Zelite(TM) Polyethylene Tubing Brochure

ZeliteLinear Low Density Polyethylene Tubing™®Flu id Transfer Specia l is ts ®DISTRIBUTOR PARTNER 800-50-NEWAGE(800-506-3924) 215-526-2300Fax: 800-837-1856215-526-2190info@newageindustries.com145 James WaySouthampton, PA 18966www.newageindustries.com®Zelite™L i n e a r L o w D e n s i t y P o l y e t h y l e n e T u b i n gwww.newageindustries.comZelite, Newloc, NewAge, “Fluid Transfer Specialists,” and The "N" Logo are trademarks of NewAge® Industries, Inc.NOTICE: NewAge Industries, Inc. has been a privately owned corporation since 1954. Neither the corporation nor its principals are affiliated, in any way, with any other group or entity either representing themselves as or being referred to by the term New-Age.WARRANTY: NewAge Industries’ products are warranted to be free from defects in material and workmanship. Any product found to carry such defects will be replaced without charge. This warranty is limited only to the replacement of NewAge Industries' products, item for item, which after examination byNewAge Industries are deemed defective. NewAge Industries specifically disclaims any other liability. The data supplied is provided as a helpful guideline and is believed to be reliable; however, nothing stated shall constitute a guarantee, recommendation, or warranty for any application.7/20/10© NewAge Industries, Inc. 2010 Specifications are subject to change without notice.¦ Made from non-toxic ingredients conforming to FDA standards¦ Does not impart a taste or odor to critical streams¦ Flexible, lightweight, durable¦ Translucent natural or opaque colors¦ Made from 100% virgin grade raw materials¦ Good dielectric properties¦ Offers enhanced resistance to stress cracking¦ Chemically inert; forms a good barrier to gases,vapors, and moistureNotesZELITE conforms to the applicableregulations of the FDA for use of articlesintended for contact with food. Theincreased tensile strength of ZELITE LinearLow Density, over that of a low densitypolyethylene, enhances its resistance tosplitting during use.FEP-lined polyethylene, offering superiorpurity at a very reasonable cost, is availablethrough minimum order. Medium-high andultra-high density polyethylene material isavailable through minimum order. Call fordetails on these custom products.Physical Properties**Hardness, Shore D ±5 50Tensile Strength, psi 2250Elongation at Break, % 600Brittle Temperature, °F -76Vicat Softening Point, °F 196Maximum Operating Temperature, °F 140**Values listed are typical for the material used inmanufacture, except where noted, and are meant only asa guide to aid in design. Field testing should beperformed to find the actual values for your application.Recommended Fittings ¦ Newloc® push-to-connect fittings LBS.PER100 FT.1.051.051.471.472.02.02.52.53.53.54.45.413.77.417.621.525.5WORKINGPSI AT 70°F135135180180140140120120909070609045725950ID(IN.).170.1701/81/83/163/161/41/43/83/81/25/83/47/811-1/41-1/2WALL(IN.).040.0401/161/161/161/161/161/161/161/161/161/161/81/161/81/81/8OD(IN.)1/41/41/41/45/165/163/83/81/21/25/83/4111-1/41-1/21-3/4STD.LENGTH (FT.)5001005001005001005001005001001001001001001005050PART NO.NATURAL251 0571251 0571251 0256251 0256251 0886251 0886251 1201251 1201251 2146251 2146251 2293251 2398251 2713251 2818251 2923251 3028251 3133PART NO.BLACK251 0529251 0214251 1159251 2104251 2279PART NO.RED251 0606251 1236PART NO.YELLOW251 0627251 1257LBS.PER100 FT.1.052.5WORKINGPSI AT 70°F135120ID(IN.).1701/4OD(IN.)1/43/8BURSTPSI AT 70°F540540720720560560480480360360280240360180288236200BURSTPSI AT 70°F540480Add length suffix to part number when ordering. Example: 500 ft. of .170” I.D. x 1/4” O.D.black color tubing is part number 251 0529-500.BOLD indicates the critical dimension for fittings application.WALL(IN.).0401/16LBS.PER100 FT.1.052.5WORKINGPSI AT 70°F135120ID(IN.).1701/4OD(IN.)1/43/8BURSTPSI AT 70°F540480WALL(IN.).0401/16PART NO.BLUE251 0543251 1173PART NO.GREEN251 0557251 1187Red, yellow, green, and blue color tubing is sold by standard coil length only (500 ft.).Add length suffix to part number when ordering. Example: 500 ft. of .170” I.D. x 1/4” O.D.red color tubing is part number 251 0606-500.BOLD indicates the critical dimension for fittings application.Made in U.S.A.Custom Services¦ Cut ¦ Size ¦ Color ¦ Heat-Form ¦ And MoreCall for more information: 800-506-3924 or 215-526-2300