Turquoise Switch

ASQ11ds_62003_0050_en_asq1: 290312Jpage 1ORDERING INFORMATIONULTRA-LONG STROKE, HIGH CONTACT RELIABILITY SEALED SWITCHES (SAME SIZE AS J TYPE)TURQUOISE SWITCHESASQ TYPE (mm)FEATURES1. Same size as J type with ultra-long stroke. For pin plunger type, it maintains an ultra-long stroke O.T. (Over Travel) with over 2.2 mm on the NO side and over 2.5 mm on the NC side. Variations in operation can be absorbed.2. Since contact pressure does not depend on the operation stroke, the range of possible use over the entire stroke is greatly increased.(Please refer to operation concept diagram.)3. High contact reliability to support low level switching loadsHigh contact reliability is maintained with gold plating on both sides of sliding contact.4. Highly effective sealing for resistance against adverse environmentsImmersion protection type• JIS C0920 (water-resistance experiments for electrical machines and protection rating against incursion of solid substances)D2• JIS D0203 (method for testing moisture resistance and water resistance in automotive components)IP67• IEC529 (rating for outer shell protection)5. Silent operationWith sliding contact construction there is no operation noise.6. Direct operation possible from lateral direction with pin plunger (lever-less operation allows space savings)7. Contains no harmful substances (mercury, lead, hexivalent chromium, cadmium)TYPICAL APPLICATIONS1. Automobiles (detection of door opening and closing and shift lever position, etc.)2. Household appliances (propane stoves, vacuum cleaners, air conditioners, washing machines, etc.)13.310.15.4Type of switchASQ1: TurquoisestrokeswitchSize of mounting hole0: 1: 4: 5: 6: 7: 3 mm standard type3 mm without boss typeRight side pin type (solder terminal only) Left side pin type (solder terminal only)Right 2 boss type (solder terminal only)Left 2 boss type (solder terminal only)Terminal2: 3: 4: 5: 6: 7: 8: Wire leads right side type (NC and NO type only)Wire leads left side type (NC and NO type only)Solder terminalPC board terminalWire leads (bottom type)PC right angle terminalPC left angle terminalContact form1: 2: 3: SPDTSPST-NC (wire lead type only)SPST-NO (wire lead type only)Actuator0: 7: 8: Pin plungerLeaf leverSimulated leafleverEx. ASQ1Remark: Not every combination is available. Please refer to the following table, “PRODUCT TYPES”.ASQ12 ds_62003_0050_en_asq1: 290312JOPERATION CONCEPT DIAGRAM (reference)APPLICABLE CURRENT RANGE (reference)PRODUCT TYPES1. Terminal type (Mounting hole: 3mm standard type/3mm without boss type/2 boss type/Side pin type)2. Wire leads bottom type (Mounting hole: 3mm standard type)3. Wire leads side type (Mounting hole: 3mm standard type)Actuator Operating force Max.Mounting hole: 3mm standard typeMounting hole: 3mm without boss typeRight 2 boss typeLeft 2 boss typeRight side pin typeLeft side pin typeSolder terminalPC right angle terminalPC left angle terminalPC board terminalSolder terminalSolder terminalSolder terminalSolder terminalPin plunger 1.5N ASQ10410 ASQ10710 ASQ10810 ASQ11510 ASQ16410 ASQ17410 ASQ14410 ASQ15410Leaf lever 1.7N ASQ10417 ASQ10717 ASQ10817 ASQ11517 ASQ16417 ASQ17417 ASQ14417 ASQ15417Simulated leaf lever 1.5N ASQ10418 ASQ10718 ASQ10818 ASQ11518 ASQ16418 ASQ17418 ASQ14418 ASQ15418Actuator Operating force Max.Wire leads bottom type (Mounting hole: 3mm standard type)Switching type NC type NO typePin plunger 1.5N ASQ10610 ASQ10620 ASQ10630Leaf lever 1.7N ASQ10617 ASQ10627 ASQ10637Simulated leaf lever 