TRIBO guard II - Model 4002 - Dust Monitor Specification Datasheet

sales@auburnsys.com • www.auburnsys.com • Phone: 800-255-5008 or 978-777-2460 • Fax: 978-777-8820 TRIBO.guard I 4002 TM May 2010 REQUEST FOR QUOTE: Name _________________________________________________________ Title __________________________________________________________ Company_______________________________________________________ Address________________________________________________________ City _____________________________State _______Zip________________ Telephone (_______)__________________Fax (______)_________________ Email __________________________________________________________ APPLICATION CONCERN ? Fabric Filter ? Environmental ? Cyclone ? Maintenance ? Other ? Process/Prod. Loss PROCESS CONDITIONS Temperature _________o F (Co ) Particulate _________________ Duct ID __________inches (cm) Gas ______________________ Pressure _________psig (bar) Velocity __________ft./min (m/s) Comments______________________________________________________ _______________________________________________________________ SPECIFICATIONS: ELECTRONICS Enclosure NEMA 4 (Integral sensor); NEMA 4/7/9 (Remote sensor) Power 105-130 VAC (210-260 VAC or 10-32 VDC optional), 50/60 Hz Power Required 5 Watts maximum load Operating Temperature 20º to 140ºF (-30º to 60ºC) Humidity Range 0 to 95% relative; non-condensing Hazardous Rating Designed for Class I & II; Div. 1 & 2; Group B, C, D, E, F & G. CE approved. Sensitivity Range Adjustable 100-1 range; 0.0005gr/dscf (1 mg/m3) typical detection Sensitivity Setpoint Baseline level setting indicated by first segment of LED bar graph Smoothing Adjustable from 0.1 to 22 seconds Output 4-20 mA non-isolated, 500 Ohm loop max; 10 seg-ment LED bar graph (0-100%) SENSOR Sensor Probe 316 stainless steel (STD); other materials available. Other Wetted Parts 303 Stainless Steel minimum grade Insertion Length 3, 6, 12, 18, 30, 36 inch (7.6, 15.2, 30.5, 45.7, 76.2, 91.4 cm) Standard Integral Sensor Assembly Quick release fitting with ferrule, clamp, gasket, and extended PFA insulator; usable in gas streams to 160ºF (70ºC). Remote Sensor Assembly Quick release or ½" NPT mounting and extended PFA insulator, usable in gas streams to 475ºF (240ºC). NEMA 4X enclosure. Options Ceramic insulator, usable in gas streams to 1,000ºF (540ºC). PREVENT DUAL ALARM SYTEM ** TRIBOTRAC LEAK LOCATOR SYTEM** **Please contact your rep or Auburn for additional information on these options. Quotation Date ______________ Number of Units __________ Unit Price $____________ Total $ __________________ Est. Delivery _______ week(s) ARO (Quote valid 30 days; FOB Danvers, MA.) Model #: 4002 - ELECTRONICS E1 Power 1. 105 to 130 VAC, 50/60 Hz 2. 210 to 260 VAC, 50/60 Hz 9. 10 to 32 VDC E2 Output 1. 4-20 mA, 0-100% bar graph 2. Add: Pre-Vent Dual Alarm System 3. Add: Tribotrac Leak Detector System SENSOR Base - System Style I. Integral Sensor R. Remote Sensor (Cable Required) S1 Probe Material 1. 316 Stainless Steel 4. Hastelloy 2. Carbide 9. Special 3. Inconel S2 Insulator Material 1. Teflon (TFE): -40o to 300o F (-40o to 150o C); up to 30 psi 2. Ceramic (High Temperature or Pressure): -40o to 1000o F (-40o to 540o C); up to 2000 psi 3. Teflon (TFE) with Air Purge: -40o to 300o F (-40o to 150o C); up to 30 psi 4. Ceramic with Air Purge 5. Extended High Performance (PFA): Standard -40o to 475o F (-40o to 240o C); up to 30 psi 6. Extended High Performance (PFA) with Air Purge 9. Special S3 Probe Insertion Length* 1. ½” (1.3cm) 5. 18” (45.7cm) 2. 3” (7.6cm) 6. 30” (76.2cm) 3. 6” (15.2cm) 7. 36” (91.4cm) 4. 12” (30.5cm) 9. Special * Probe length should reach approximately mid-duct; for large ducts (>72”). Contact Auburn for additional options. S4 Sensor Mounting F. Flanged S. Special N. 1/2” Male NPT T. Threaded Quick Release Q. Quick Release V. Venturi (Fugitive Dust) Cable Length (feet) _______@ $________/foot Cable Terminals Factory Installed _______@ $________/set or Field Kit _______@ $________/set Extras Manuals (one included) _______@ $_______each Stainless Steel Tags _______@ $_______each Set of Prints _______@ $_______each Spare Parts Kit _______@ $_______each Field Test Unit _______@ $_______each Please consult factory or your local representative for proper recommendations. To expedite a quotation, please complete the follow-ing worksheet and fax it to us at 978-777-8820 or email to sales@auburnsys.com. ___________ Electronics Base ___________ E1 Power ___________ E2 Output ___________ Sensor Base ___________ S1 Probe Material ___________ S2 Insulation ___________ S3 Length ___________ S4 Mounting ___________ Cable ___________ Connectors ___________ Extras $____________ Total ?? -?- ????