Sensaphone - Model 2800 - Wireless Sensor Monitoring System Brochure

2800SENSAPHONE®REMOTE MONITORING SOLUTIONSRemote Monitoring with Wireless SensorsNew Wireless SensorsThe Next Generation in Sensaphone MonitoringSensaphone Introduces Wireless SensorsNow you can monitor critical conditions at remote locations without running wires. Intro-ducing the new Sensaphone 2800 with Wire-less Sensor Technology. Based on proven Sensaphone remote monitoring methods, the 2800 adds the ability to read sensor status from wireless sensors. And not just simple on/off status, or open/closed conditions. The Sensaphone Wireless Technology includes full analog capability so real world values can be monitored, like actual temperatures, real tank levels and ?ow rates.You can use up to four of the Sensaphone wireless sensors with the 2800. A variety of wireless sensors types are available to choose from, including ...TemperatureHumidityPower FailureMotion DetectorWater on FloorIn addition to the wireless sensors, there are also two Wireless Interface modules. These allow you to connect to existing equipment or sensors and transmit their status back to the 2800 wirelessly. There is a Dry Contact wireless module, and even a 4-20mA wireless module. The 4-20mA wireless module even provides battery backed 24 VDC loop power for your transducer.Sensaphone Wireless Technology includes full analog capability so real world values can be monitoredStart getting rid of your wiresPlace It AnywhereMost of the Sensaphone Wireless Sensors run on batteries for up to 3 years. You can literally, just place a sensor on the wall and start monitoring right away. The 2800 will scan, ?nd the sensor, self con?gure and do most of the work for you. All you need to do is to record a custom voice message and ?ll in a few parameters.Self DiagnosticsThe Wireless Sensor Network is always being watched by the 2800. In addition to looking for alarms from the sensor values, it is also looking to make sure that each wireless sen-sor is fully functional and its batteries are full. If there are any problems with the wireless sensors, the 2800 will initi-ate a diagnostic alarm and notify the appropriate personnel immediately.Where You Need ItAlso included on the 2800 are four traditional, hard-wired sensor inputs. These are Sensaphone Universal Inputs that can be used with temperature sensors, dry contact sensors, and even 4-20mA transducers. So, when you have monitoring requirements near the 2800, just wire them in. When wiring is inconvenient or further away, just place the wireless sensors where you need them. The wireless sensors will operate up to 300 feet line-of-sight* away from the 2800. Not far enough? Just add a wireless repeater to go farther. The repeater can be located up to 4,000 feet line-of-sight* from the 2800. Then, one or more sensors can be located up to 300 feet line-of-sight* from the repeater. Noti?cationJust like the other Sensaphone products, the 2800 uses the reliability of a standard phone line to make phone calls to the appropriate personnel to announce alarm conditions. Each monitoring condition, both wired and wireless, can have a custom voice message attached to it. Each message is recorded in your own voice for easy alarm identi?cation. Alarm noti?cation will repeat out to eight people until acknowledged.ApplicationsUse the 2800 to monitor multiple greenhouses with-out wires, multiple barns, coolers, freezers, or a wide variety of remote equipment. The new Sensaphone 2800 can be used anywhere you would use our other Sensaphone products. The 2800 just makes installation and expansion faster and easier. Extend your reach and monitor your critical remote locations with the new Sensaphone 2800. Up to four hard wired universal inputs for local monitoring.• Temperature• Dry Contact• 4-20mAWireless sensors can be up to 300 feet line-of-sight* from the 2800The repeater can be up to 4,000 feet line-of-sight* from the 2800 Direct WirelessSensorsWirelessSensors on RepeaterRepeaterFor longer distance wireless monitoring,just add a repeater between the sensors and the 2800300 feet300 feet*Wireless Distance Note: The “line-of-sight” wireless distance is the maximum distance that the wireless devices can communicate with each other in a best-case scenario. A “line-of-sight” path would be when there are no obstructions at all between the two devices. When the wireless path must go around metal objects and/or reinforced concrete walls, the reliable wireless distance will be reduced. When the 2800 is communicating directly with the sensors, the line-of-sight distance is 300 feet, and a typical indoor distance with obstructions is approx. 100 feet. When the 2800 is communicating with a repeater, the line-of-sight distance is 4,000 feet, and the typi-cal indoor distance with obstructions is approx. 300 feet. Experimentation may be required to determine actual wireless range.Available Wireless SensorsWireless Temperature SensorCan be wall mounted with screws or double-sided foam tape. Measures temperature from 32°F to 115°F (0°C to 57°C). Adding FGD-0101 temp sensor extends range down to -109°F (-85°C) Includes AAA batteries that will run for approx. 3 years. Optional AC adapter so batteries are only used during power failure..................................WSR-0100Wireless Dry Contact SensorCan be wall mounted with screws or double-sided foam tape. For Normally Open or Normally Closed contacts. Includes 3 AAA batteries that will run for approx. 3 years. Optional AC adapter so that batteries are only used during power failure....................................................................WSR-0101Wireless Power Failure SensorCan be wall mounted with screws or double-sided foam tape. Comes with AC adapter for sensing power failure. Monitors power failure from wherever the AC adapter is plugged into. Includes 3 AAA batteries to operate during a power failure....................................................................WSR-0102Wireless Humidity SensorCan be wall mounted with screws or double-sided foam tape. Measures humidity from 0 to 100% RH. Includes 3 AAA batteries that will run for approx. 3 years. Optional AC adapter so that batteries are only used during power failure..........................WSR-0103Wireless 4-20mA SensorCan be wall mounted with screws or double-sided foam tape. Works with any 4-20mA transducer. Custom table range so monitoring is in real engineering units. Built-in 24 volt power supply for providing 4-20mA loop power. Includes AC adapter. Also includes 3 AAA batteries for full operation during a power failure...............................WSR-0104Wireless Motion DetectorCan be wall mounted with screws or double-sided foam tape. Detects movement in a speci?c area for unauthorized entry or intrusion. Includes 3 AA batteries that will run for approx. 3 years...............................................................WSR-0105Wireless Spot Water Detection SensorMust be placed directly on ?oor. Detects the presence of water on the ?oor. Includes 3 AA batteries that will run for approx. 3 years..................................................................................WSR-0106Wireless Zone Water Detection SensorDetects the presence of water on a ?oor or in a false ceiling. Comes with 10 feet of water rope to cover a larger area than WSR-0106. Includes 3 AA batteries that will run for approx. 3 years. Optional AC adapter so that batteries are only used during power failure ................................................................................WSR-0107Wireless RepeaterCan be wall mounted with screws or double-sided foam tape. Extends wireless sensor range up to 4,000 feet line-of-sight.* Includes AC adapter. Also includes 3 AAA batteries for full operation during a power failure. ................................................................WSR-0199LIT-1006 © SENSAPHONE 2007 SENSAPHONE®901 Tryens RoadAston, PA 19014PH: 610-558-2700F: 610-558-0222www.sensaphone.comDistributed By: Please see our catalog or visit sensaphone.com for a complete list and speci?cations of hard wired sensors. Speci?cations subject to change without notice.