1.5N ASQ10618 ASQ10628 ASQ10638Actuator Operating force Max.Wire leads right side type (Mounting hole: 3mm standard type)Wire leads left side type (Mounting hole: 3mm standard type)NC type NO type NC type NO typePin plunger 1.5N ASQ10220 ASQ10230 ASQ10320 ASQ10330Leaf lever 1.7N ASQ10227 ASQ10237 ASQ10327 ASQ10337Simulated leaf lever 1.5N ASQ10228 ASQ10238 ASQ10328 ASQ10338Contact form: terminal typeTFRFOFStrokeOperation loadContact pressureRange of possible useOperationloadNC sideNO sideRP (NC)OP (NC)OT (NC)OT (NO) TTPOP (NO)FPRP (NO)Standard (mounting boss and hole center diameter or standoff)0NC sideNO side0(OFF)CONTACT ARRANGEMENT 1. SPDTCOM NO NC2. SPST-NC (Wire leads type only)3. SPST-NO (Wire leads type only)COM NC COM NOApplicable range100mA1mA030V5VDCASQ13ds_62003_0050_en_asq1: 290312JRATING1. Rating1 mA, 5 V DC to 100 mA, 30 V DCNote: Please consult us regarding 42 V DC rating.2. Operation environment and conditionsNote: When switching at low and high speeds or under vibration, or in high-temperature, high-humidity environments, life and performance may be reduced significantly depending on the load capacity. Please consult us.3. Electrical characteristics4. CharacteristicsNotes: As long as there are no particular designations, the following conditions apply to the test environment.• Ambient temperature: 5 to 35°C• Relative humidity: 25 to 85% RH• Air pressure: 86 to 106 kPa5. Protective structure1) JIS C0920: Waterproof typeA concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 30 minutes under 1 m of water (with temperature difference between water and switch no larger than 5°C).2) IEC 60529: IP67 (waterproof type)A concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 30 minutes under 1 m of water (with temperature difference between water and switch no larger than 5°C).3) JIS D0203: Equivalent of D2A concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 30 minutes under 10 cm of water (with temperature difference between water and switch no larger than 30°C).Note: Names of the standards can be found in the section describing features.Item SpecificationsAmbient and storage temperature –40°C to +85°C (no freezing and condensing)Allowable operating speed 30 to 500 mm/sec.Max. operating cycle rate 120 cpmWithstand voltage (Initial) Between non-continuous terminals: 600 Vrms, Between each terminal and other exposed metal parts: 1,500 Vrms, Between each terminal and ground: 1,500 Vrms (at detection current of 1 mA)Insulation resistance (Initial) Min. 100 M? (at 500 V DC insulation resistance meter) (Locations measured same as withstand voltage.)Contact resistance (Initial) Max. 1? (By voltage drop 0.1 A 6 to 8 V DC)Item SpecificationsElectrical switching life5 V DC 1 mA (resistive load) Min. 5 ? 105 Switching frequency: 20 times/min.Conduction ratio: 1:1Pushbutton operation speed: 100 mm/sPushbutton switching position: free position (FP) to operation limit position (TTP)16 V DC 50 mA (resistive load) Min. 5 ? 10530 V DC 100 mA (resistive load) Min. 2 ? 