Only show results available in Connecticut? Ok

Dust Filtration Applications

  • Premium

    Emission control & air dedusting for Fertilizers

    The recovery of fertilizers typically after drying tunnels or drum dryers is associated with a high load of particulates and very humid gas streams. The recovery of these products is commonly performed by dryer cyclones as they allow for a direct powder capture and avoid filter clogging due to condensation. Arrangements with cyclones and/or with bag filters are usual in the ...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Emission control solutions for oil & gas industry

    In Fluid Catalytic Cracking (FCC)processes, widely used in oil refineries, the separation and recovery of powder catalysts is a major concern. Particularly, the concentration of catalyst after the FCC regenerator is usually over 150 mg/Nm3. Since these levels of emissions didn't represent any environmental harm in the past, they were not controlled by any separator or filter. Plant managers main concern was to clean a fraction of the gas to produce energy in a Turbo Expander, or similar, while concentrating the ...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Emission control solutions for pyrolisis, incineration and gasification sector

    For PM emission control in very high temperature exhaust streams ( >600ºC ), such as gasification, pyrolysis and incineration, traditional bag filters following temperature exchangers, ceramic filters, or scrubbers are used as end stage dedusters. For most arrangements, a primary high temperature separator, namely a cyclone, is important to reduce as much ash and char as possible. A good efficiency is important to reduce concentration of solids to the final stage dedusters, avoiding plugging of scrubbers ...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Emission control solutions for clinker cooler and pre-heater dedusting sector

    The control of clinker fines emissions after the heatexchanger, placed downstream of the clinkercooler,is usually a problem for cementplant managers. The process is characterized by high material abrasiveness, high loads and variable flow ratein normal and maximum ...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Emission control solutions for biomass and coal combustion sector

    For particulate matter (PM) emission control in high temperature exhaust streams, such as those from biomass or coal boilers and heaters, common dedusters such as cyclones and multicyclones are not able to comply with current emission limits. This is mainly due to their low efficiency, particularly for small particles (less than 10µm). In order to meet emission limits this usually requires an additional investment in a final stage deduster. Bag filters (BF) are very efficient dedusters. They can also be very ...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Emission control solutions for steel and ferroalloys sector

    Steel and ferroalloysmanufacturing processes involve high temperature exhaust streams, often at more than 900ºC. Typically, the gas flows from the furnace (usually electric arch type) and goes into a gas conditioning tower to cool down below 200ºC so that it can be treated by a Bag Filter. It's also common to have ESP´s as end dedusters that can be preceded by a multicyclone serving as ...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Emission control solutions for fuel oil combustion sector

    For PM emission control in high temperature exhaust streams, such as those from fuel oil boilers, common dedusters like Bag filters, have very high maintenance costs. The diesel and fuel oil fly ash can be quite sticky and clog to filter elements, which can be minimized with costly protection reagents or frequent filter elements changes. Flue gas cooling is needed in front of the filter when temperatures are higher than 200 ...

    By Advanced Cyclone Systems, S. A. based in Porto, PORTUGAL.

  • Premium

    Solutions for composite dust extraction

    Dust control in the composites industry tends, for us, to fall into two categories. GRP and similar bulk manufacture produces large volumes of dust, while CFRP work tends to be more precise and produces only trimming/finishing dusts In either case, operators are more effective where PPE is less intrusive. In almost every case, AirBench can reduce or remove the requirement for PPE. For CFRP, we recommend our FN type with our two-stage ‘F’ type filters; these provide a very high level of protection ...

    By AirBench Ltd. based in Colchester, UNITED KINGDOM.

  • Premium

    Engineered clean air solutions for transportation applications

    From alternating between initial paint sprays and repairs with finishing and coating applications, you’re too busy to worry if your shop floor air is OSHA or EPA compliant. You want to protect your employees against sanding dust and spray fumes, but facility-wide HVAC systems can suck the air out of your bottom line. What if you had a cost-effective, clean air solution that could protect your employees from airborne hazards and even speed up drying times for a more efficient work ...

    By Duroair Technologies Inc. based in Niagara Falls, ONTARIO (CANADA).

  • Premium

    Industrial screening solutions for cosmetics industry

    The value of the global cosmetics industry is projected to reach more than $267 billion by 2017. With this growth has come an increased consumer awareness of quality and a strong need for organizations to deliver exceptional product control to remain competitive. Industrial cosmetics sieves play an important role in filtering out impurities without the use of harsh chemicals, while minimizing product loss. Investing in quality equipment is a great way to help your organization deliver superior products and ...

    By VibraScreener Inc. based in Charlotte, NORTH CAROLINA (USA).

  • Premium

    Solutions for dust control in tool hire

    In the hire business, dust control is well understood, at least for clients. However, protection of employees against dust from returned tools is another matter. A huge number of hire businesses receive tools back from clients and then use an airline to blow them clean – without knowing or identifying the dust contained within the unit. Often the process takes place outside, to avoid dust contaminating the workshop. This is all bad practice – in particular, for cases when the tool may be contaminated ...

    By AirBench Ltd. based in Colchester, UNITED KINGDOM.

  • Premium

    Application package FLUXANA Slag

    This application package is a 'ready to go' calibration kit for xrf instruments. The analysis of slags in the metal industry delivers important information about the production process. FLUXANA has developed a fusion slag method which allows the direct analysis of most common slags. Elements of interest and calibrated concentration ranges can be selected individually by the customer. The same application program can also be easily adapted to the analysis of different filter dusts (see ...

    By Fluxana GmbH Co. KG based in Bedburg-Hau, GERMANY.

  • Premium

    Air pollution, emission and process monitoring systems for food & pharma

    High accuracy measurement and reliability in monitoring instrumentation is called for by Food and Pharmaceutical Processes. ENVEA’s unique capabilities allow the observation and control of many of the manufacturing functions found in these industries. From the measurement and control of emitted dust from dryer filter plant to the non-intrusive, solid state measurement of powder mass flow and the monitoring of process gas quality, ENVEA instrumentation provides Plant Operators with the opportunity to fine ...

    By ENVEA based in Poissy, FRANCE.

  • Premium

    Engineered clean air solutions for lean manufacturing applications

    Whether you call it lean manufacturing or Just-in-Time (JIT) manufacturing, eliminating waste isn’t a new concept for bottom-line minded manufacturers. But, it isn’t easy to reduce operating costs while creating more value for your customers. This is especially the case for welding, sanding, painting, or other processes that produce harmful air contaminants and create production bottlenecks for larger construction projects. What if you had a portable, clean air solution to protect your employees from ...

    By Duroair Technologies Inc. based in Niagara Falls, ONTARIO (CANADA).

  • Premium

    Engineered clean air solutions for stone cutting applications

    Stone cutting is one of the messiest operations in manufacturing – and the most hazardous. When it comes to producing dust, stone cutting generates clouds of dust that is far from harmless. Most concrete, masonry, and stone contain sand that is made of quartz and creates crystalline silica when cut. The inhalation of silica particles can scar the lungs or even lead to silicosis. Of course, you don’t need OSHA and NIOSH to tell you that silica dust is dangerous. What if you had a portable clean air ...

    By Duroair Technologies Inc. based in Niagara Falls, ONTARIO (CANADA).

  • Premium

    Application package FLUXANA Iron Ore

    This application package is a 'ready to go' calibration kit for xrf instruments. The analysis of iron ore industry delivers important information about the production process. FLUXANA has developed a fusion slag + filter dusts method which allows the direct analysis of most common slags and filter dusts. Elements of interest and calibrated concentration ranges can be selected individually by the ...

    By Fluxana GmbH Co. KG based in Bedburg-Hau, GERMANY.

  • Premium

    Special plants for recycling of toners

    Printer consumables and empty toner cartridges cannot be grouped with municipal solid waste but require special treatment for recycling. FORREC has designed an exclusive plant that provides specific processing for this type of waste. The system developed and produced by Forrec consists in a treatment with a four-shaft shredder that provides a reduction to less than 40mm allowing the subsequent separation of iron, plastic and non-ferrous materials. A dust suction system is combined with a shredding ...

    By Forrec srl based in Santa Giustina in Colle, ITALY.

  • Premium

    Industrial screening solutions for chemical industry

    Looking to get ahead in a competitive industry in tough economic times can be challenging, this is sometimes the case in the chemical industry. Therefore, we at VibraScreener™ understand that a clean, free from contamination and correct size product can be the difference to set you apart from your competitors, and is for this reason that we design and manufacture vibratory sieves and industrial sieving machines dedicated to helping you with this important ...

    By VibraScreener Inc. based in Charlotte, NORTH CAROLINA (USA).

  • Premium

    Industrial screening solutions for ceramics industry

    Because the ceramic industry plays an important role in our everyday life, this is an exciting industry to us and we are glad to be part of it. As ceramic products are all around us, from basic construction materials and household products to very sophisticated products such as refractory and dental implants, we understand the importance of the quality of their materials and how defining this can be to ceramic products competitiveness and bottom line profitability. Because of these facts we have introduced ...

    By VibraScreener Inc. based in Charlotte, NORTH CAROLINA (USA).

  • Premium

    Industrial screening solutions for minerals industry

    In a commodity business, one complaint can ruin your reputation to one of your customers and many of their friends. This is the case in companies dealing with minerals, although they are considered commodities avoiding complaints about product contamination or bad sizes can mean the return of your customers. At VibraScreener™ our mission is to help you stay complaints free and ensure your company sustainability by designing and manufacturing high-quality vibratory screeners and industrial separators to ...

    By VibraScreener Inc. based in Charlotte, NORTH CAROLINA (USA).

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you