TYPE: Water-based acrylic
FINISH: Matte
Color: Milky white (wet) Translucent (dry)
Mixable with other products: no
Paintable: yes
Sizes: 1, 5-US gallon containers
Disposal: in accordance with local, state & federal regulations
Application Equipment: airless spray, brush, roller
Mixing: ready to use, mix thoroughly
Drying Time: 2 to 6 hours to touch depending on ambient temperature
Full Cure: 11-15 days depending on ambient temperature
VOC: <195 g/l
Clean up: soapy water

PROHIBITED: ?oors, stair treads, thresholds, as well as the sashes, parting bead‘s, window wells, and the interior/exterior or header stops of movable windows.

SURFACE PREPARATION: All surfaces must be clean, sound, dry & free of dust, rust, grease, oil, mildew & loose particles before application. A licensed deleader must remove all ?aking and peeling paint down to a sound surface. Repair damage with a joint compound and smooth over with a damp sponge to remove excess compound and blend into surrounding wall surface. Remove all oil, grease, wax, smoke residues and other contaminants by washing with a suitable cleaner and rinsing with clean water. Remove mildew by washing with a solution of TSP (tri-sodium phosphate) in 1 gallon of water and add 1 quart of commercial bleach. Wear gloves and protective eyewear if using bleach solutions. For high-gloss surfaces, wet scour with TSP or a strong detergent substitute and water solution using course steel wool to eliminate any gloss. Thoroughly remove by washing any residual scouring material, detergent or other surface preparation material, and dry completely prior to application. Although no special primers are required, there may be occasions where primer would be bene?cial in the overall performance of the coating. Prime water stains with stain blocking primer, prime chalking with penetrating chalk primer, prime bare wood within a enamel undercoater; prime drywall with a quality acrylic primer & sealer.

ENCAPSULANT APPLICATION: Apply in the multiple coats to achieve total thickness of 20 mils (wet). Use a wet mil gauge when applying product. Do not apply if ambient temperature is below 45°F. Airless spray application in two costs (each 10-12 mills) is recommended for best results, including a smoother dry ?lm. Use .017 to .019 inch ori?ce & a 60 mesh screen. If applied with a brush or roller, multiple coats are required to achieve the required thickness. Expect 10-12 mils per coat by brush and 10-12 mils per coat by roller. Use a polyester or polyester/nylon brush. Use a high-quality tapered trim brush with the ?lament density to achieve a smooth ?nish on all trim work. Application to a large smooth or any size rough area should be performed with a quality roller cover with a half inch cover to three-quarter inch nap. Regular paint topcoats may be applied over services that have been sprayed, rolled or brushed with LeadClear if desired.

OCCUPANCY DURING APPLICATION: occupancy is permitted during brush or roller application, but not in room or interior area being encapsulated. For spray application, occupancy is prohibited during the day for work site safety reasons only. Occupants may return at the end of the workday.

OCCUPANCY AFTER APPLICATION: Yes. Use adequate ventilation for ?rst 24 hours after application.

CAUTIONS: did you use adequate ventilation. If respiratory irritation develops, increase ventilation or where respiratory protection. Use molded polymesh shell dust and mist respirator – MSHA, NIOSH, Approval No. TC-21C-287 or equivalent during spray application. Avoid contact with eyes and skin. Wash hands thoroughly with soap and water after using. During application wear gloves and safety goggles.

WARRANTY: LeaClear has limited product liability for 20 years. The purchaser shall notify Tara JV Corp. within 30 days after purchase to advise of any assumed manufacturing defects.

CARE AND MAINTENANCE: LeadClear will not protect occupants from ingestion of the encapsulated lead based paint if surface is damaged, broken, or abraded. Surfaces coated with the LeadClear must be inspected routinely for holes, cracks, dents, peeling services, bubbles, or any other defects; including water damage. Damaged surfaces should be repaired and re-encapsulated immediately to prevent exposure to the lead hazard.

REFERENCES:

Deciding whether to encapsulate by Childhood Lead Poisoning Prevention Program.
Register of approved encapsulants by Childhood Lead Poisoning Prevention Program.
Care and maintenance of encapsulants by Childhood Lead Poisoning Prevention Program.
Material safety data sheet (MSDS) by Childhood Lead Poisoning Prevention Program.
LeadClear from Container by Tara JV Corp.

Massachusetts General law (MGL) c. 111, 189A–199B (the Lead Law)
Regulations for Lead Poisoning Prevention and Control 105 CMR 460.000

FOR MORE INFORMATION OR PROBLEM RESOLUTION, CALL:
Tara JV Corp. at 347-538-4591
Childhood lead poisoning prevention program at 1-800-532-9571 or 781-774-6711 (out of state)

The licensed Deleader, who applied the encapsulant. If homeowner or agent applied product, you may wish to call a licensed Deleader for advice or assistance.

Technical Data

Wet Appearance: Milkier Translucent Liquid

Dry Appearance: Translucent

Weight: 8.25-8.75lbs/gal

Speci?c gravity: 0.99 to 1.050

VOC: Less than 195 GMS/lt.

Dry Time @75 f: 2 – 6 hrs.(Depend upon substrate and weather condition)

Clean up: Water

Solid By Wt.{28fbbca4d5e380ff11c49cfcf258524327390f8bd5020b9c03575f0942ab537b}: 30 – 40 {28fbbca4d5e380ff11c49cfcf258524327390f8bd5020b9c03575f0942ab537b}

Solid By Vol.{28fbbca4d5e380ff11c49cfcf258524327390f8bd5020b9c03575f0942ab537b}: 28 – 38 {28fbbca4d5e380ff11c49cfcf258524327390f8bd5020b9c03575f0942ab537b}

Viscosity: 65 kU Minimum.

Recommended Coat: 2 Coats.

Flash Point: Non Combustible

Shelf life: 2 years

PRODUCT TESTING

ASTM E-1795
ASTM E84

Meets requirements to be utilized as a permanent method for abatement of lead-based paint.

GALLON KIT SIZES
1 & 5

Results of ASTM E1795-12 Testing - Brochure