105Vibration resistance(malfunction vibration resistance)Single amplitude: 0.75 mmAmplitude of vibration: 10 to 55 Hz (4 minutes cycle)Direction and time: 30 minutes each in X, Y and Z directionsAmplitude of vibration: 5 to 200 Hz (10 minutes cycle)Acceleration: 43.1 m/s2Direction and time: 30 minutes each in X, Y and Z directionsShock resistance(malfunction shock resistance)Shock value: 980 m/s2Direction and time: 5 times each in X, Y and Z directionsVibration resistance endurance Frequency of vibration: 33.3 Hz, Acceleration: 43.1 m/s2Direction and time: 8 hours each in X, Y and Z directionsTerminal strength 6 N min. (each direction) *Terminal deformation possible.Heat resistance 85°C 500 houresCold resistance –40°C 500 houresHumidity resistance 40°C 95% RH 500 houresHigh-temperature, high-humidity resistance 85°C 85% RH 500 houresThermal shock resistance 30 min. at 85°C to 30 min at –40°C for 1,000 cyclesWater resistance IP67 (Wire leads type)ASQ14 ds_62003_0050_en_asq1: 290312J6. Operating characteristicsNotes: 1. The above indicates the characteristics when operating the pushbutton from the vertical direction.2. Indicates operation load for NO contact to achieve ON status.3. Indicates position for NC contact to achieve OFF status.4. Indicates position for NO contact to achieve ON status.5. Indicates position for NC contact to achieve ON status.6. Indicates position for NO contact to achieve OFF status.DIMENSIONSActuator Pin plunger Leaf lever Simulated leaf leverOperating Force (max. O.F.) *Note 2 1.5N 1.7N 1.5NTotal travel Force (max. T.F.) (reference value) (2.0N) (3.1N) (2.8N)Free Position (max. F.P.)From mounting boss and hole center line 9.2mm 11.5mm 14.4mmFrom standoff 13.4mm 15.7mm 18.6mmOperating Position on NC sideO.P. (N.C.) *Note 3From mounting boss and hole center line 8.7±0.3mm 9.8±0.5mm 12.5±0.5mmFrom standoff 12.9±0.3mm 14.0±0.5mm 16.7±0.5mmOperating Position on NO sideO.P. (N.O.) *Note 4From mounting boss and hole center line 8.4±0.3mm 9.3±0.5mm 12.0±0.5mmFrom standoff 12.6±0.3mm 13.5±0.5mm 16.2±0.5mmRelease Position on NC sideR.P. (N.C.) *Note 5From mounting boss and hole center line 8.8±0.3mm 10.1±0.5mm 12.9±0.5mmFrom standoff 13.0±0.3mm 14.3±0.5mm 17.1±0.5mmRelease Position on NO sideR.P. (N.O.) *Note 6From mounting boss and hole center line 8.5±0.3mm 9.6±0.5mm 12.4±0.5mmFrom standoff 12.7±0.3mm 13.8±0.5mm 16.6±0.5mmOver travel on N.C. side (min. O.T. (N.C.)) 2.5mm 3.1mm 3.3mmOver travel on N.O. side (min. O.T. (N.O.)) 2.2mm 2.6mm 2.8mmTotal Travel Position (T.T.P.) (reference value)From mounting boss and hole center line (5.9mm) (6.2mm) (8.7mm)From standoff (10.1mm) (10.4mm) (12.9mm)Interested in CAD data? You can obtain CAD data for all products with a mark from your local Panasonic Electric Works representative.CAD Datamm General tolerance: ±0.251. Terminal type: Mounting hole 3mm, standard typePin plungerCAD Data1.9 dia.FP 13.4 MAX.OP (NC) 12.90.3RP (NC) 13.00.3OP (NO) 12.60.3RP (NO) 12.70.3TTP (10.1)FP 9.2 MAX.OP (NC) 8.70.3RP (NC) 8.80.3OP (NO) 8.40.3RP (NO) 8.50.3TTP (5.9)1.28.40.22.05.40.155.40.44.530.152.74.530.153.20.14.113.30.15C0.30.41.53.0+0.1–0 3.0+0 –0.1 dia.8.30.13.7 4.25.95.13.0+0.3–0.2Operating Force (max. O.F.) 1.5NFree Position (max. F.P.)From mounting boss and hole center line 9.2mmFrom standoff 13.4mmOperating Position on NC side O.P. (N.C.)From mounting boss and hole center line 8.7±0.3mmFrom standoff 12.9±0.3mmOperating Position on NO side O.P. (N.O.)From mounting boss and hole center line 8.4±0.3mmFrom standoff 12.6±0.3mmRelease Position on NC side R.P. (N.C.)From mounting boss and hole center line 8.8±0.3mmFrom standoff 13.0±0.3mmRelease Position on NO side R.P. (N.O.)From mounting boss and hole center line 8.5±0.3mmFrom standoff 12.7±0.3mmOver travel on N.C. side (min. O.T. (N.C.)) 2.5mmOver travel on N.O. side (min. O.T. (N.O.)) 2.2mmASQ15ds_62003_0050_en_asq1: 290312JLeaf leverNote: When switching at high speed or under shock, lever endurance may drop. Therefore, please be sure to conduct an endurance evaluation under actual switching conditions.1.9 dia.FP 15.7 MAX.FP 11.5 MAX.14.0(18)TTP (10.4)3.3OP (NO) 9.30.5RP (NO) 9.60.5OP (NC) 9.80.5RP (NC) 10.10.5OP (NC) 14.00.5RP (NC) 14.30.5OP (NO) 13.50.5RP (NO) 13.80.5TTP (6.2)0.5C0.31.28.40.22.05.40.155.40.44.530.152.74.530.154.113.30.153.0+0.3–0.23.0+0.1–0 4.23.75.95.11.20.41.5R1.33.0+0 –0.1 dia.8.30.13.20.1CAD DataOperating Force (max. O.F.) 1.7NFree Position (max. F.P.)From mounting boss and hole center line 11.5mmFrom standoff 15.7mmOperating Position on NC side O.P. (N.C.)From mounting boss and hole center line 9.8±0.5mmFrom standoff 14.0±0.5mmOperating Position on NO side O.P. (N.O.)From mounting boss and hole center line 9.3±0.5mmFrom standoff 13.5±0.5mmRelease Position on NC side R.P. (N.C.)From mounting boss and hole center line 10.1±0.5mmFrom standoff 14.3±0.5mmRelease Position on NO side R.P. (N.O.)From mounting boss and hole center line 9.6±0.5mmFrom standoff 13.8±0.5mmOver travel on N.C. side (min. O.T. (N.C.)) 3.1mmOver travel on N.O. side (min. O.T. (N.O.)) 2.6mmSimulated leaf leverNote: When switching at high speed or under shock, lever endurance may drop. Therefore, please be sure to conduct an endurance evaluation under actual switching conditions.2.8FP 14.4 MAX.FP 18.6 MAX.1.9dia.15.0R2.0TTP (8.7)OP (NO) 12.00.5RP (NO) 12.40.5OP (NC) 12.50.5RP (NC) 12.90.5TTP (12.9)OP (NO) 16.20.5RP (NO) 16.60.5OP (NC) 16.70.5RP (NC) 17.10.5(18)3.3R1.30.5C0.31.28.40.22.05.40.155.40.44.530.152.74.530.154.113.30.153.0+0 –0.1 dia.1.50.48.30.13.0+0.3–0.24.25.93.75.13.0+0.1–0 1.23.20.1CAD DataOperating Force (max. O.F.) 1.5NFree Position (max. F.P.)From mounting boss and hole center line 14.4mmFrom standoff 18.6mmOperating Position on NC side O.P. (N.C.)From mounting boss and hole center line 12.5±0.5mmFrom standoff 16.7±0.5mmOperating Position on NO side O.P. (N.O.)From mounting boss and hole center line 12.0±0.5mmFrom standoff 16.2±0.5mmRelease Position on NC side R.P. (N.C.)From mounting boss and hole center line 12.9±0.5mmFrom standoff 17.1±0.5mmRelease Position on NO side R.P. (N.O.)From mounting boss and hole center line 12.4±0.5mmFrom standoff 16.6±0.5mmOver travel on N.C. side (min. O.T. (N.C.)) 3.3mmOver travel on N.O. side (min. O.T. (N.O.)) 2.8mmmm General tolerance: ±0.25ASQ16 ds_62003_0050_en_asq1: 290312J2. Right side pin type (Solder terminal only)Mounting hole: 3 mm without boss type PC board terminalPC board patternCAD Data0.95.080.155.080.153.0+0.3-0.2C0.25.080.15.080.11.0+0.1-0 dia.8.3±0.1C 0.28.32.6±0.052.2±0.05 dia.2.6±0.055.01.9 dia.0.41.5FP 13.4 MAX.RP (NC) 13.0±0.3OP (NC) 12.9±0.3RP (NO) 12.7±0.3OP (NO) 12.6±0.3TTP (10.1)FP 9.2 MAX.RP (NC) 8.8±0.3OP (NC) 8.7±0.3RP (NO) 8.5±0.3OP (NO) 8.4±0.3TTP (5.9)5.15.94.23.7-0.2+0.33.01.22.05.4±0.155.40.44.53±0.152.74.53±0.154.113.3±0.15CAD DataASQ17ds_62003_0050_en_asq1: 290312JLeft side pin type (Solder terminal only) mm General tolerance: ±0.25Right 2 boss type (Solder terminal only)Left 2 boss type (Solder terminal only)8.3±0.1C 0.28.32.6±0.052.2±0.05 dia.2.6±0.055.01.9 dia.0.41.5FP 13.4 MAX.RP (NC) 13.0±0.3OP (NC) 12.9±0.3RP (NO) 12.7±0.3OP (NO) 12.6±0.3TTP (10.1)FP 9.2 MAX.RP (NC) 8.8±0.3OP (NC) 8.7±0.3RP (NO) 8.5±0.3OP (NO) 8.4±0.3TTP (5.9)5.15.94.23.7-0.2+0.33.01.22.05.4±0.155.40.44.53±0.152.74.53±0.154.113.3±0.15CAD Data8.3±0.12-3.0 dia.C0.31.51.9 dia.0.41.5FP 13.4 MAX.RP (NC) 13.0±0.3OP (NC) 12.9±0.3RP (NO) 12.7±0.3OP (NO) 12.6±0.3TTP (10.1)FP 9.2 MAX.RP (NC) 8.8±0.3OP (NC) 8.7±0.3RP (NO) 8.5±0.3OP (NO) 8.4±0.3TTP (5.9)5.15.94.23.7-0.2+0.33.01.22.05.4±0.155.40.44.53±0.152.74.53±0.154.113.3±0.15-0.1+0CAD DataC0.32-3.0 dia.8.30.11.51.9 dia.0.41.5FP 13.4 MAX.RP (NC) 13.0±0.3OP (NC) 12.9±0.3RP (NO) 12.7±0.3OP (NO) 12.6±0.3TTP (10.1)FP 9.2 MAX.RP (NC) 8.8±0.3OP (NC) 8.7±0.3RP (NO) 8.5±0.3OP (NO) 8.4±0.3TTP (5.9)5.15.94.23.7-0.2+0.33.01.22.05.4±0.155.40.44.53±0.152.74.53±0.154.113.3±0.15-0.1+0CAD DataASQ18 ds_62003_0050_en_asq1: 290312J3. Angle terminal type: mounting hole 3 mm, standard type mm General tolerance: ±0.25Right typeLeft type: mounting hole 3 mm, standard typeC 0.25.08±0.155.08±0.150.92.0FP 9.2 MAX.RP (NC) 8.8±0.3OP (NC) 8.7±0.3RP (NO) 8.5±0.3OP (NO) 8.4±0.3TTP (5.9)5.15.94.23.78.4±0.25.42.73.0 dia.8.3±0.13.2±0.1-0+0.13.013.3±0.15NCCOM NO6.0±0.30.43.1±0.44.1C0.31.9 dia.5.4±0.15-0.1+0CAD DataC 0.23.0 dia.5.08±0.155.08±0.15COM 0.9 NO NC13.3±0.155.42.73.2±0.11.9 dia.5.4±0.158.4±0.2RP (NO) 8.5±0.3OP (NO) 8.4±0.3RP (NC) 8.8±0.3OP (NC) 8.7±0.3FP 9.2 MAX.TTP (5.9)8.3±0.12.03.1±0.44.10.44.25.95.13.0 -0+0.13.7 6.0±0.3C0.3-0.1+0CAD DataASQ19ds_62003_0050_en_asq1: 290312J4. Wire leads bottom type: Mounting hole 3mm, standard type mm General tolerance: ±0.255. Wire leads right side type: Mounting hole 3mm, standard type4.23.62.63.2R 0.3R 0.31.9 dia.1.4 dia.*Wire lead thicknessWire lead color::::0.3mm2COMNCNO··················BlackRedWhite8.40.25.40.15C 0.33.0+0-0.1 dia.TTP (5.9)OP (NO) 8.40.3OP (NC) 8.70.3FP 9.2 MAX.5.93.74.32.2300105.028.30.15.13.20.12.75.413.33.0+0.1-0CAD DataR 2.01.9 dia.8.40.25.40.15C 0.3R 0.5R 0.5R 0.5TTP (5.9)OP (NO) 8.40.3OP (NC) 8.70.3 FP 9.2 MAX.5.93.71.4 dia.4.55.24.3300102.45.028.30.15.13.20.12.75.413.33.0+0.1-03.0+0-0.1 dia.*Wire lead thicknessWire lead color::::0.3mm2COMNCNO··················BlackRedWhiteCAD DataASQ110 ds_62003_0050_en_asq1: 290312J6. Wire leads left side type: Mounting hole 3mm, standard type mm General tolerance: ±0.25NOTES1.9 dia.8.40.25.40.15C 0.3R 0.5R 0.5TTP (5.9)OP (NO) 8.40.3OP (NC) 8.70.3FP 9.2 MAX.5.93.71.4 dia.4.55.25.024.38.30.15.13.20.12.75.413.33.0+0.1-030010 2.4R 0.53.0+0-0.1 dia.*Wire lead thicknessWire lead color::::0.3mm2COMNCNO··················BlackRedWhiteCAD Data1. Soldering conditionsThe application of excessive heat upon the switch when soldering can cause degradation of switch operation. Therefore, be sure to keep within the conditions given below.1) Manual soldering: use soldering irons (max. 350°C, within 3 seconds) capable of temperature adjustment. This is to prevent deterioration due to soldering heat. Care should be taken not to apply force to the terminals during soldering.2) Automatic soldering: Soldering must be done as below;260°C: within 6 seconds350°C: within 3 seconds2. MountingPlease avoid use in which load would be applied to the sides (hatch part (both sides) shown below) of the switch in the direction indicated by the arrows. This could cause erroneous operation. Also, when using a metal installation board, please make allowance for burr direction designation and burr suppressing, etc., so that the burr side will not be on the switch installation side.1) To secure the switch, please use an M3 small screw on a flat surface and tighten using a maximum torque of 0.29 N·m. It is recommended that spring washers be used with the screws and adhesive be applied to lock the screws to prevent loosening of the screws. Please make sure not to apply adhesive onto the moving parts.2) Be sure to maintain adequate insulating clearance between each terminal and