RCB 6000 Wireless Industrial Data Transmission Brochure

RCB 6000 This information is for guidance only and JMei reserves the right to change it without prior notice. JMei SPRL Chaussée de Rochefort, 123 – B- 6900 MARLOIE- Tél. : +32 84 34 41 75 – Fax : +32 84 34 41 77 info@jmei.be – www.jmei.be – TVA : BE 0534 889 177 Wireless industrial data transmission RCB 6000 System description JMEI multichannel wireless transmission systems RCB6000 are designed for a reliable transmission of all types of digital or analogue signal over distances of up to 5000 m in industrial environment, thus enabling a significant reduction in all types of control and measurement cables between units and the PLC/automatic controller and between units themselves. RCB6000 transmission systems can be used to exchange all types of signal, whether RS232 or 485 or others. Moreover, JMEI Wireless radio transmission RCB6000 system are designed with a data processor board, which one includes two micro controllers, both control in real time all messages between transmitter and emitter thus providing à superior security class. In case of system failure, RCB 6000 system proceeds at once to emergency stop. Principle The basic RCB6000 transmission system includes a transmitter unit and a receiver unit. These units can be used to send or receive all types of digital signal, and also analogue signal, using radio frequencies. The radio units can communicate in unidirectional or bidirectional mode using a single frequency (technology based on a transceiver). The transmission systems use a technology based on our extensive experience in this field (+/- 15 years), i.e.tried and tested in industrial applications such as steel works and foundries and in an environment where the electromagnetic interference may be very strong. They operate either in the frequency band 434 MHz or 868/870 MHz (license-free frequency) using a low power output (less than 10mW) as standard, in order not to interfere with other radio controlled applications on the client’s site. Specifications Isolated power supply 24/48, AC or DC isolated 20 (or 40) digital inputs 8 analogues outputs (U or I) 8 analogues inputs opto-coupled (U ou I) Link to application RS232 or RS 485 20 (or 40) digital outputs Unidirectional or bi-directional transmission Multichannel 64 channels available Link to application RS232 or RS 485, or Profibus or Ethernet RCB 6000 This information is for guidance only and JMei reserves the right to change it without prior notice. JMei SPRL Chaussée de Rochefort, 123 – B- 6900 MARLOIE- Tél. : +32 84 34 41 75 – Fax : +32 84 34 41 77 info@jmei.be – www.jmei.be – TVA : BE 0534 889 177 Transmission reliability and safety in use The JMEI /RCB7000 units have control systems and codes designed to ensure a high level of reliability against interference or interruptions, which could be caused by other radio frequency sources on the site, by means of the following: Address codes identifying the JMEI receiver and transmitter (32-bit codes) Frame coding sent by 16-bit CRC /JMEI code. Continuous re-reading by internal protocol and message verification. In the event of interference, the transmission channel can easily be re-programmed by PC on site, 64 channels are available. In bi-directional mode, there is also the option to check if the digital contact signals have been processed properly. Upgrade security: all messages are controlled in real time by two micro controllers, providing à superior security class in case of system failure. In case of system failure, equipment will set automatically in stand by procedure, waiting restarting command. System composition 2 transmitter or receiver units, housing either in polycarbonate (or aluminium, as an option) IP65 waterproof housing can be installed outside or inside buildings may also be installed in an electrical cabinet. 24 or 48 V AC/DC power supply (powered by batteries also possible). Unit supplied with fixing screws and rubber bushing. Omni-directional antenna fixed inside the housing, no particular installation requirements, i.e. not sensitive to the presence of a metal mass in the propagation field. Option to connect several transmitters and receivers together to create a network. Option: Receiver type RCB 7000, can be inter connected with Profibus, Ethernet, CAN bus or any other fieldbus connection to the PLC customer application. Applications Remote wireless transmission of all types of analogue measurement signal, for example weight, pressure, temperature, speed, etc. to a central PC or automatic controller. Transmission of all digital or analogue signals, for example position of mobile machinery, zoning of overhead cranes or other mobile plant, remote control of machinery, pumps, motors etc., transmission of information between a mobile machine (clark/or equivalent industrial forklift) and a fixed unit., foreseen with possibility of emergency stop class 3 transmission Transmission of information of all types from display screens. Control and access authorisation management, remote barrier opening and closing, transmission of access badge information, access control. References for the RCB6000 type Equipment of this type has recently been installed to: ArcelorMittal, Riva Steel Plant, Manoir industrie iron casting, Burgo Ardenne paper industry, Car industry Group Peugeot/PSA, Glaverbel, Arcelor Sidmar Gent, Airbus industrie, Caterpillar, SNCF. Mechanical and electrical properties: -Transmitter/Receiver: Unit dimensions:220x270x90 mm(excluding aerial and rubber bushings) Protection rating : IP65 Weight : 1,5Kg Operating temperature: - 20 °C à + 55 °C 24 to 48V AC/DC power supply or 12V DC (option) Digital inputs: opto-coupled (from 12 to 24V AC or DC) (on potential-free inputs or via isolated power supply) Digital outputs: 8A (resistive) 250V AC max E/S analogue: 0-10V, -10/0/+10V, 0-5V, 0-20mA, 4-20mA,.. The RCB6000 system can also convert magnitudes (e.g.: 0-10V to 4-20mA, 0-5V to RS232, etc.) Radio unit: UHF (433.125 à 434.750 MHz)– 64 channel frequency synthesiser programmable by PC Output: < 10 mW (range from 100 to 5000 m depending on the environment) Modulation : FM : FSK Transmission coding: 32-bit address and 16-bit CRC