Ø 3.150 inch) [inch]- 592.3291204.7241646.475Pipe ID min. (saw blade-Ø 100 mm) [mm]Pipe ID min. (saw blade-Ø 3.937 inch) [inch]- 391.5351013.976 1445.669* Values in brackets for RA H (= with intermediate gear)** Special clamping jaws must be installed for pipes with an outer diameter (OD) of < 85 mm (3.346 inch). These are already delivered with the RA 6 (H).*** Depending on the wall thickness special clamping shells for thin-walled tubes are required (accessory)The technical data are not binding. They are not warranted characteristics and are subject to change. Please consult our general conditions of supply.A wide range of saw blades and bevel cutter are especially designed for our pipe cutters for highest requirements and longest service life.High-performance lubricants for pipe cutting and beveling to increase the saw blade life-time.Synthetic saw blade lubricating compound GF TOP, Tube, 180 g: Code 790 060 228.Saw blade lubricating compound ROCOL, Tube, 150 ml: Code 790 041 016.Special stainless steel clamping jaws for RA 2, RA 21 S: Code 790 041 323.For RA 4: Code 790 042 201.Aluminum clamping jaws for RA 4 and RA 41 Plus: Code 790 046 250.Customised aluminum clamping shells for RA 6, RA 8, RA 12, GF 4, GF 20, RA 41 Plus: for deformation-free clamping of thin-walled tubes.Very sturdy and stable pipe feeder: feeds accurately long and heavy pipes into RA machines.Base unit: Code 790 068 051Extension unit: Code 790 068 061Code 790 700 202_03Stamp of distributor: