Water-Fine™ Series Filter Cartridges Brochure (PDF 118 KB)

Data Sheet E-2135-CWATER-FINE™ SeriesFilter CartridgesDI and High Purity Water Filter• Proprietary Highly Asymmetric Polysulfone MembraneMedia• Absolute Rated at >99.9% Efficiency with RetentionRatings from 0.05 to 1.2 µm• Superior Flow Rates and Long Service Life• High Purity Polypropylene Hardware• End Configurations to Fit Most HousingsPerformance SpecificationsFilter Grades (>99.9% Retention Rating by StandardLatex Bead Challenge):0.05, 0.1, 0.2, 0.45, 0.65, 0.8, 1.2 µmMaximum Differential Pressure:70 psid (4.8 bard) @ 120°F (49°C)50 psid (3.4 bard) @ 180°F (82°C)Recommended Change Out Differential Pressure1:35 psid (2.4 bard)FDA Listed Materials:Manufactured from materials, which are FDA listed for foodcontact applications in Title 21 of the U.S. Code of FederalRegulations.Sanitizing Agents:Cartridge may be sanitized in place with common oxidizingagents. Consult factory for compatibility information.Rinse-Up:Cartridges will rinse-up to 18 Megohm-cm with a minimumof throughput.Pre-Rinsing:A pre-rinse is available upon request. Specify code 314 at endof Water-Fine description.Product SpecificationsMaterials of Construction:Filter Media: Highly Asymmetric Polysulfone MembraneSupport Material: PolypropyleneHardware: PolypropyleneSurface Treatment: HydroxypropylcelluloseSealing: Thermal BondGaskets/O-rings: Silicone Elastomer, EPDM, Buna N,Viton2 A, FEP Encapsulated SiliconeDimensions (nominal):Outside Diameter: 2 3/5" (6.6 cm)Lengths: 4" (10.2 cm), 9 3/4" (24.8 cm), 10" (25.4 cm), 19 1/2" (49.5 cm), 20" (50.8 cm), 29 1/4" (74.3 cm),30" (76.2 cm), 39" (99.1 cm), 40" (102 cm)Surface Area: 6.1 ft2 (0.57 m2) per 10" (25.4 cm)equivalentProduct Applications• Pre and Post Filter for DI Water• Point-of-Use Filter for DI Water• Filtration of Aqueous Chemical Solutions1 - Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.2 - Registered trademark of DuPont Dow.2200 Northern Boulevard.East Hills, New York 11548-1289 1.800.FILTERS toll free516.484.5400 phone516.484.3216 faxinformation@pall.com e-mailVisit us on the Web at www.pall.comPall Corporation has offices and plants throughout the world in locations including:Argentina, Australia, Austria, Belgium, Brazil, Canada, China, France, Germany, Hong Kong,India, Indonesia, Ireland, Italy, Japan, Korea, Malaysia, Mexico, the Netherlands, New Zealand,Norway, Poland, Puerto Rico, Russia, Singapore, South Africa, Spain, Sweden, Switzerland,Taiwan, Thailand, United Kingdom, United States, and Venezuela. Distributors are located inall major industrial areas of the world.© Copyright 2005, Pall Corporation. Pall, and Water-Fine are trademarks of Pall Corporation. ® Indicates a Palltrademark registered in the USA. is a service mark of Pall Corporation.Bulletin #E-2135-4C 1/05Code Filter n Grades0.05 0.05 µm0.1 0.1 µm0.2 0.2 µm0.45 0.45 µm0.65 0.65 µm0.8 0.8 µm1.2 1.2 µmPart Numbers/Ordering InformationWFN n – l U u – t z (e.g., WFN0.2–10US-M3 314)Code Cartridge l Lengths(nominal)4 4"9.75 9.75"10 10"19.5 19.5"20 20"29.25 29.25"30 30"39 39"40 40"Code Gasket/O-ringu MaterialsS Silicone (standard O-rings)E EPDMV Viton AN Buna N (standard gaskets)T FEP Encapsulated SiliconeX No O-ring required (M2 only)Code End ConfigurationstBlank DOE with elastomer gasket seals & end caps1X DOE, 1" (2.54 cm) extended coreM2 SOE flat closed end fits housing with 020 O-ring postM3 SOE flat closed end, external 222 O-rings(retrofits other manufacturers’ Code 0) 3M5 DOE, internal 120 O-rings (retrofits 213 O-ring style) 3M6 SOE flat closed end, external 226 O-rings(retrofits other manufacturers’ Code 6) 3M7 SOE fin end, external 226 O-rings (retrofits other manufacturers’ Code 7) 3M8 SOE fin end, external 222 O-rings (retrofits other manufacturers’ Code 5) 3M10 DOE, internal O-rings (fits other manufacturers’housings) 3M11 SOE flat closed end, internal 120 O-ring(retrofits other manufacturers’ X-style) 3M20 SOE, internal O-ring (same as M10), closed end with deep recessLiquid Flow SpecificationsFilter Grade (µm) DI Water Flowper 1 psid (gpm/10" (25.4 cm) equivalent)0.05 1.0 (3.8 lpm)0.1 1.7 (6.4 lpm)0.2 3.0 (11.4 lpm)0.45 5.5 (20.8 lpm)0.65 6.0 (22.7 lpm)0.8 7.0 (26.5 lpm)1.2 8.0 (30.3 lpm)Code Pre-Rinsez OptionBlank No Pre-Rinse314 Pre-Rinse3 - For details, contact Pall Corporation.