TAM-J - Multiple Set Inflatable Packer System Brochure

TAM-JMulTiple SeTinflATAble pAcker SySTeM• Highest reliability multiple-set inflatable packer system available • Element sizes for 2-3/8” tubing through 30” casing• Easy conversion to straddle toolISO 9001: 2008 Certified CompanyOptional Element Reinforcement StylesGeneral DescriptionsWith over twenty-five years experi-ence, the TAM-J tool line has a prov-en track record of performing a wide variety of functions where multiple inflate cycles are required. Different setting mechanisms are available for use with TAM-J tool systems, which allow multiple cycles without circulating additional setting balls.TAM-JThe TAM-J control tube moves the inflation port between inflate, locked-set and release positions with only right-hand torque and up/down motion. In addition to the simplicity of the “J” track, an equalization flow path from above to below the inflat-able element is opened and closed with the same up/down movement.Straight-JThe Straight-J simplifies operations further by eliminating all rotation from required tool functions, requiring only up-and-down motion.JUMBO-JA premium connection, 7” OD tool body, JUMBO-J is available to accept 7” through 141/2” OD elements. This tool configuration provides the highest tensile and torque capacity of any inflatable service tool on the market.StraddleThe TAM-J system is particularly suitable for conversion to a straddle packer assembly to selectively isolate zones for testing or treating. The straddle interval is adjustable from 3-ft. (1 m) to as long as desired by adding tubing between packers.In one well in Canada, the TAM-J Straddle was used to selectively acidize fifty-seven intervals in a horizontal well, on a single trip into the well.Inflation ElementsTAM offers four types of inflatable elements to satisfy the wide range of application requirements in vertical, horizontal, cased or open hole. These include the IE (weave type), SE (slat type), VE (dual layer canted slat type) and HE (hybrid slat and weave type) elements. They come in various sizes and are designed to operate in holes ranging in diameter from 23/8” through 30”.TAM-J Key FeaturesA typical TAM-J Straddle assembly can be made-up and ready to run in an hour or less.Special packer mandrels and extensions are available for high-pressure operations, and special packer elements are available for high-temperature service.Weave Type Element (IE)• Multiple-set applications• Sets in perforations, slots, fractures, or open hole• Seldom leaves rubber in the holeWeave Type Element (HE)• Combination of Slat element for extrusion resistance, and Weave element for multi-set capabilitiesSlat Type Element (TE & SE)• Single and multi-set applications• Exposed slats function as slipsCanted Slat Dual Layer (VE)• Single and multi-set applications• Cased or open hole• Benefit of Slat type for HPHT• Sets in perforations, slots, fractures, or open holeHow the Packer Works (ball choke)The packer is run on the work string, drillpipe or tubing with the “J” track control in the inflating position.Drop a steel ball to seat at the choke. Pressure up to inflate the packer. See back page for alternate setting mechanisms.Pick up and rotate a quarter turn to the right, then slack off weight. With the inflating and equalization port between PolyPak seals, packer element is isolated from pressure inside the work string.Pressure up to shear the ball and choke, opening the mandrel through the packer.Set down with about 2,000 lbs. at the tool. Rotate a quarter turn to the right and pick up to deflate the packer. Fluid drains into both the work string and into the annulus outside the packer, allowing the packer to deflate fully.To reset the packer in the hole, pump a phenolic ball down to the remaining ball seat, and repeat the setting procedure. The phenolic ball will shear through the seat, again opening the mandrel through the packer.Running in Inflating SettingReady to WorkReleasing ResettingTAM-J Applications–VerticalProblem:• Scale build-up in perforationsSolution:• Run Thru-Tubing• Straddle and acidize individual perforation setsProblem:• Screen & gravel pack plugged Solution:• Perform multiple sets to selectively acidize screenTAM-J Applications–VerticalProblem:• Leak in 22-inch casing or shoeSolution:• Perform multiple tests to determine exact depth of leak and squeeze cement to repairProblem:• Well requires P&A • Corroded tubing Solution:• Perform multiple sets to locate leaks• Squeeze perforations and spot annulus cement plugsTAM-J Applications–HorizontalProblem:• Well producing excess waterSolution:• Perform multiple production tests to determine water entry pointProblem:• Multi-lateral well producing excess waterSolution:• Selectively test each legTAM-J Applications–HorizontalProblem:• Severe lost circulation in lateralSolution:• Squeeze cement L/C zonesProblem:• Low productivity due to formation damageSolution:• Perform multiple matrix acid treatments as requiredOptional Setting Mechanisms800.462.7617713.462.7617713.462.1536 Faxinfo@tamintl.comWorldwide sales and service contacts at www.tamintl.comThe information and/or data in this publication is supplied solely for informational purposes and TAM International makes no guarantees or warranties, either expressed or implied, with respect to its accuracy, completeness or use.TAM International Inc. 2/11A ball and prong configuration where the prong kicks the ball off seat when down movement is applied to the work string after inflation. This setting mechanism allows circulation while running into the well and prior to dropping the ball to the seat. It provides a means for multiple sets without dropping additional balls.No balls are dropped in this setting mechanism and the tool is always in either the inflating or treating position. This mechanism is designed for multiple set operations. It is particularly reliable in horizontal applications as there is no requirement to place a ball onto a seat.The standing valve is used for special testing programs, such as hydraulic fracturing stress testing, when it is important to protect the target formation from pressure (e.g. shearing the setting ball) prior to the test. After the packers are inflated and pressure in the work string is released, the valve is lifted by wireline, opening through the mandrel.This mechanism allows multiple sets by circulating a ball to seat for each inflation cycle. It provides the largest flow capacity of any of the setting mechanisms.mm 42.9 54 66.7 77.8 87.3 108 140 178inches 111/16 21/8 25/8 31/16 37/16 41/4 51/2 7mm 13.20 14.20 23.90 35.10 35.10 50.80 63.50 76.20inches 0.52 0.56 0.94 1.38 1.38 2.00 2.50 3.00inches 1.315NU1.315EU1.900EU2.375EU2.375EU2.375EU 3.5 IF4.5IFTAM-JOutside DiameterMandrelInside DiameterTop ConnectionElement Range: 111/16” up to 141/2”Auto Choke Auto PistonStanding ValveCollet ChokeInflating Treating Inflating TreatingInflating Treating Inflating TreatingStandard TAM-J Sizes SF-19 Packer Application Analysis Input.pdf