Turbidity & Suspended Solids Analyzers TR6 Series- Brochure

Applica%ons• Monitoring WWTP discharge• Filter rupture or backwash• Clarity in Se0ling Ponds• Monitoring Surface Waters• Environmental Monitoring• Control of Clear Rinse WaterFeatures• 2 Channel capability, Turbidity+pH, DO, Cond, pIon or Turbidity• Side or End mounted Op/cs• Waterproof Cable• Mul/ple Installa/on MethodsImmersion or Flow Through• NTU, FNU, mg/L, ppm, % SolidsELECTRO-CHEMICAL DEVICESModel Triton® TR6Turbidity / SuspendedSolids SensorsThe Triton®TR6 sensor is designed for the con/nuousmeasurement of turbidity or suspended solids in variousranges from 0 -250 NTU to 0 - 4000 NTU. The sensor emits abeam of 850 nm near infrared light into the sample where itis sca0ered by par/cles suspended in the water. The amountof back sca0ered light returning to the sensor is measuredand correlated to the turbidity or the amount of suspendedsolids in the sample. The TR6 response depends on the size,shape and composi/on of the suspended par/cles. For thisreason, mg/L, ppm and % Solids measurements must becalibrated with suspended solids from the waters to bemonitored. Turbidity measurements (NTU, FNU) can becalibrated with calibra/on standards such as Formazin,StablCal or SDVB beads.The Triton®TR6 is available in two op/cal configura/ons, onewith side mounted op/cs, the TR6-2 or -3 and the other withaxially front mounted op/cs, the TR6-1. These design op/onsaddress the fact that reflec/ve surfaces in the emi0ed lightsrange will yield ar/fically high readings. The side mountedop/cal configura/on minimizes interference from surfacesbelow the sensor while the axially mounted op/cs avoidinterference from surfaces around the sensor. A daylightrejec/on filter blocks sun light and reduces ambient-lightinterference. The axial front mounted op/cs of the TR6-1 aresurrounded with a copper ring that inhibits the growth ofalgae and other biological films.The Triton®TR6 sensors are dual range sensors, each having alow range output and a high range output. Either the highchannel or low channel can be displayed by simply switchingthe signal wire to the input card. The available Triton®TR6sensor ranges are;0-250 NTU with 0-1000 NTU0-500 NTU with 0-2000 NTU0-1000 NTU with 0-4000 NTU0-2000 NTU with 0-4000 NTUThe Triton®TR6 sensors are designed to work with the C22analyzer or T80 transmi0er. The T80 is a single channeltransmi0er while the C22 can be configured as a single or dualchannel turbidity/suspended solids instrument. The C22allows the turbidity/suspended solids measurement to becombined with any of the other standard measurements, pH,ORP, pIon, Conduc/vity or Dissolved Oxygen.Installa/on is accomplished with a 1” stand pipe forimmersion service or with the PVC flow cell for an in line flowthrough applica/on. Either op/cal configura/on is suitable forimmersion service while only the Side Mounted op/calconfigura/on is suitable for in line service.The standard cable is water resistant 5 conductor cable. It isavailable with 10 , 20 or 30 (9.1 meters) lengths. Anop/onal waterproof cable is available for immersion orsubmersion applica/ons. The TR6 is suitable for submersionto depths of 500 meters.Designed for use in environmental water, the Triton®TR6 issuitable for most aqueous applica/ons. It is not suitable foruse in organic solvents or in solu/ons with an extreme pHvalue, only use when the pH is between 2-12 pH. Thetemperature range for the sensor is 08 to 508C.Descrip%onTriton®TR6 Turbidity SensorRepresented by:Specifica%onsMeasuring principle:Par/cle caused back sca0ering of 850 nm near infrared lightwith sunlight rejec/on filterMeasuring Range:-1 sensor,0.0 ... 250.0 NTU, FNU & 0 ... 1000 NTU, FNU-2 sensor0.0 ... 500.0 NTU, FNU & 0 ... 2000 NTU, FNU-3 sensor0 ... 1000 NTU, FNU& 0 ... 4000 NTU, FNU-4 sensor0 ... 2000 NTU, FNU & 0 ... 4000 NTU, FNUppm, mg/L and %solids to equivalent NTU value (See figurebelow)Accuracy2% of reading or 0.5 NTU, whichever is largerProcess Temperature Range:–5 ... 50°CTemperature Compensa%on:Internal Temperature compensa/onProcess pressure range:50 psi max. in Flow Cell. Vacuum opera/on is not permi0ed,500meter submersion depth (50 bar,725 psi)Dri?:< 1% / monthWe&ed MaterialsSensor body: stainless steel AISI 316 TiSensing end: epoxyProcess Connec%on:1” NPT Nylon compression fi1ngElectrical connec%onWaterproof 5-wire measuring cable orWater Resistant 5-wire measuring cable(Standard)Cable Length:10 (3.0 m), 20 (6.1 m), 30 (9.1 m) cablesTriton®TR6 Turbidity SensorTritonTR6 C0914Model Triton®TR6 Turbidity Sensor, Part # GuideTR6 Sensor Style (op%cal configura%on)1 Front Mounted with copper ring for use with immersion assembly2 Side Mounted, for use with immersion assembly3 Side Mounted for use with flow through cellProcess Connec%on0 None1 1” MNPT Nylon Gland Fi1ng2 Flow Through Cell, 2 x 2” FNPT entries, 1 x 1” FNPT sensor portCable Length Water Proof Cable #’s (01-03) Standard Cable #’s 04-06(01) 04 10 (3.0 m)(02) 05 20 (6.1 m)(03) 06 30 (9.1 m)Measurement Ranges0 0-250 NTU and 0-1000 NTU1 0-500 NTU and 0-2000 NTU2 0-1000 NTU and 0-4000 NTU3 0-2000 NTU and 0-4000 NTUTR6- 1 0 01 2Electro-Chemical Devices1681 Ke0eringIrvine, California, USA 92614Phone: +1-949-336-6060+1-800-729-1333Fax: +1-949-336-6064email: sales@ecdi.comweb: www.ecdi.comSpecifica?ons subject to change without no?ce.Model Triton® TR6 Installa/on AssembliesPart # Descrip%on1000260-5 Immersion Assembly, 5 x 1”OD standpipe, with 1” compression fi1ng and T-Handle1000260-99 Immersion Assembly, User supplied standpipe, with 1” Compression fi1ng and T-Handle1000280-1 Flow Through Tee, 4” PVC tee base reduced to 2” FNPT entries3600066.NY 1” MNPT Nylon Gland Fi1ng7” x 0.98”(178 mm x 25 mm) Flow Through Cell Immersion Assembly