ground.3) Although it is possible to directly operate the pin plunger type from the lateral direction, please consult us if doing so.4) After mounting please make sure no tensile load will be applied to the switch terminals.5) Range of possible use: Please set the operation position to within the ranges in the following table so that there is sufficient insulation distance and to maintain contact reliability.mm6) PC board terminal type should be used if the products are to be soldered on the PC board. Solder terminal type is not for soldering on PC board.3. Cautions regarding the circuit1) In order to prevent malfunction in set devices caused by bounce and chattering during the ON-OFF switch operation, please verify the validity of the circuit under actual operating conditions and temperature range.2) When switching inductive loads (relays, solenoids, buzzers, etc.), an arc absorbing circuit is recommended to protect the contacts.4. Please verify under actual conditions.Please be sure to conduct quality verification under actual operating conditions in order to increase reliability during actual use.5. Switch selectionPlease make your selection so that there will be no problems even if the operating characteristics vary up to ±20% from the standard values.ActuatorPlunger/lever freeFrom mounting boss and hole center lineFrom standoffPin plunger >9.2 >13.4Leaf lever >10.7 >14.9Simulated leaf lever >13.5 >17.7ActuatorPlunger/Lever pushedFrom mounting boss and hole center lineFrom standoffPin plunger 7.8 to 5.9 12.0 to 10.1Leaf lever 8.4 to 6.2 12.6 to 10.4Simulated leaf lever 11.1 to 8.7 15.3 to 12.9ASQ111ds_62003_0050_en_asq1: 290312J6. Oil-proof and chemical-proof characteristicsThe rubber cap swells when exposed to oil and chemicals. The extent of swelling will vary widely depending on the type and amount of oil and chemicals.Check with the actual oil or chemicals used.In particular, be aware that solvents such as freon, chlorine, and toluene cannot be used.7. Environment• Although continuous operation of the switch is possible within the range of ambient temperature (humidity), as the humidity range differs depending on the ambient temperature, the humidity range indicated below should be used.Continuous use near the limit of the range should be avoided.• This humidity range does not guarantee permanent performance.8. Other1) Please remember that this switch cannot be used under water. Also, pleased be warned that switching and sudden temperature changes with the presence of water droplets can cause seepage into the unit.2) Keep away from environments where silicon based adhesives, oil or grease are present as faulty contacts may result from silicon oxide. Do not use in areas where flammable or explosive gases from gasoline and thinner, etc., may be present.3) When using the lever type, please be careful not to apply unreasonable load from the reverse or lateral directions of operation.4) Do not exceed the total travel position (TTP) and press the actuator. This could cause operation failure. Also, when switching at high speed or under shock even within the operation limit, the working life may decrease. Therefore, please be sure to verify the quality under actual conditions of use.5) Please make considerations so that the switch does not become the stopper for the moving part.Acceptable range(Avoidcondensation whenused at temperatureshigher than 0°C)(Avoid freezing whenused at temperatureslower than 0°C)95505–40 0 +85Temperature, °CHumidity, %R.H.